Hitachi Projector CP-D27WN User Manual

							61
OPTION menu
ItemDescription
SERVICE Selecting this item displays the SERVICE 
menu.
Select an item using the ▲/▼ buttons, and 
press the ► button or the ENTER button 
on the remote control to execute the item.
ALTITUDE
Using the ▲/▼ buttons switches the rotation speed of the cooling 
fans. If the projector is used at an altitude of about 1600 m or higher, 
select HIGH. Otherwise, select NORMAL. Note that the projector is 
noisier when the HIGH is selected.
HIGH  ó NORMAL
AUTO ADJUST
Using the ▲/▼ buttons to select one of the mode. When the 
DISABLE is selected, the automatic adjustment feature is disabled.
FINE  ó FAST 
ó DISABLE
   
FINE: Finer tuning including H.SIZE adjustment.
FAST :  Faster tuning, setting H.SIZE to prearranged data for the 
input signal.
• Depending on conditions, such as input image, signal cable to 
the projector, environment around the projector, etc., the automatic 
adjustment may not work correctly.  In such a case, please 
choose DISABLE to disable the automatic adjustment, and make 
adjustment manually.
GHOST
Adjust the settings using the ▲/▼ buttons to eliminate ghosting.
FILTER MESSAGE
Use the ▲/▼ button to set the timer for notifying by the message 
when to replace the filter unit  100h  ó • • • 
ó 5000h 
ó OFF
After choosing an item except OFF, the message “REMINDER *** 
HRS PASSED ....” will appear after the timer reaches the interval 
time set by this feature (
 109). 
When the OFF is chosen, the message will not appear. Utilize this 
feature to keep the air filter clean, setting the suitable time according 
to your environment of this projector.
• Please take care of the filter unit periodically, even if there is 
no message. If the air filter becomes to be blocked by dust or 
other matter, the internal temperature will rise, which could cause 
malfunction, or reduce the lifetime of the projector.
• Please be careful with the operating environment of the projector 
and the condition of the filter unit.
(continued on next page) 
						

							62
OPTION menu
ItemDescription
SERVICE
(continued) KEY LOCK
(1)  
Use the ▲/▼ buttons to select CONTROL PANEL or REMOTE 
CONTROL.
(2) Use the ◄/► buttons to turn the key lock function on/off.
When ON is selected, all buttons on the projector or remote control 
except the STANDBY/ON button are locked.
• Please use this function to prevent tampering or accidental 
operation. 
• It is not possible to set both CONTROL PANEL and REMOTE 
CONTROL to ON.
REMOTE FREQ.
(1)   Use the ▲/▼ button to change the projector's remote sensor 
frequency setting  (
17, 18).
1:NORMAL  ó 2:HIGH
(2)   Use the ◄/► button to change the 
projector's remote sensor on or off.
ON  ó OFF
The factory default setting is for both 1:NORMAL and 2:HIGH to be 
on. If the remote control does not function correctly, disable either of 
them.
It's not possible to disable both options at the same time.
COMMUNICATION
Selecting this item displays COMMUNICATION 
menu. 
In this menu, you can configure the serial 
communication settings of the projector using the 
CONTROL port.
• Select an item using the cursor buttons ▲/▼. 
Then pressing the ► button opens the submenu 
for the setting item you selected. Or, pressing 
the ◄ button instead of the ► button makes the 
menu back to the previous one without changing 
the setup. Each submenu can be operated as 
described above.
• When COMMUNICATION TYPE (
 63) is set to 
OFF, the other items in COMMUNICATION menu 
are invalid. 
• For the function of serial communication, refer 
to the User's Manual - Network Guide .
(continued on next page) 
						

							63
OPTION menu
ItemDescription
SERVICE
(continued)
COMMUNICATION (continued)
COMMUNICATION TYPE
Select the communication type for transmission via 
the CONTROL port.
NETWORK BRIDGE: 
Select this type, if it is required 
to control an external device as a network terminal, 
via this projector from the computer. 
The CONTROL port doesn't accept RS-232C  
commands (
 Network Bridge Function
 in the 
User’s Manual - Network Guide)
OFF : Select this mode to receive RS-232C 
commands using the  CONTROL port. 
• 
OFF is selected as the default setting. 
• When you select the NETWORK BRIDGE, check 
the item, TRANSMISSTION METHOD  (
below).
SERIAL SETTINGS
Select the serial communication condition for the 
CONTROL port. BAUD RATE 4800bps  ó 9600bps 
ó 19200bps 
ó 38400bps
      
