Hitachi Projector CP-WU9100 User Manual

11
Setting up
Connecting with your devices
Before connecting the projector to a device, consult the manual of the device to 
confirm that the device is suitable for connecting with this projector and prepare 
the required accessories, such as a cable in accord with the signal of the device. 
Consult your dealer when the required accessory did not come with the product or 
the accessory is damaged.
After making sure that the projector and the devices are turned off, perform 
the connection, according to...

12
Setting up
Computer
DVIHDBaseTTM
• Before connecting the projector to a computer, consult the computer’s 
manual and check the compatibility of the signal level, the synchronization 
methods and the display resolution output to the projector. 
-  Some signal may need an adapter to input this projector.
-  Some computers have multiple screen display modes that may include some 
signals which are not supported by this projector.
-  
Although the projector can display signals with a resolution up to UXGA...

13
External deviceComputer
Setting up
Access 
point
USB wireless adapter 
(optional)
     WARNING►Heat may build up in the USB wireless adapter, to avoid 
possible burns disconnect the projector power cord for 10 minutes before 
touching the adapter.   
                                                                                                    ► Before connecting the projector to a network system be 
sure to obtain the consent of the administrator of the network.
►Do not connect the LAN port to...

14
Setting up
VCR/DVD/Blu-ray DiscTM player
VIDEO OUTHDBaseTTM
• HDBaseT is a technology to transmit image, sound, ethernet or serial control 
signal using a LAN cable.
• Go to the following URL regarding the device of other company that supports 
HDBaseT and has been confirmed compatible with this projector.
http://www.hitachi.co.jp/proj/
LAN or HDBaseT input port can be selected as ethernet signal input by 
switching in the menu.
• Use LAN cables of up to 100m long. Exceeding this length, the image...

15
Setting up
• The HDMI ports of this model are compatible with HDCP (High-band-
width Digital Content Protection) and therefore capable of displaying video 
signals from HDCP compatible DVD players or the like.
-  
The HDMI ports support the following signals:
Video signal :   480i@60, 480p@60, 576i@50, 576p@50, 720p@50/60, 
1080i@50/60, 1080p@50/60
PC signals : See User’s Manual (detailed) Technical
-  
This projector can be connected with another equipment that has HDMI  
connector, but with some...

16
Monitor
Setting up
(Wired) Remote control
Another projector
• To use a wired remote control, connect a wired remote control to the 
REMOTE CONTROL IN port. You can also connect another projector to the 
REMOTE CONTROL OUT port to control it from the wired remote control. You 
can use this projector as a remote control-relay with the REMOTE CONTROL 
IN and OUT ports. To connect the wired remote control or another projector 
to the REMOTE CONTROL IN or OUT ports, use audio cables with 3.5 mm 
diameter...

17
SDI OUT
Setting up
• The SDI port of this model supports the following SDI signals:
SD-SDI signal: conforming to SMPTE ST 259-C standard
YCBCR 4:2:2 10-bit
480i, 576i
Single link HD-SDI signal: conforming to SMPTE ST 292 standard
YPBPR 4:2:2 10-bit
720p@50/60, 1080i@50/60, 1080Psf@25/30
3G-SDI Level-A signal: conforming to SMPTE ST 424 standard
YPBPR 4:2:2 10-bit
1080p@50/60
-  
This projector can be connected with other equipment that has SDI connector , 
but with some equipment the projector may not...

18
►Use only a plastic tie to get together or fasten the cables. A 
metallic tie may cause damage to the cables and tie holder.
►Do not bind the cables too tightly. The cables or the hole might be damaged.
CAUTION
Fastening the cables
Use the supplied cable tie 
to fasten the cables.
Cable tie
Holes for Cable tie
Holes for Cable tie
Setting up 

19
1. Loosen the screw  on the bottom left of the WIRELESS port.
Ta b
2. Insert the tab of the cover into the hole at the upper right of the WIRELESS 
port in the direction of the arrow.
3. Align the screw holes on the projector and the cover. Then insert the screw 
removed from the projector into the hole and tighten the screw.
Fastening the adapter cover
►Keep small parts away from children and pets. Take care not 
to put in the mouth. 
►Heat may build up in the USB wireless adapter, to avoid possible...

20
Using the security bar and slot
A commercially available anti-theft chain or 
wire can be attached to the security bar on 
the projector. Refer to the figure to choose 
an anti-theft chain or wire.
Also this product has the security slot for 
the Kensington lock. 
For details, see the manual of the security 
tool.
►Do not use the security bars and slot to prevent the projector 
from falling down, as it is not designed for it.
►Do not place anti-theft chain or wire near the exhaust vents.  
It may...