Hitachi Projector CP-D27WN User Manual

							81
SECURITY menu
ItemDescription
PIN LOCK
PIN LOCK is a function which prevents the projector from being used unless 
a registered Code is input.
1 Turning on the PIN LOCK1-1   Use the ▲/▼ buttons on the SECURITY menu to 
select PIN LOCK and press the ► button or the 
ENTER button to display the PIN LOCK on/off 
menu.
1-2   Use the ▲/▼ buttons on the PIN LOCK on/
off menu to select ON and the Enter PIN 
Code box will be displayed. 
1-3   Input a 4 part PIN code using the ▲/▼/◄/►, 
COMPUTER or INPUT button. 
The PIN Code again box will appear. Reenter 
the same PIN code. This will complete the PIN 
code registration.
• If there is no key input for about 55 seconds   
while the Enter PIN Code box or the PIN Code again box is displayed, 
the menu will close. If necessary, repeat the process from 1-1.
Afterwards, anytime the projector is restarted after AC power is turned off 
the Enter PIN Code box will be displayed. Enter the registered PIN code.
The projector can be used after entering the registered PIN code. If an 
incorrect PIN code is input, the Enter PIN code box will be displayed again.
If an incorrect PIN code is input 3 times, the projector will turn of f. Afterwards 
the projector will turn off every time an incorrect PIN code is input. The 
projector will also turn off if there is no key input for about 5 minutes while 
the Enter PIN code box is displayed.
This function will activate only when the projector is started after  AC power 
is turned off.
• Please do not forget your PIN code.
2 Turning off the PIN LOCK2-1   Follow the procedure in 1-1 to display the PIN LOCK on/off menu. 
2-2   Use the ▲/▼ buttons to select OFF and the Enter PIN Code box will be 
displayed.  
Enter the registered PIN code to turn the PIN LOCK function off.
If an incorrect PIN code is input 3 times, the projector will turn of f.
3 If you have forgotten your PIN code3-1  While the Enter PIN code box is displayed, press and hold the  RESET 
button for 3 seconds or press and hold the  INPUT button for 3 seconds 
while pressing the ► button on the projector. 
The 10 digit Inquiring Code will be displayed.
• If there is no key input for about 5 minutes 
while the Inquiring Code is displayed, the 
projector will turn off.
3-2   Contact your dealer with the 10 digit Inquiring Code. Your PIN code will 
be sent after your user registration information is confirmed.
(continued on next page) 
						

							82
SECURITY menu
ItemDescription
TRANSITION  DETECTOR
If this function is set to ON and the vertical angle of
the projector or the INSTALLATION setting is different
from the previous recorded setting, the TRANSITION
DETECTOR ON alarm will be displayed and the input
signal will not be displayed.
• To display the signal again, set this function OFF.
• After about 5 minutes of displaying the TRANSITION DETECTOR ON 
alarm, the lamp will turn off.
• Keystone adjustment feature has been prohibited as long as the 
TRANSITION DETECTOR function is on.
1 Turning on the TRANSITION DETECTOR1-1   Use the ▲/▼ buttons on the SECURITY menu 
to select TRANSITION DETECTOR and press 
the ► or the  ENTER button to display the 
TRANSITION DETECTOR on/off menu.
1-2  
Use the ▲/▼ buttons on the TRANSITION 
DETECTOR on/off menu to select ON. 
Selecting ON will save the setting of the 
current angle and the INSTALLATION setting. 
The ENTER NEW PASSWORD box (small) 
will be displayed.
1-3  Use the ▲/▼/◄/► buttons to enter a 
password. Move the cursor to the right side 
of the ENTER NEW PASSWORD box (small) 
and press the ► button to display the NEW 
PASSWORD AGAIN box, enter the same 
password again.
1-4   Move the cursor to the right side of the  
NEW PASSWORD AGAIN box and press the ► button to display the 
NOTE NEW PASSWORD box for about 30 seconds, please make note 
of the password during this time.
Pressing the ENTER button on the remote control or the ► button on the 
projector will return to the TRANSITION DETECTOR on/off menu.
• Please do not forget your TRANSITION DETECTOR password.
• This function will activate only when the projector is started after turning off 
the AC power.
• This feature may not function properly if the projector is not in a stable 
position when ON is selected.
2 Turning off the TRANSITION DETECTOR2-1  Follow the procedure in 1-1 to display the TRANSITION DETECTOR on/off menu.2-2  Select OFF to display the ENTER 
PASSWORD box (large). Enter the registered 
password and the screen will return to the 
TRANSITION DETECTOR on/off menu.
If an incorrect password is input, the menu will 
close. If necessary, repeat the process from 2-1.
3 If you have forgotten your password3-1  Follow the procedure in 1-1 to display the TRANSITION DETECTOR on/off menu.3-2   Select OFF to display the ENTER PASSWORD box (large). The 10 digit 
Inquiring Code will be displayed inside the box.
3-3   Contact your dealer with the 10 digit Inquiring Code. Your password will 
be sent after your user registration information is confirmed.
(continued on next page)
ENTER NEW PASSWORD 
box (small)
ENTER PASSWORD box  (large) 
						

