Hitachi Projector CP-D27WN User Manual

							11
Connecting with your devices (continued)
•   When  AUTO  is  selected  for  the  COMPUTER  IN1  or COMPUTER  IN2  port  in 
COMPUTER  IN  of  the  INPUT  menu,  that  port  will  accept  component  video 
signals  (
41).
•  
When  the  USB  TYPE  B  port  and  the  computer's  type A  USB  port  are  connected, 
you  can  use  the  USB  TYPE  B  port  as  a  picture  input  port  from  the  computer,  or 
use the remote control as a simple mouse and keyboard of the computer. (
 18).
Setting up
(continued on next page)
• Plug-and-Play is a system composed of a computer, its operating system 
and peripheral equipment (i.e. display devices). This projector is VESA DDC 
2B compatible. Plug-and-Play can be used by connecting this projector to a 
computer that is VESA DDC (display data channel) compatible.
-   Take advantage of this feature by connecting a computer cable to the 
COMPUTER IN1 port (DDC 2B compatible). Plug-and-Play may not work 
properly if any other type of connection is attempted.
-  
Please use the standard drivers in your computer as this projector is a Plug-and-
Play monitor.
About Plug-and-Play capability
COMPONENTCb/PbY
Cr/Pr
HDMI
R L
VIDEO
S-VIDEO
AUDIO
OUT
AUDIOOUT
USB
(A) DISPLAY
RS-232C
HDMI
VCR/DVD/Blu-ray Disc
playerComputer 
						

							12
Connecting with your devices (continued)
(continued on next page)
• Before connecting the projector to a computer, consult the computer’s 
manual and check the compatibility of the signal level, the synchronization 
methods and the display resolution output to the projector. 
-   Some signal may need an adapter to input this projector.
-   Some computers have multiple screen display modes that may include some 
signals which are not supported by this projector.
-    Although the projector can display signals with resolution up to UXGA   
(1600X1200), the signal will be converted to the projector’s panel resolution 
before being displayed. The best display performance will be achieved if the 
resolutions of the input signal and the projector panel are identical.
•   If you connect this projector to a notebook computer, you need to output the 
display to an external monitor, or output simultaneously to the internal display 
and an external monitor. Consult the computer's manual for the setting.
•   Depending on the input signal, the automatic adjustment function of this 
projector may take some time and not function correctly. 
-   Note  that  a  composite  sync  signal  or  sync-on-green  signal  may  confuse  the 
automatic adjustment function of this projector  (
41). 
-   If the automatic adjustment function does not work correctly, you may not see 
the dialog to set the display resolution.  In such a case, use an external display 
device.  You  may  be  able  to  see  the  dialog  and  set  an  appropriate  display 
resolution.
NOTE
Setting up 
						

							13
(continued on next page) Connecting with your devices (continued)
Setting up
•  If you insert a USB storage device, such as a USB memory, into the USB TYPE 
A port and select the port as the input source, you can view images stored in the 
device (
85).
•    You can connect a dynamic microphone to the  MIC port with a 3.5 mm mini-plug. 
In that case, the built-in speaker outputs the sound from the microphone, even 
while the sound from the projector is output. You can input line level signal to the 
MIC port from equipment such as wireless microphone. Select HIGH in the MIC 
LEVEL item of the AUDIO menu when you input line level audio signal to the 
MIC port. In the normal mode, the volume of the microphone can be adjusted 
separately from the volume of the projector using the menu.  (
49)  
    In the standby mode, the volume of the microphone is adjustable with the 
VOLUME +/-  buttons on the remote control, in synchronization with the volume 
of the projector. (
21)   
    Even when the sound of projector is set to mute mode by the AUDIO SOURCE 
function (
48), the volume of the microphone is adjustable.  
    In both modes (standby or normal), the  MUTE button on the remote control 
works on the sounds of the microphone and the projector. (
21)
• If a loud feedback noise is produced from the speaker, move the 
microphone away from the speaker. 
•  This projector doesn't support plug-in power for the microphone.
NOTE
Monitor
R
LRGB IN
Microphone system
Speakers(with an amplifier) 
						

