Hitachi Projector CP-D27WN User Manual

							21
VIDEODOC.CAMERA
KEYSTONE
ASPECTSEARCHBLANK
MUTE
MY BUTTON
POSITION ESC MENU
RESET
COMPUTER MY SOURCE/
AUTOMAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
ー
＋VOLUME
1 2
ENTER
Operating
Operating
1.
Adjusting the volume
Use the VOLUME +/VOLUME - buttons to adjust the volume.
A dialog will appear on the screen to aid you in adjusting the 
volume. If you do not do anything, the dialog will automatically 
disappear after about ten seconds.
●  When 
 is selected for current picture input port, the volume adjustment is 
disabled. Please see AUDIO SOURCE item of AUDIO menu (48).
●   Even if the projector is in the standby mode, the volume is adjustable in the 
following conditions:
-  An option other than 
 is selected for STANDBY in the AUDIO SOURCE 
item of the AUDIO menu (48).
- NORMAL is selected in the STANDBY MODE item of the SETUP menu ( 46).
●   In the standby mode, the volume of the microphone is adjustable with the 
VOLUME +/- buttons on the remote control, in synchronization with the volume 
of the projector (
 13) .
1.Press MUTE button on the remote control. 
A dialog will appear on the screen indicating that you have muted 
the sound. 
To restore the sound, press the  MUTE, VOLUME + or 
VOLUME - button. Even if you do not do anything, the dialog 
will automatically disappear after about ten seconds.
Temporarily muting the sound
●  When  is selected for current picture input port, the sound is always muted. 
Please see AUDIO SOURCE item of AUDIO menu (
48).
●  C.C. (Closed Caption) is automatically activated when sound is muted and an  input signal containing C.C. is received. This function is available only when 
the signal is NTSC for VIDEO or S-VIDEO, or 480i@60 for COMPUTER IN1 
or COMPUTER IN2, and when AUTO is selected for DISPLAY in the C.C. 
menu under the SCREEN menu (
55).
1.Press INPUT button on the projector. 
Each time you press the button, the projector 
switches its input port from the current port as below.
Selecting an input signal
(continued on next page)
●  While ON is selected for AUTO SEARCH item in OPTION menu ( 56), the projector 
will keep checking the ports in above order repeatedly till an input signal is detected.
● It may take several seconds to project the images from the USB TYPE B port.
VIDEODOC.CAMERA
KEYSTONE
ASPECT SEARCHBLANK
MUTE
MY BUTTON
POSITION ESC MENU
RESET
COMPUTER MY SOURCE/
AUTOMAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
ー
＋VOLUME
1 2
ENTER
VOLUME +/- button
MUTE button
                COMPUTER IN1  COMPUTER IN2  
    VIDEO                                                             LAN
    S-VIDEO                                           USB TYPE A
                