							83
SECURITY menu
ItemDescription
MY TEXT 
PASSWORD
The MY TEXT PASSWORD function can prevent the MY TEXT from being 
overwritten. When the password is set for the MY TEXT;
• The MY TEXT DISPLAY menu will be unavailable, which can prohibit 
changing the DISPLAY setting.
• The MY TEXT WRITING menu will be unavailable, which can prevent the 
MY TEXT from being overwritten.
1 Turning on the MY TEXT PASSWORD1-1   Use the ▲/▼ buttons on the SECURITY menu to 
select the MY TEXT PASSWORD and press the 
► button to display the MY TEXT PASSWORD 
on/off menu.
1-2   Use the ▲/▼ buttons on the MY TEXT 
PASSWORD on/off menu to select ON. The 
ENTER NEW PASSWORD box (small) will 
be displayed.
1-3   Use the ▲/▼/◄/► buttons to enter the 
password. Move the cursor to the right side 
of the ENTER NEW PASSWORD box (small) 
and press the ► button to display the NEW 
PASSWORD AGAIN box, and then enter the 
same password again.
1-4   Move the cursor to the right side of the 
NEW PASSWORD AGAIN box and press 
► button to display the NOTE NEW 
PASSWORD box for about 30 seconds, then 
please make note of the password during 
this time.
Pressing the ENTER button on the remote control or ► button on the 
projector will return to the MY TEXT PASSWORD on/off menu. 
2 Turning off the MY TEXT PASSWORD2-1   Follow the procedure in 1-1 to display the MY TEXT PASSWORD on/off 
menu.
2-2   Select OFF to display the ENTER 
PASSWORD box (large). Enter the 
registered password and the screen will 
return to the MY TEXT PASSWORD on/off 
menu. 
If an incorrect password is input, the menu will close. 
If necessary, repeat the process from 2-1
3 If you have forgotten your password3-1   Follow the procedure in 1-1 to display the MY TEXT PASSWORD on/off 
menu.
3-2   Select OFF to display the ENTER PASSWORD box (large). The 10 digit 
inquiring code will be displayed inside the box. 
3-3   Contact your dealer with the 10 digit inquiring code. Your password will 
be sent after your user registration information is confirmed.
ENTER NEW PASSWORD  
box (small)
ENTER PASSWORD box  (large)
(continued on next page) 
						

							84
SECURITY menu
ItemDescription
MY TEXT  DISPLAY
(1)   Use the ▲/▼ buttons on the SECURITY menu to 
select the MY TEXT DISPLAY and press the ► or 
ENTER button to display the MY TEXT DISPLAY 
on/off menu.
(2)   Use the ▲/▼ buttons on the MY TEXT DISPLAY on/off menu to select 
on or off.
ON  ó OFF
When it is set ON, the MY TEXT will be displayed 
on the START UP screen and the INPUT_
INFORMATION when the INFORMATION on the 
SERVICE menu is chosen.
• This function is available only when the MY TEXT 
PASSWORD function is set to the OFF.
MY TEXT 
WRITING
(1)   Use the ▲/▼ buttons on the 
SECURITY menu to select the MY 
TEXT WRITING and press the ► 
button. The MY TEXT WRITING dialog 
will be displayed.
(2)    The current MY TEXT will be displayed 
on the first 3 lines. If not yet written, the 
lines will be blank.   
Use the ▲/▼/◄/► buttons and the 
ENTER or INPUT button to select and 
enter characters. To erase 1 character, 
press the RESET button or press the 
◄ and INPUT button at the same time. 
Also if you move the cursor to DELETE 
or ALL CLEAR on screen and press the 
ENTER or INPUT button, 1 character 
or all characters will be erased. The MY 
TEXT can be input up to 24 characters 
on each line.
(3)    To change an already inserted 
character, press the ▲/▼ button to 
move the cursor to one of the first 3 
lines, and use the ◄/► buttons to 
move the cursor on the character to be 
changed.
After pressing the ENTER or INPUT button, the character is selected. 
Then, follow the same procedure as described at the item (2) above.
(4)    To finish entering text, move the cursor to the OK on screen and press 
the ►,  ENTER or INPUT button. To revert to the previous MY TEXT 
without saving changes, move the cursor to the CANCEL on screen and 
press the ◄,  ENTER or INPUT button.
• The MY TEXT WRITING function is available only when the MY TEXT 
PASSWORD function is set to OFF.
CLONING LOCKThe CLONING operation under OPTION_SERVICE menu is not available if
ON is selected. 
						