							14
Setting up
USB storage device
Connecting with your devices  (continued)
To use network functions of the projector, connect the LAN port with the 
computer's LAN port, or with an access point that is connected to the computer 
with wireless LAN, using a LAN cable. To use NETWORK BRIDGE function, 
also connect the  CONTROL port and an RS-232C port of the external device to 
communicate as a network terminal. See the  User's Manual - Network Guide for 
details of the network functions.
►Before connecting the projector to a network system, be sure 
to obtain the consent of the administrator of the network.
►
Do not connect the LAN port to any network that might have the excessive voltage.
►The designated USB wireless adapter that is sold as an option is required to 
use the wireless network function of this projector.
►Before removing the USB storage device from the port of the projector , be 
sure to use the REMOVE USB function on the thumbnail screen to secure your 
data (
88).
►Do not use any extension cable or device when connecting the adapter to 
the projector. Before you insert or pull out the USB wireless adapter from the 
projector, turn off the power of the projector and pull out the power cord’s plug 
from the outlet. Do not touch the USB wireless adapter while the projector is 
receiving AC power.
►To connect both the LAN cable and USB device to the projector, use a LAN 
cable that is fl at on the side where the plug’s wire is visible. Otherwise, both of 
them cannot be connected correctly, or the wire may break (malfunction). CAUTION
RS-232CLANUSB TYPE ARS-232C
Access pointComputer
(continued on next page)
USB 
wireless  adapter
(optional)
External 
Device 
						

							15
• If an oversized USB storage device blocks the LAN port, use a USB 
extension cable to connect the USB storage device.
• The HDMI port of this model is compatible with HDCP (High-bandwidth Digital 
Content Protection) and therefore capable of displaying a video signal from 
HDCP compatible DVD players or the like.
- The HDMI supports the following signals.
Video signal : 480i@60, 480p@60, 576i@50, 576p@50, 720p@50/60, 
1080i@50/60, 1080p@50/60
Audio signal : Format Linear PCM
Sampling frequency 48kHz / 44.1kHz / 32kHz
- This projector can be connected with another equipment that has HDMI
TM 
connector, but with some equipment the projector may not work properly, 
something like no video.
- Be sure to use an HDMI
TM cable that has the HDMITM logo.
- Use a Category 2-certified HDMITM cable to input 1080p@50/60 signal to the 
projector.
- When the projector is connected with a device having DVI connector , use a 
DVI to HDMI
TM cable to connect with the HDMI input.
• Up to one USB wireless adapter (optional) can be connected to a projector .
NOTE
Setting up
Connecting with your devices
 (continued) 
						

							16
Setting up
Connecting to a power supply
1.Put the connector of the power cord into the 
AC IN (AC inlet) of the projector.
2.Firmly plug the power cord’s plug into the 
outlet. In a couple of seconds after the 
power supply connection, the POWER 
indicator will light up in steady orange.
►Please use extra caution when connecting the power cord, as 
incorrect or faulty connections may result in fire and/or electrical shock.
• Do not touch the power cord with a wet hand.
• Only use the power cord that came with the projector. If it is damaged, consult 
your dealer to get a new one. Never modify the power cord. 
• Only plug the power cord into an outlet whose voltage is matched to the power 
cord. The power outlet should be close to the projector and easily accessible. 
Remove the power cord for complete separation.
• Do not distribute the power supply to multiple devices. Doing so may overload
the outlet and connectors, loosen the connection, or result in fire, electric shock
or other accidents. WARNING
Using the security bar and slot
A commercial anti-theft chain or wire up to 
10 mm in diameter can be attached to the 
security bar on the projector.
Also this product has the security slot for 
the Kensington lock. 
For details, see the manual of the security 
tool.
►Do not use the security bar and slot to prevent the projector 
from falling down, since it is not designed for it. WARNING
►Do not place anti-theft chain or wire near the exhaust vents. 
 
It may become too hot.  CAUTION
• 
The security bar and slot is not comprehensive theft prevention 
measures. It is intended to be used as supplemental theft prevention measure. NOTE
Please remember that when the DIRECT POWER 
ON function activated (
56), the connection of the 
power supply make the projector turn on.
AC IN Power cord
Security bar
Security slot
Anti-theft chain or wire 
						