    HDMI      
 USB TYPE B
INPUT button 
						

							22
VIDEODOC.CAMERA
KEYSTONE
ASPECTSEARCHBLANK
MUTE
MY BUTTON
POSITION ESC MENU
RESET
COMPUTER MY SOURCE/
AUTOMAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
ー
＋VOLUME
1 2
ENTER
Operating
1.Press VIDEO button on the remote control. 
Each time you press the button, the projector switches its 
input port from the current port as below.
Selecting an input signal (continued)
●  While ON is selected for AUTO SEARCH item in OPTION 
menu, the projector will keep checking every port sequentially 
till an input signal is detected (
56). If 
VIDEO button is 
pressed when  COMPUTER IN1, COMPUTER IN2, LAN, USB 
TYPE A or USB TYPE B port is selected, the projector will 
check HDMI port fi rst. 
1.Press COMPUTER button on the remote control. 
Each time you press the button, the projector switches its 
input port from the current port as below.
●  While ON is selected for AUTO SEARCH item in OPTION  menu, the projector will keep checking every port sequentially 
till an input signal is detected (
56). If  COMPUTER button is 
pressed when  VIDEO, S-VIDEO or HDMI port is selected, the 
projector will check  COMPUTER IN1 port fi rst.
●     It may take several seconds to project the images from the 
USB TYPE B port.
1.Press the MY SOURCE / DOC. CAMERA button on 
the remote control. The input signal will be changed 
into the signal you set as MY SOURCE (
60).
●  This function also can use for document camera. Select the  input port that connected the document camera.
         COMPUTER IN1  COMPUTER IN2  LAN
               USB TYPE B        USB TYPE A
        HDMI    S-VIDEO  
                 VIDEO 
VIDEO button
VIDEODOC.CAMERA
KEYSTONE
ASPECT
SEARCHBLANK
MUTE
MY BUTTON
POSITION ESC MENU
RESET
COMPUTER MY SOURCE/
AUTOMAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
ー
＋VOLUME
1 2
ENTER
VIDEODOC.CAMERA
KEYSTONE
ASPECT
SEARCHBLANK
MUTE
MY BUTTON
POSITION ESC MENU
RESET
COMPUTER MY SOURCE/
AUTOMAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
ー
＋VOLUME
1 2
ENTER
MY SOURCE / 
DOC. CAMERA button
COMPUTER button 
						

							23
1.Press ASPECT button on the remote control.  
Each time you press the button, the projector switches the 
mode for aspect ratio in turn. 
Selecting an aspect ratio
● ASPECT button does not work when no proper signal is inputted.
● NORMAL mode keeps the original aspect ratio setting.
●  The on-screen menu might be displayed outside of the image display area 
depending on the adjustment value of the ASPECT, D-ZOOM and 
 KEYSTONE. Changing the values of ASPECT, D-ZOOM and   
 KEYSTONE may fi x the symptom.
1.Press SEARCH button on the remote control.
The projector will start to check its input ports as below in 
order to fi nd any input signals.
When an input is detected, the projector will stop searching 
and display the image. If no signal is found, the projector will 
return to the state selected before the operation.
Searching an input signal
●  While ON is selected for AUTO SEARCH item in OPTION menu (56), the 
projector will keep checking the ports in the above order repeatedly till an 
input signal is detected.
●  
It may take several seconds to project the images from the USB TYPE B port.
  For a computer signal
NORMAL  4:3  16:9  16:10  NATIVE
     
  For a video signal, s-video signal or component video  signal
4:3  16:9  16:10  14:9  NATIVE
 
  For an input signal from the LAN, USB TYPE A or USB TYPE B port, or  if there is no signal 
CP-D27WN/CP-D32WN: 4:3 (fi xed) 
CP-DW25WN: 16:10 (fi xed)
Operating
  For an HDMITM signal
NORMAL  4:3  16:9  16:10  14:9  NATIVE
     
ASPECT button
VIDEODOC.CAMERA
KEYSTONE
ASPECT SEARCHBLANK
MUTE
MY BUTTON
POSITION ESC MENU
RESET
COMPUTER MY SOURCE/
AUTOMAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
ー
＋VOLUME
1 2
ENTER
                COMPUTER IN1  COMPUTER IN2  
    VIDEO                                                             LAN
    S-VIDEO                                           USB TYPE A
                
    HDMI      
 USB TYPE B
SEARCH  button
VIDEODOC.CAMERA
KEYSTONE
ASPECT
SEARCHBLANK
MUTE
MY BUTTON
POSITION ESC MENU
RESET
COMPUTER MY SOURCE/
AUTOMAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
ー
＋VOLUME
1 2
ENTER 
						