							85
Presentation toolsPresentation tools
Presentation tools
The PC-LESS Presentation reads image and audio data from the storage media 
inserted into the USB TYPE A port and displays the image in the following modes.
The PC-LESS Presentation can be started by selecting the USB TYPE A port as 
the input source.
This feature allows you to make your presentations without using your computer .
PC-LESS Presentation
- Thumbnail mode (86)
- Full Screen mode (
90)
- Slideshow mode (
92)
[Supported storage media] • USB memory (USB memory type, USB hard disk and USB card reader type)
• USB readers (adapters) that have more than one USB slot may not 
work (if the adapter is acknowledged as multiple devices connected).
• USB devices with security software may not work.
• Be careful when inserting or removing a USB device. (
14, 88)
NOTE
• NTFS is not supported.
NOTE
[Supported format]
• FAT12, FAT16 and FAT32
The projector has the following convenient tools that enable on-screen presentations 
easily and quickly:
- PC-LESS Presentation (below)
-   Drawing function   
Drawing function enables you to draw on the projector’s screen with USB 
mouse or tablets connected to the USB TYPE A ports. 
For details, refer to the manual for peripheral equipment.
- USB Display (
95, 99) 
						

							86
Presentation toolsPresentation tools
• Files with a resolution larger than the following are not supported. 
CP-D27WN, 
CP-D32WN: 1024 x 768 (Still)，  768 x 576 (Movie)
CP-DW25WN: 1280 x 800 (Still)，  768 x 576 (Movie)
(* Some computers may not support 1280 x 800.)
• Files with a resolution smaller than 36 x 36 are not supported.
• Files with a resolution smaller than 100 x 100 may not be displayed.
• Movie images with a frame rate higher than 15 fps cannot be displayed.
• Movie images with a bit rate higher than 20 Mbps cannot be displayed.
• Some supported files may not be displayed.
• Only a frame appears when the content of image data cannot be displayed in 
the Thumbnail mode.
• Even with the file format and audio format combinations described above, 
playback of some files may fail. NOTE
[Supported file format and its extension]
• JPEG (.jpeg, .jpg)  * Progressive is not supported.
• Bitmap (.bmp)  *  16bit mode and compressed bitmap is not supported.
• PNG (.png)  * Interlace PNG is not supported.
• GIF (.gif) 
• Movie (.avi, .mov)  *  
Supported video format: Motion-JPEG 
Supported audio format:  
WAV (Linear PCM, Stereo 
16bit), 
IMA-ADPCM
Thumbnail mode
PC-LESS Presentation (continued)
The Thumbnail mode displays the images stored in a USB storage device on the 
Thumbnail screen. Maximum 20 images are displayed in a screen.
If you wish, you can jump into the Full Screen mode or Slideshow mode, after you 
select some images in the Thumbnail mode.
The Thumbnail mode will be started as the primary function of the PC-LESS 
Presentation after selecting the  USB TYPE A port as the input source.
Thumbnail menu
Selected image
Thumbnail images 
						