 PARITY
NONE  ó ODD 
ó EVEN
    
• The BAUD RATE is fixed to 19200bps and PARITY 
is fixed NONE when the COMMUNICATION TYPE 
is set to OFF
 ( above).
TRANSMISSION METHOD
Select the transmission method for communication by 
the NETWORK BRIDGE from the CONTROL port.
HALF-DUPLEX 
ó FULL-DUPLEX
HALF-DUPLEX : This method lets the projector 
make two way communication, but only one 
direction, either transmitting or receiving data, is 
allowed at a time.
FULL-DUPLEX : This method lets the projector 
make two way communication, transmitting and 
receiving data at the same time.
• HALF-DUPLEX is selected as the default setting.
• If you select HALF-DUPLEX, check the setting of 
the item RESPONSE LIMIT TIME  (
64).
(continued on next page) 
						

							64
OPTION menu
ItemDescription
SERVICE
(continued)
COMMUNICATION (continued)
RESPONSE LIMIT TIME
Select the time period to wait for receiving 
response data from other device communicating by 
the NETWORK BRIDGE and the HALF-DUPLEX 
through the CONTROL port.
OFF  ó 1s 
ó 2s 
ó 3s
    
OFF : Select this mode if it is not required to check 
the responses from the device that the projector 
sends data to. In this mode, the projector can 
send out data from the computer continuously.
1s /2s /3s: Select the time period to keep the  projector waiting for response from the device 
that the projector sends data to. While waiting the 
response, the projector does not send out any 
data from the CONTROL port.
• This menu is available only when the NETWORK 
BRIDGE is selected for the COMMUNICATION 
TYPE and the HALF-DUPLEX is selected for the 
TRANSMISSION METHOD  (
63).
• OFF is selected as the default setting.
CLONING
The setttings of the projector can be coppied via USB 
memory.
SAVE:  Saves each settings of the projector to USB 
memory.
LOAD: 
Loads each settings of the projector from 
USB memory. Message will be displayed 
after loading, and power will turn off after five 
min. or by pressing ► button. (A message is 
displayed for a few seconds if loading fails.) 
After saving / loading, you can remove the USB 
storage device.
(continued on next page) 
						

							65
OPTION menu
ItemDescription
SERVICE
(continued)
CLONING(continued)
The following items are exempted.
OPTION: LAMP TIME, FILTER TIME, 
SERVICE(GHOST)
NETWORK: WIRELESS AND WIRED SETUP (IP ADDRESS, SUBNET MASK, 
DEFAULT GATEWAY, DATE AND 
TIME), MY IMAGE, PRESENTATION
SECURITY: MY TEXT DISPLAY
• Operation is not available if SECURITY_
CLONING LOCK is turned ON.
• The Screen_MyScreen can only be loaded.
CLONING load function on STANDBY MODE
• While the projector is in STANDBY MODE, push 
the INPUT button of control panel together with  ► 
button, and then press ▲ button to start operating 
the CLONING load function.
• During loading process, the three indicators of 
control panel (POWER (orange), TEMP, LAMP) 
will remain on.
•    After the loading process, the three indicators 
(POWER (orange), TEMP, LAMP) will turn off. 
Then, you can remove the USB storage device.
•   If the loading fails, the three indicators (POWER 
(orange), TEMP, LAMP) will blink at the same 
time.
• CLONING is invalid with the following conditions.
- CLONING LOCK is turned ON. 
    With this condition, the three indicators (POWER 
(orange), TEMP, LAMP) will blink at approximately 
three seconds intervals.
- If the STANDBY MODE is set to SAVING.
-   If there is no USB memory inserted into USB 
TYPE A port.
-   If PIN LOCK or lock of TRANSITION DETECTOR 
is not being released.
- If a system error occurs.
• Please operate one of the following after loading.
-   Press INPUT button and 
◄ button of the control 
panel at the same time.
- Wait at least five min. after loading. 
-   Restart the projector after re-plugging the AC 
cable.
(continued on next page) 
						