							24
Operating
Adjusting the focus
Adjusting the projector's elevator
The  projector  has  Front  foot  for  inclinations  and  Rear  foot  for  horizontals. A  spacer 
is  installed  on  the  Rear  elevator  foot  at  the  time  of  shipment,  and  the  projector 
is  ready  for  use.  If  necessary,  detach  the  spacer,  and  the  elevator  feet  can  be 
manually twisted to make more precise adjustments.
Front footRear foot
0~2°
-1~1°
Front foot
Rear footSpacer    Spacer
Use the focus ring to focus the picture.
►Keep the spacer away from children and pets. Be careful not 
to let them swallow the spacer. If swallowed consult a physician immediately for 
emergency treatment. WARNING
• The Front foot can be adjusted within 0~2°, while the Rear foot can 
be adjusted within -1~1°.
• 
After the foot is adjusted, it is possible to return it to the state of the shipment with a spacer.  
It is recommended to keep the spacer and reuse it when relocating the projector.
NOTE
FOCUS ring 
						

							25
Operating
1.Press AUTO button on the remote control. 
Pressing this button performs the following.
Using the automatic adjustment feature
  For a computer signal
The vertical position, the horizontal position and the horizontal 
phase will be automatically adjusted. 
Make sure that the application window is set to its maximum size 
prior to attempting to use this feature. A dark picture may still be 
incorrectly adjusted. Use a bright picture when adjusting.
   For a video signal and s-video signal
The video format best suited for the respective input signal will be selected 
automatically. This function is available only when the AUTO is selected for 
the VIDEO FORMAT item in the INPUT menu (
40). The vertical position and 
horizontal position will be automatically set to the default.
●  The automatic adjustment operation requires approx. 10 seconds. Also please  note that it may not function correctly with some input. 
●  When this function is performed for a video signal, a certain extra such as a line  may appear outside a picture.
●  When this function is performed for a computer signal, a black frame may be  displayed on the edge of the screen, depending on the PC model. 
●  
The items adjusted by this function may vary when the FINE or DISABLE is selected 
for the AUTO ADJUST item of the SERVICE item in the OPTION menu (
61).
    For a component video signal 
The vertical position and horizontal position will be automatically set to the default. 
The horizontal phase will be automatically adjusted.
AUTO button
VIDEODOC.CAMERA
KEYSTONE
ASPECT
SEARCHBLANK
MUTE
MY BUTTON
POSITION ESC MENU
RESET
COMPUTER MY SOURCE/
AUTOMAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
ー
＋VOLUME
1 2
ENTER
VIDEODOC.CAMERA
KEYSTONE
ASPECT
SEARCHBLANK
MUTE
MY BUTTON
POSITION ESC MENU
RESET
COMPUTER MY SOURCE/
AUTOMAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
ー
＋VOLUME
1 2
ENTER1.Press the POSITION
 button on the remote control while no menu 
is on screen, to display the D-SHIFT 
(43) dialog on screen.
2.Use the ▲, ▼, ◄ and ► buttons to adjust the picture position.
Press the POSITION  button again to fi nish this operation.
●  This is a function to shift the position of the shrunken picture by the D-ZOOM 
( 43) 
function.
●  When an OSD (On Screen Display) menu is displayed, this operation moves the  position of the OSD menu, but not the position of the picture  
(30).
●  The D-SHIFT adjustment values are not valid when the D-ZOOM is set to 256 (full  screen). (CP-D27WN/CP-D32WN)
●  The D-SHIFT adjustment values are not valid when the D-ZOOM is set to 320 (full  screen). (CP-DW25WN)
POSITION  button
Adjusting the position 
						

							26
Operating
1.
Correcting the keystone distortions
2.
KEYSTONE button
VIDEODOC.CAMERA
KEYSTONE
ASPECTSEARCHBLANK
MUTE
MY BUTTON
POSITION ESC MENU
RESET
COMPUTER MY SOURCE/
AUTOMAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
ー
＋VOLUME
1 2
ENTER
Press the KEYSTONE button on the remote control. 
A dialog will appear on the screen to aid you in correcting the 
distortion.
Use the ◄/► cursor buttons for adjustment.
To close the dialog and complete this operation, press the 
KEYSTONE button again. Even if you do not do anything, the 
dialog will automatically disappear after about ten seconds.
●  The adjustable range of this function varies for each input signal. For some input,  this function may not work well.
●  When the projector is inclined to near ±6 degrees or over, this function may not  work well.
●  This function will be unavailable when the TRANSITION DETECTOR is activated  (
82).
●  The OSD menu might be displayed outside of the image display area depending  on the adjustment value of the ASPECT, D-ZOOM and 
KEYSTONE. Changing 
the values of ASPECT, D-ZOOM and 
KEYSTONE may fi x the symptom. 
						