							87
Presentation toolsPresentation tools
PC-LESS Presentation (continued)
The SETUP menu for the selected image
ItemFunctions
SETUP Use the ◄/► cursor buttons to switch each setting or use the ► cursor 
button to execute the functions as follows.
RETURN Press the ► cursor button or ENTER to return to the Thumbnail screen.
START Switch to ON to set the selected image as the first image in the 
Slideshow. This setting information will be saved in the 
“playlist.txt” file 
(
94).
STOP Switch to ON to set the selected image as the last image in the 
Slideshow. 
This setting information will be saved in the  “playlist.txt” file 
(
94).
SKIP Switch to ON to skip the selected image in the Slideshow. This setting 
information will be saved in the 
“playlist.txt” file (
94).
ROTATE Press the ► cursor or ENTER button to rotate the selected still image 
90 degrees clockwise. 
This setting information will be saved in the 
“playlist.txt” file (
94).
You can control the images on the Thumbnail screen with the remote control, 
control panel or Web Remote Control. The following functions can be supported 
while the Thumbnail is displayed. Operating by buttons or keys
Button operation
Functions
The remote 
control Control panel
Web Remote 
Control
▲/▼/◄/► ▲/▼/◄/►[▲]/[▼]/[◄]/[►] Move cursor
PAGE UP
PAGE DOWN -[PAGE UP]
[PAGE DOWN] Switches pages
ENTER INPUT[ENTER] • Displays the selected image 
on the Full Screen mode when a 
cursor is on a thumbnail image. 
• Displays the SETUP menu 
(
below) for the selected image 
when a cursor is on a thumbnail 
image number. 
						

							88
Presentation tools
You can also control the images by using the menu on the Thumbnail screen. PC-LESS Presentation (continued)
Operating by the menu on the Thumbnail screen
ItemFunctions
Moves to an upper folder.
SORT Allows you to sort files and folders as following.
RETURN Press the ► cursor button or ENTER to return to the Thumbnail 
screen.
NAME UP Sorts in ascending order by file name.
NAME DOWN Sorts in descending order by file name.
DATE UP Sorts in ascending order by file date.
DATE DOWN Sorts in descending order.by file date.
▲/▼ Go to previous / next page.
SLIDESHOW Configures and starts the Slideshow  (
92).
RETURN Press the ► cursor button or ENTER to return to the Thumbnail 
screen.
PLAY Press the ► cursor button or ENTER to start the Slideshow.
START Sets the beginning number of the Slideshow.
STOP Sets the end number of the Slideshow.
INTERVAL Sets the interval time for displaying still images during the 
Slideshow.
PLAY MODE Selects the Slideshow mode.
INPUT Switches the input port.
MENU  Displays the menu.
REMOVE USB Be sure to use this function before removing USB storage device 
from the projector. After that, the projector will not recognize a 
USB storage device until you insert it again into the 
USB TYPE A 
input port. 
 / Turns the sound on/off for files that contain audio data. 
						

							89
Presentation tools
PC-LESS Presentation (continued)
• These operations are not accessible while the projector OSD is displayed.
• The Thumbnail mode is able to display up to 20 files in one page.
• It is not possible to change the input port by using the INPUT button when the 
Thumbnail screen, Slideshow, or Full Screen is displayed.
• The image quality may deteriorate when playing back audio data included in 
a movie. If you want to give priority to the image quality, turn off the sound by 
setting ♪ to off.
• If one of the  AUDIO IN ports is selected or 
 is selected for USB TYPE A in 
AUDIO SOURCE of the AUDIO menu (
48), ♪ cannot be operated.
• Some error icons will be displayed in the Thumbnail. NOTE
This file seems to be broken or not supported format.A file that cannot be displayed on the 
thumbnail screen is indicated by a file 
format icon. 
						

							90
Presentation tools
PC-LESS Presentation (continued)
The Full Screen mode shows a full display image. To display in Full Screen mode, 
select an image in the Thumbnail screen. Then press the ENTER button on the 
remote control, the INPUT button on the control panel or click [ENTER] on the 
Web Remote Control.
Full Screen Mode
Button operation
Functions
The remote 
control Control panel
Web Remote 
Control
▼  
► 
or
PAGE DOWN ▼ 
or  
► [▼] 
 
[►]
or
[PAGE DOWN]
Shows the next file.
▲ 
◄
or  
PAGE UP ▲ 
or  
◄[▲] 
[◄]
or  
[PAGE UP]
Shows the previous file.
ENTER
INPUT[ENTER] Displays Thumbnail.
The following operations are enabled in the Full Screen mode while a still image 
is displayed.
Full screen display
Operations for still images