Hitachi Projector CP-WU9100 User Manual

71
ItemDescription
LAMP & FILTER
Selecting this item displays the LAMP & FILTER menu.Select an item using the ▲/▼ buttons, and press the ► button or the ENTER 
button on the remote control to execute the item.
ECO MODE
Using the ▲/▼ buttons turns off/on the Eco mode.
NORMAL  ECO
•  When the ECO is selected, acoustic noise and screen brightness are reduced.
LAMP MODE
Using the ▲/▼ cursor buttons changes the Lamp Mode.
DUAL : Use both lamp at the same time.ALTERNATE :   Use the lamps alternately according...

72
ItemDescription
LAMP & FILTER(continued)
CYCLE TIME
Using the ▲/▼ cursor buttons changes the CYCLE TIME.
          6h  12h  18h  24h  1 week
           
Lamp switches according to the setting here.
•  
This function is only available if CYCLE TIME is selected at ALTERNATE 
of LAMP MODE.
LAMP-1 TIME 
The lamp time is the usage time of the lamp-1, counted after the last resetting. It is shown in the LAMP & FILTER menu.Pressing the RESET button on the remote control or the ► button of the projector...

73
ItemDescription
LAMP & FILTER(continued)
FILTER TIME 
Displays the usage time of the air filter, counted after the last resetting. It is shown in the LAMP & FILTER menu.Pressing the RESET button on the remote control or the ► button of the projector displays a dialog. To reset the filter time, select the OK using the ► button.
CANCEL  OK
• Reset the filter time only when you have cleaned or replaced the air filter, for a suitable indication about the air filter.• For the air filter cleaning, see the...

74
ItemDescription
INSTALLATION
Pressing the ►button displays the dialog for changing the 
INSTALLATION setting.
 FRONT / DESKTOP
   
 REAR / DESKTOP
   
 REAR / CEILING
  
 FRONT / CEILING
Use the ▲/▼ buttons to select the required setting on the INSTALLATION dialog, and press the ENTER button of the remote control or the INPUT button of the projector to execute.
STANDBY MODE
Using ▲/▼ buttons switches the standby mode setting between NORMAL and SAVING. 
NORMAL  SAVING
• When SAVING is selected, the...

75
ItemDescription
OSD MESSAGE
SETUP menu
Using the ▲/▼ buttons turns on/off the message function.
NORMAL  SILENT INHIBIT 
   
■SILENT : The following message functions do not work.
“AUTO IN PROGRESS” while automatically adjusting“NO INPUT IS DETECTED”“SYNC IS OUT OF RANGE”“INVALID SCAN FREQ.”“NOT AVAILABLE”“Searching….” while searching for the input“Detecting….” while an input signal is detectedThe indication of the ZOOM displayed by changing      *While operating from the remote control only.The...

76
SCREEN menu
ItemDescription
LANGUAGE
Using the ▲/▼/◄/► buttons switches the OSD (On Screen Display) language.
ENGLISH  FRANÇAIS  DEUTSCH   ESPAÑOL         (shown in the LANGUAGE dialog)  
Press the ENTER or INPUT button to save the language setting.
MENU POSITIONUsing the ▲/▼/◄/► buttons adjusts the menu position.To quit the operation, press the MENU button on the remote control or do not perform any operation for about 10 seconds.
BLANK
Using the ▲/▼ buttons switches the mode for the blank...

77
SCREEN menu
ItemDescription
AUTO BLANK
Using the ▲/▼ buttons switches the mode for the AUTO BLANK screen.
BLUE  WHITE  BLACK       
• To avoid remaining as an afterimage, displayed image will changeto the designated blank color screen by AUTO BLANK after severalminutes at the following conditions.- When MyScreen or ORIGINAL is displayed as BLANK screen.- When start-up screen is displayed.
START UP
Using the ▲/▼ buttons switches the mode for the start-up screen.The start-up screen is a screen...

78
SCREEN menu
ItemDescription
MyScreen
You can capture an image for use as a MyScreen image which can be used as the BLANK screen and START UP screen. Display the image you want to capture before executing the following procedure.
(1)  Selecting this item displays a dialog titled “MyScreen”. It will ask you if you start capturing an image from the current screen.Wait for the target image to be displayed, and press the ENTER or INPUT button when the image is displayed. The image will freeze and the frame...

79
SCREEN menu
ItemDescription
MyScreen Lock
Using the ▲/▼ buttons turns on/off the MyScreen lock function.
ON  OFF
When the ON is selected, the item MyScreen is locked. Use this function for protecting the current MyScreen.
• This function cannot be selected when the ON is selected to the 
MyScreen PASSWORD item in SECURITY menu (97).
SOURCE NAME
Each input port for this projector can have a name applied to it.
(1)  Use the ▲/▼ buttons on the SCREEN menu to select SOURCE NAME and press the ► or ENTER...

80
SCREEN menu
ItemDescription
SOURCE NAME
(continued)
(6)  
The current name will be displayed on 
the first line. Use the ▲/▼/◄/► buttons and the ENTER or INPUT button to select and enter characters. To erase one character at a time, press the RESET button or press the ◄ and INPUT button simultaneously. Also if you move the cursor to DELETE or CLEAR ALL on screen and press the ENTER or INPUT button, one or all characters will be erased. The name can be a maximum of 16 characters.
(7)  
To change an...