							27
VIDEODOC.CAMERA
KEYSTONE
ASPECTSEARCHBLANK
MUTE
MY BUTTON
POSITION ESC MENU
RESET
COMPUTER MY SOURCE/
AUTOMAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
ー
＋VOLUME
1 2
ENTER
Operating
1.
Using the magnify feature
2.
3.
4.
Press the MAGNIFY ON button on the remote control. 
The picture will be magnifi ed, and the MAGNIFY dialog will 
appear on the screen. When the 
MAGNIFY ON button is 
pressed for the fi rst time after the projector is turned on, the 
picture will be zoomed by 1.5 times. On the dialog, triangle 
marks to show each direction will be displayed.
The display magnifi cation of the projector switches in order 
with every press of the MAGNIFY ON button.
   For computer signals, HDMI
TM (RGB) signals, input signals from the 
LAN, USB TYPE A or USB TYPE B port
      1.5 times   2 times  3 times  4 times  1 time 
  
For video signals, s-video signals, component video signals or HDMITM 
(Component) signals
      1.5 times   2 times   1 time 
While the triangles are displayed on the dialog, use the ▲/▼/◄/► cursor 
buttons to shift the magnifying area.
Press the MAGNIFY OFF  button on the remote control to exit magnifi cation.
●  The MAGNIFY dialog will automatically disappear in several seconds with no 
operation. The dialog will appear again if the  MAGNIFY ON button is pressed 
when the dialog has automatically disappeared.
●   The magnifi cation is automatically disabled when the displaying signal or its 
display condition is changed.
●   While the magnifi cation is active, the keystone distortion condition may vary. 
It will be restored when the magnifi cation is disabled.
●   Some horizontal stripes might be visible on the image while magnifi  cation is 
active.
●   This function is not available in the following cases: 
-  A sync signal in the range not supported is input.
-  There is no input signal.
MAGNIFY
ON/OFF  button 
						

							28
Operating
1.Press BLANK button on the remote control. 
The BLANK screen will be displayed instead of the screen of 
input signal. Please refer to BLANK item in SCREEN menu 
(
50).
To exit from the BLANK screen and return to the input signal 
screen, press BLANK button again. 
Temporarily blanking the screen
●  The projector automatically exits from the BLANK mode when 
some control buttons are pressed.
• The sound is not connected with the BLANK screen function. If 
necessary, set the volume or mute fi rst. To display the BLANK screen and mute 
the sound at one time, use AV MUTE function 
(60).
NOTE
1.Press the FREEZE button on the remote control. 
The “FREEZE” indication will appear on the screen (however, 
the indication will not appear when the OFF is selected for 
the MESSAGE item in the SCREEN menu (
52)), and the 
projector will go into the FREEZE mode, which the picture is 
frozen.
To exit the FREEZE mode and restore the screen to normal, 
press the FREEZE button again. 
Temporarily freezing the screen
●  The projector automatically exits from the FREEZE mode when some control 
buttons are pressed.
●  If the projector continues projecting a still image for a long time, the LCD  panel might possibly be burned in. Do not leave the projector in the FREEZE 
mode for too long.
●  Images might appear degraded when this function is operated, but it is not a  malfunction.
►If you wish to have a blank screen while the projector’s lamp 
is on, use the BLANK function above.
Taking any other action may cause the damage on the projector. CAUTION
FREEZE button
VIDEODOC.CAMERA
KEYSTONE
ASPECT
SEARCHBLANK
MUTE
MY BUTTON
POSITION ESC MENU
RESET
COMPUTER MY SOURCE/
AUTOMAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
ー
＋VOLUME
1 2
ENTER
BLANK button
VIDEODOC.CAMERA
KEYSTONE
ASPECT
SEARCHBLANK
MUTE
MY BUTTON
POSITION ESC MENU
RESET
COMPUTER MY SOURCE/
AUTOMAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
ー
＋VOLUME
1 2
ENTER 
						