							66
OPTION menu
ItemDescription
SERVICE
(continued)
CLONING(continued)
Load MyScreen data
•   Please save the image data as "pj_logo.bmp" or 
"pj_logo.gif" into USB memory.
•   Please note that the only compatible formats are 
as follows.
-File format Windows BMP    bit/pixel: 2/4/8/15/16/24/32bit
Compression format : 
Without compression/RLE
GIF
-Image size: more than 36x36, less than 1280x800
•   If two kinds of file format are saved, "pj_logo.
bmp" will be registered into MyScreen data.
•   If MyScreen LOCK or MyScreen PASSWORD 
is turned ON, the data of MyScreen cannot be 
loaded.
Setting the data
•   Operating the SAVE function under CLONING 
will name the file as "pj_data.bin" into the USB 
memory. Please do not attempt to change the file 
name or the folder structure.
•   If a file with the same name already exists, it will 
be overwritten by operating the SAVE function.
Loading function
•   Please note that saved data from other model 
cannot be loaded.
•   Please note that, if any of the following 
functions: MyScreen PASSWORD, PIN 
LOCK, TRANSITION DETECTOR, MY TEXT 
PASSWORD under SECURITY menu or 
MyScreen Lock under SCREEN menu is ON, the 
respective saved data cannot be loaded.
(continued on next page) 
						

							67
OPTION menu
ItemDescription
SERVICE
(continued) CLONING
(continued)
Loading function  (continued)
•   Please note that the saved data of KEYSTONE 
under SETUP menu cannot be loaded if 
TRANSITION DETECTOR under SECURITY 
menu is ON.
•   Please note that the saved data of START UP 
and MyScreen Lock under SCREEN menu 
cannot be loaded if MyScreen PASSWORD 
under SECURITY menu is ON.
•   Please note that the saved data of MY TEXT 
WRITING cannot be loaded if MY TEXT 
PASSWORD under SECURITY menu is ON.
INFORMATION
Selecting this item displays a dialog titled “INPUT_INFORMATION”. 
It shows the information about the current input.
• The “FRAME LOCK” message on the dialog means the frame lock 
function is working. 
• This item can't be selected for no signal and sync out.
• When the MY TEXT DISPLAY is set to ON, the MY TEXT is 
displayed together with the input information in the INPUT_
INFORMATION box (
 84).
FACTORY RESET
Selecting OK using the ► button performs this function. By this 
function, all the items in all of menus will collectively return to the 
initial setting. Note that the items LAMP TIME, FILTER TIME, 
LANGUAGE, FILTER MESSAGE, NETWORK and SECURITY 
settings are not reset. CANCEL  ð OK
Be sure to set ALTITUDE after resetting all the settings (
 61). 
						

							68
NETWORK menu
Remember that incorrect network settings on this 
projector may cause trouble on the network. Be sure 
to consult with your network administrator before 
connecting to an existing access point on your network.
Select “NETWORK” from the main menu to access the 
following functions. 
Select an item using the ▲/▼ cursor buttons on the 
projector or remote control, and press the ► cursor button on the projector or 
remote control, or ENTER button on the remote control to execute the item. Then 
perform it according to the following table. See the Network Guide for details of 
NETWORK operation.
NETWORK menu
• To use the wireless network function of this projector, the designated
USB wireless adapter that is sold as an option is required. Do not use 
any extension cable or device when connecting the adapter to the projector .
• 
The projector does not allow both wireless and wired LAN to be connected to 
the same network. 
• Do not set the same network address for both wireless and wired LAN.
• If you are not utilizing SNTP (Date/Time Settings in the Network Guide) , 
then you must set the DATE AND TIME during the initial installation.
• The network communication control is disabled while the projector is in 
standby mode if the STANDBY MODE item of SETUP menu is set to SAVING. 
Please connect the network communication to the projector after setting the 
STANDBY MODE to NORMAL (
46).
NOTE
Item
Description
WIRELESS  SETUP Selecting this item displays the WIRELESS 
SETUP menu for the wireless LAN.
Use the ▲/▼ buttons to select an item, 
and the ► or ENTER button on the remote 
control to perform the item.
MODE Use the ▲/▼ buttons to select the mode of the 
network communication system. Select according 
to the settings of your computer.
AD  HOC 
ó INFRASTRUCTURE
To save the setting, press the ► button.
• When ADHOC is selected, IEEE802.11 n cannot 
be used.
• If ADHOC is set to MODE while one of WPA-
PSK or WPA2-PSK is selected in ENCRYPTION, 
the ENCRYPTION (
 70) setting switches to OFF 
automatically.
(continued on next page) 
						