							17
Remote control
Remote control
About the remote control signal
The remote control works with the projector’s remote 
sensor. This projector has a remote sensor on the front.
The sensor senses the signal within the following range 
when the sensor is active: 60 degrees (30 degrees to the left and right of the sensor) 
within about 3 meters.
Installing the batteries
Please insert the batteries into the remote control before using it. If the remote control 
starts to malfunction, try to replace the batteries. If you will not use the remote control for 
long period, remove the batteries from the remote control and store them in a safe place.
1.Holding the hook part of the battery 
cover, remove it.
2.Align and insert the two AA batteries 
(HITACHI MAXELL ENERGY,  
Part No.LR6 or R6P) according to their plus and minus terminals as indicated 
in the remote control.
3.Replace the battery cover in the direction of the arrow and snap it back into place.
►Always handle the batteries with care and use them only as 
directed. Improper use may result in battery explosion, cracking or leakage, 
which could result in fi re, injury and/or pollution of the surrounding environment.
• Be sure to use only the batteries specifi ed. Do not use batteries of different 
types at the same time. Do not mix a new battery with used one. 
• 
Make sure the plus and minus terminals are correctly aligned when loading a battery.
• Keep a battery away from children and pets.
• Do not recharge, short circuit, solder or disassemble a battery .
• 
Do not place a battery in a fi re or water. Keep batteries in a dark, cool and dry place.
• If you observe battery leakage, wipe out the leakage and then replace a battery. 
If the leakage adheres to your body or clothes, rinse well with water immediately .
• Obey the local laws on disposing the battery. WARNING
• The remote control signal refl ected in the screen or the like may be available. 
If it is diffi cult to send the signal to the sensor directly, attempt to make the signal refl ect.
• The remote control uses infrared light to send signals to the projector (Class 1 
LED), so be sure to use the remote control in an area free from obstacles that 
could block the remote control’s signal to the projector.
• 
The remote control may not work correctly if strong light (such as direct sun 
light) or light from an extremely close range (such as from an inverter fl uorescent 
lamp) shines on the remote sensor of the projector. Adjust the position of 
projector avoiding those lights.
NOTE
2
1 3
Remote 
sensor
30º30º
Approx.
3 m  
						

							18
Remote control
Changing the frequency of  remote control signal
The accessory remote control has the two choices on signal 
frequency Mode 1:NORMAL and Mode 2:HIGH. If the remote control 
does not function properly, attempt to change the signal frequency.
In order to set the Mode, please keep pressing the combination of 
two buttons listed below simultaneously for about 3 seconds.
Using as a simple PC mouse & keyboard
The accessory remote control works as a simple mouse 
and keyboard of the computer, when the projector’s USB 
TYPE B port and the computer’s type A USB port are 
connected and MOUSE is selected for the USB TYPE B 
item in the OPTION menu.
(1) PAGE UP key: Press PAGE UP button.
(2) PAGE DOWN key: Press PAGE DOWN button.
(3) Mouse left button: Press ENTER button.
(4) Move pointer: Use the cursor buttons ▲, ▼, ◄ and ►.
(5) ESC key: Press ESC button.
(6) Mouse right button:  Press RESET button.
►Improper use of the simple mouse & keyboard 
function could damage your equipment. While using this 
function, please connect this product only to a computer. Be 
sure to check your computer’s manuals before connecting this 
product to the computer.NOTICE
When the simple mouse & keyboard function of this product does not work 
correctly, please check the following.
• When a USB cable connects this projector with a computer having a built-in pointing 
device (e.g. track ball) like a laptop PC, open BIOS setup menu, then select the external 
mouse and disable the built-in pointing device, because the built-in pointing device may 
have priority to this function.
• 
Windows XP SP3 or higher is required for this function. And also this function may not work 
depending on the computer’s confi gurations and mouse drivers. This function can work with the 
computer which can operate general USB mouse or keyboard.
•  You cannot do things like press two buttons at once (for instance, pressing two buttons 
at the same time to move the mouse pointer diagonally).
• 
This function is activated only when the projector is working properly. This function is not 
available in any of the following cases:
- While the lamp is warming up. (The POWER indicator blinks in green.)
- When either USB TYPE A or USB TYPE B port is selected.
- While displaying BLANK 
(28), TEMPLATE (54) or MY IMAGE (76) screen.
- When any menu is displayed on the screen.
- 
While using the cursor buttons to operate the sound or screen functions such as adjusting the 
sound volume, correcting the keystone, correcting the picture position and magnifying the screen.
NOTE
(1) Set to Mode 1:NORMAL...  VOLUME - and RESET buttons 
(2) Set to Mode 2:HIGH...  MAGNIFY OFF and ESC buttons
Please remember that the REMOTE FREQ. in the SERVICE item of 
the OPTION menu
 (62) of the projector to be controlled should be 
set to the same mode as the remote control.
VIDEODOC.CAMERA
KEYSTONE
ASPECT SEARCHBLANK
MUTE
MY BUTTON
POSITION ESC MENU
RESET
COMPUTER MY SOURCE/
AUTOMAGNIFYPAGE
DOWNONOFF
FREEZEUP
ー＋VOLUME
1 2
ENTER
(1)(2)
VIDEODOC.CAMERA
KEYSTONE
ASPECT
SEARCHBLANK
MUTE
MY BUTTON
POSITION ESC MENU
RESET
COMPUTER MY SOURCE/
AUTOMAGNIFYPAGE
DOWNONOFF
FREEZEUP
ー＋VOLUME
1 2
ENTER
(1)
(3)
(5) (2)
(4)
(6)USB TYPE B  
port 
						

