Hitachi Cp-X5021n Projector Users Manual

41
INPUT menu
Item Description
COMPUTER INThe computer input signal type for COMPUTER IN1 and IN2 ports 
can be set.
(1)  
Use the ▲/▼ buttons to select the COMPUTER IN port to be set.
(2)  Use the ◄/► buttons to select 
the computer input signal type.
AUTO 
 SYNC ON G OFF
• Selecting the AUTO mode allows  
you to input a sync on G signal or component video signal from the 
port. Please refer to Technical for the connection of component 
video input to COMPUTER IN1/2 port.
• In the AUTO mode, the...

42
INPUT menu
Item Description
RESOLUTIONThe resolution for the COMPUTER IN1 and COMPUTER IN2 input 
signals can be set on this projector.
(1)  In the INPUT menu select the RESOLUTION using the ▲/▼ 
buttons and press the ► button. 
The RESOLUTION menu will be  
displayed.
(2)  In the RESOLUTION menu select the 
resolution you wish to display using 
the ▲/▼ buttons.  
Selecting AUTO will set a resolution 
appropriate to the input signal.
(3)  Pressing the ► or ENTER button when 
selecting a STANDARD...

43
SETUP menu
SETUP menu
From the SETUP menu, items shown in the table 
below can be performed.
Select an item using the ▲/▼ cursor buttons, and 
press the ► cursor button or ENTER button to 
execute the item. Then perform it according to the 
following table.
Item Description
AUTO KEYSTONE Selecting this item performs the Automatic keystone distortion 
correction. Projector automatically corrects vertical keystone 
distortion due to the (forward/backward) setup angle by itself.
This function will be...

44
SETUP menu
Item Description
 KEYSTONEUsing the ▲/▼ buttons corrects the vertical keystone distortion.
Shrink the top of the image 
 Shrink the bottom of the image.
• The adjustable range of this function will vary among inputs. For 
some input, this function may not work well.
• When the horizontal lens shift is not set to the center, this function 
may not work well.
• This function is unavailable when the TRANSITION DETECTOR 
(
74)  is ON or the screen is adjusted by PERFECT FIT (26).
PERFECT...

45
Item Description
STANDBY MODEUsing ▲/▼ buttons switches the standby mode setting between 
NORMAL and SAVING. 
NORMAL 
 SAVING
When SAVING is selected, the power consumption in the standby 
mode is lowered with some functional restriction as below:
• When SAVING is selected, the RS-232C communication control 
except to turn the projector on and the network function are disabled 
while the projector is in the standby mode. If the COMMUNICATION 
TYPE in the COMMUNICATION menu is set to NETWORK 
BRIDGE,...

46
AUDIO menu
AUDIO menu
From the AUDIO menu, items shown in the table below 
can be performed. Select an item using the ▲/▼ cursor 
buttons, and press the ► cursor button or the ENTER 
button to execute the item. Then perform it according to 
the following table.
Item Description
VOLUMEUsing the ◄/► buttons adjusts the volume.
Low 
 High
SPEAKERUsing the ▲/▼ buttons turns on/off the built-in speaker.
ON 
 OFF
When OFF is selected, the built-in speaker does not work.
AUDIO SOURCE
While the image signal...

47
AUDIO menu
Item Description
HDMI AUDIO
Using the ▲/▼ buttons switches the mode for the HDMI audio.
Check each of the two modes provided and select the suitable one 
for your HDMI audio device.
1 
 2
MIC LEVEL
Using the ▲/▼ buttons switches the input level to match that of the 
microphone connected to the MIC port.
HIGH 
 LOW
HIGH: for a microphone with an amplifier. 
LOW:  for a microphone without an amplifier.
MIC VOLUME
Using the ◄/► buttons adjusts the volume of the microphone 
connected to the MIC...

48
SCREEN menu
SCREEN menu
From the SCREEN menu, items shown in the table 
below can be performed.
Select an item using the ▲/▼ cursor buttons, and 
press the ► cursor button or ENTER button to 
execute the item. Then perform it according to the 
following table.
Item Description
LANGUAGEUsing the ▲/▼/◄/► buttons switches the OSD (On Screen 
Display) language.
ENGLISH 
 FRANÇAIS 
 DEUTSCH 
  ESPAÑOL
       
  (shown in the LANGUAGE dialog)  
Press the ENTER or INPUT button to save the language...

49
SCREEN menu
Item Description
MyScreenThis item allows you to capture an image for use as a MyScreen 
image which can be used as the BLANK screen and START UP 
screen. Display the image you want to capture before executing the 
following procedure.
1.  Selecting this item displays a dialog 
titled “MyScreen”. It will ask you if 
you start capturing an image from 
the current screen.
Please wait for the target image to be displayed, and press the 
ENTER or INPUT button when the image is displayed. The...

50
SCREEN menu
Item Description
MyScreen LockUsing the ▲/▼ buttons turns on/off the MyScreen lock function.
ON 
 OFF
When the ON is selected, the item MyScreen is locked. Use this 
function for protecting the current MyScreen.
• This function cannot be selected when the ON is selected to the 
MyScreen PASSWORD item in SECURITY menu (
72).
MESSAGEUsing the ▲/▼ buttons turns on/off the message function.
ON 
 OFF
When the ON is selected, the following message function works.
“AUTO IN PROGRESS” while...