							69
NETWORK menu
ItemDescription
WIRELESS  SETUP
(continued) DHCP  
(Dynamic Host  Configuration  Protocol) Use the ▲/▼ buttons to turn DHCP on/off.
ON  ó OFF
Select OFF when the network does not have DHCP 
enabled. To save the setting, press the ► button.
• When the “DHCP” setting changes to “ON”, it 
takes a little time to obtain IP address from DHCP 
server.
• Auto IP function will be assigned an IP address if 
the projector could not obtain an IP address from 
server even if DHCP is “ON”
IP ADDRESS Use the ▲/▼
/◄/► buttons to enter the IP 
ADDRESS. 
This function can only be used when DHCP is set 
to OFF.
• The IP ADDRESS is the number that identifies 
this projector on the network. You cannot have two 
devices with the same IP ADDRESS on the same 
network.
• The IP ADDRESS “0.0.0.0” is prohibited.
SUBNET  MASK Use the ▲/▼
/◄/► buttons to enter the same 
SUBNET MASK used by your computer. 
This function can only be used when DHCP is set 
to OFF.
•  The SUBNET MASK “0.0.0.0” is prohibited.
DEFAULT 
GATEWAY Use the ▲/▼
/◄/► buttons to enter the DEFAULT 
GATEWAY (a node on a computer network that 
serves as an access point to another network) 
address.
This function can only be used when DHCP is set 
to OFF.
DNS SERVER Use the ▲/▼/
◄/► buttons to input the DNS 
server address. 
The DNS server is a system to control domain 
names and IP addresses on the Network. 
TIME 
DIFFERENCE Use the ▲/▼
 buttons to enter the TIME 
DIFFERENCE. 
Set the same TIME DIFFERENCE as the one 
set on your computer. If unsure, consult your IT 
manager. 
Use the ► button to return to the menu after 
setting the TIME DIFFERENCE.
• When this item is set, the same item in the 
WIRED SETUP menu is overwritten with the same 
setting (
 74). 
(continued on next page) 
						

							70
NETWORK menu
ItemDescription
WIRELESS  SETUP
(continued) DATE AND 
TIME Use the ▲/▼/◄/► buttons to enter the Year (last 
two digits), Month, Date, Hour and Minute.
• When this item is set, the same item in the 
WIRED SETUP menu is overwritten with the same 
setting (

74). 
• The projector will override this setting and retrieve 
DATE AND TIME information from the Time server 
when SNTP is enabled.  (Date/Time Settings in 
the Network Guide )
•  This setting will be reset if the projector is turned 
off while STANDBY MODE in the SETUP menu 
is set to SAVING (
 46), or when the AC power is 
turned off.
CH Use the ▲/▼ buttons to select the channel of the 
wireless LAN to be used while MODE 
(
68) is set 
to ADHOC. Select according to the settings of your 
computer.
The channels 1 to 11 are available. To save the 
setting, press the ► button.
• The available channels would be various 
depending on a country. In addition, wireless 
network card might be required due to the 
standard.
• This item can only be selected when MODE 
is set to ADHOC. When MODE is set to 
INFRASTRUCTURE, the channel is automatically 
selected.
ENCRYPTION Use the ▲/▼ buttons to select the encryption 
method to be used.
   WPA2-PSK(AES)   ó  WPA2-PSK(TKIP)  
                                                    
 
        OFF                             WPA-PSK(AES) 
                                                    
 
WEP 64bit óWEP 128bit
óWPA-PSK(TKIP)
To save the setting, press the ► button.
• When MODE (
 68) is set to ADHOC, either 
WPA-PSK and WPA2-PSK cannot be selected.
• If IEEE802.11 n is used while MODE is set to 
INFRASTRUCTURE, TKIP and WEP are disabled. 
• If OFF or AES is not selected, communication will 
switch automatically to IEEE802.11 b/g.
(continued on next page)