							19
Power on/off
1.Make sure that the power cord is firmly 
and correctly connected to the projector 
and the outlet.
Turning on the power
2.
3.
Power on/off
VIDEODOC.CAMERA
KEYSTONE
ASPECTSEARCHBLANK
MUTE
MY BUTTONPOSITION ESC MENU
RESET
COMPUTER MY SOURCE/AUTOMAGNIFYPAGEDOWNONOFFFREEZEUPー＋VOLUME
1
2
ENTER
FOCUS-
+D-ZOOM-
+
To display the picture, select an input signal according to the section Selecting an 
input signal
 (
21).
Make sure that the POWER indicator is 
steady orange (
110). Then, remove the 
lens cover.
Press the STANDBY/ON button on the 
projector or the remote control. The 
projection lamp will light up and the 
POWER indicator will begin blinking in 
green. When the power is completely on, 
the indicator will stop blinking and light in 
steady green (
110).
STANDBY/ON button
VIDEODOC.CAM ERA
KEYSTONEASPECT
SEARCHBLANK
MUTEMY BUTTONPOSITION ESC MENU
RESE T
COMPUTER MY SOURC
E/AUTOMAGNIFYPAGEDOWNONOFFFREEZEUPー＋VOLUME
1 2ENTER
POWER indicator
(continued on next page) The INITIAL SETTING Menu will be displayed by factory default upon startup. 
Once the INITIAL SETTING Menu is set, it will not appear until FACTORY RESET 
(
66) is executed. If you wish to change the settings, refer to the LANGUAGE 
(
50) and ALTITUDE (60) menu. 
(1)   LANGUAGE: Use the ▲/▼/◄/► 
buttons to select the desired language 
and press the ENTER button of the 
remote control or the INPUT button of 
the projector to execute.
(2)    ALTITUDE: Use the ▲/▼ buttons to 
select NORMAL for altitude below 
1600 m (5250 feet), otherwise select 
HIGH and press the ENTER button of 
the remote control or the INPUT button 
of the projector to execute. 
						

							20
Power on/off
►Do not touch around the lamp cover and the exhaust vents 
during use or just after use, since it is too hot.
►Remove the power cord for complete separation. The power outlet should be 
close to the projector and easily accessible. WARNING
1.Press the STANDBY/ON button on the projector or the remote control. 
 
The message “Power off?” will appear on the screen for about 5 seconds.
Turning off  the power
2.Press the STANDBY/ON button again while the message appears.   
The projector lamp will go off, and the POWER indicator will begin blinking in 
orange. Then POWER indicator will stop blinking and light in steady orange 
when the lamp cooling is complete (
110).
Do not turn the projector on for about 10 minutes or more after turning it of f. 
Also, do not turn the projector off shortly after turning it on. Such operations might 
cause the lamp to malfunction or shorten the lifetime of some parts including the lamp.
• Turn the power on/off in right order. Please power on the projector 
prior to the connected devices. 
• 
This projector has the function that can make the projector automatically turn on/
off. Please refer to the DIRECT POWER ON 
( 56) and AUTO POWER OFF ( 57) 
items of the OPTION menu.
NOTE
3.Attach the lens cover, after the  POWER indicator turns in steady orange.
WARNING  ►A strong light is emitted when the projector’s power is on. Do 
not look into the lens of the projector or look inside of the projector through any 
of the projector’s openings.
►Do not touch around the lamp cover and the exhaust vent during use or just 
after use, since it is too hot.
Turning on the power (continued)