							29
VIDEODOC.CAMERA
KEYSTONE
ASPECTSEARCHBLANK
MUTE
MY BUTTON
POSITION ESC MENU
RESET
COMPUTER MY SOURCE/
AUTO
MAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
ー
＋VOLUME
1
2
ENTER
FOCUS-
+D-ZOOM-
+
Operating
1.To start the MENU, press the MENU button. The MENU you last used (EASY 
or ADVANCED) will appear. EASY MENU has priority to appear just after 
powered on.
Using the menu function
2.(1)  Use the ▲/▼ cursor buttons to select an item to 
operate. If you want to change it to the ADVANCED 
MENU, select the ADVANCED MENU.
(2)  Use the ◄/► cursor buttons to operate the item.
This projector has the following menus: 
PICTURE, IMAGE, INPUT, SETUP, AUDIO, SCREEN, OPTION, NETWORK, 
SECURITY and EASY MENU. 
EASY MENU consists of functions often used, and the other menus are classifi ed 
into each purpose and brought together as the ADVANCED MENU.
Each of these menus is operated using the same methods. 
While the projector 
is displaying any menu, the  MENU button on the projector works as the cursor 
buttons.  The basic operations of these menus are as follows.
In the EASY MENU
(continued on next page) (1)  Use the ▲/▼ cursor buttons to select a menu.
If you want to change it to the EASY MENU, 
select the EASY MENU.
The items in the menu appear on the right side.
(2)  Press the ► cursor button or ENTER button to  move the cursor to the right side. Then use the 
▲/▼ cursor buttons to select an item to operate and press the ► cursor 
button or ENTER button to progress. The operation menu or dialog of the 
selected item will appear.
(3)  Use the buttons as instructed in the OSD to operate the item.
In the ADVANCED MENU
MENU button 
(Cursor buttons)
VIDEODOC.CAMERA
KEYSTONE
ASPECT SEARCHBLANK
MUTE
MY BUTTONPOSITION ESC MENU
RESET
COMPUTER MY SOURCE/AUTOMAGNIFYPAGEDOWNONOFFFREEZEUPー＋VOLUME
1 2
ENTER
RESET button
ENTER button
MENU button
Cursor buttons
ESC button 
						

							30
Operating
Using the menu function (continued)
3.To close the MENU, press the MENU button again or select EXIT and press 
the ◄ cursor button or ENTER button. Even if you do not do anything, the 
dialog will automatically disappear after about 30 seconds.
●  If you want to move the menu position, use the cursor buttons after pressing the 
POSITION button.
●   Some functions cannot be performed when a certain input port is selected, or 
when a certain input signal is displayed.
●   When you want to reset the operation, press  RESET button on the remote 
control during the operation. Note that some items (ex. LANGUAGE, VOLUME) 
cannot be reset.
●   In the ADVANCED MENU, when you want to return to the previous display, 
press the ◄ cursor button or ESC button on the remote control.
Indication in OSD (On Screen Display)
The meanings of the general words on the OSD are as follows.
Indication Meaning
EXITSelecting this word finishes the OSD menu. It's the same as 
pressing the 
MENU button.
RETURN Selecting this word returns the menu to the previous menu.
CANCEL or NO Selecting this word cancels the operation in the present 
menu and returns to the previous menu.
OK or YES Selecting this word executes the prepared function or shifts 
the menu to the next menu.