Hitachi Cp-X5021n Projector Users Manual

11
Setting up
Connecting with your devices (continued)
Computer
(40)
(41)
(61)
(41)
(46)
(55)
• Before connecting the projector to a computer, consult the computer’s 
manual and check the compatibility of the signal level, the synchronization 
methods and the display resolution output to the projector. 
- 
 Some signal may need an adapter to input this projector.
- 
 Some computers have multiple screen display modes that may include some 
signals which are not supported by this projector.
-...

12
Setting up
Connecting with your devices (continued)
Computer
Access 
point
USB 
storage 
device
(64)
(78)
(64)
(55)
(61)
(continued on next page)
• If an oversized USB storage device blocks the LAN port, use a USB 
extension cable to connect the USB storage device.NOTE
► Before connecting the projector to a network system be sure 
to obtain the consent of the administrator of the network.
►Do not connect the LAN port to any network that might have the excessive 
voltage.
►Before removing the USB...

13
Setting up
(41)
(41)
(41)
(46)
VCR/DVD/Blu-ray Disc player Digital 
video 
device
• The HDMI port of this model is compatible with HDCP (High-band-
width Digital Content Protection) and therefore capable of displaying a video 
signal from HDCP compatible DVD players or the like.
- 
 The HDMI supports the following video signals: 
480i@60,480p@60,576i@50,576p@50,720p@50/60,1080i@50/60,1080p@50/60 
- 
 This projector can be connected with another equipment that has HDMI con-
nector, but with some...

14
Setting up
Speakers
(with an amplifier)
Wired 
remote 
control
(optional) Monitor
Microphone 
system
Connecting with your devices (continued)
• If a loud feedback noise is produced from the speaker, move the 
microphone away from the speaker. 
• This projector doesn't support plug-in power for the microphone. NOTE
• You can connect a dynamic microphone to the MIC port with a 3.5 mm mini-plug.
In that case, the built-in speaker outputs the sound from the microphone, even 
while the sound from the...

15
Connecting to a power supply
1.Put the connector of the power cord into the 
AC IN (AC inlet) of the projector.
2.Firmly plug the power cord’s plug into the 
outlet. In a couple of seconds after the 
power supply connection, the POWER 
indicator will light up in steady orange.
►Please use extra caution when connecting the power cord, as 
incorrect or faulty connections may result in fire and/or electrical shock.
•  Only use the power cord that came with the projector. If it is damaged, consult 
your...

16
30°3m30°
(approx.)
Remote control
About the remote control signal
The remote control works with the projector’s remote 
sensor. This projector has a remote sensor on the front.
The sensor senses the signal within the following range 
when the sensor is active:
60 degrees (30 degrees to the left and right of the sensor) 
within 3 meters about.
Installing the batteries
Please insert the batteries into the remote control before using it. If the remote control 
starts to malfunction, try to replace the...

17
Changing the frequency of  remote control signal
The accessory remote control has the two choices on signal 
frequency Mode 1:NORMAL and Mode 2:HIGH. If the remote control 
does not function properly, attempt to change the signal frequency.
In order to set the Mode, please keep pressing the combination of 
two buttons listed below simultaneously for about 3 seconds.
Using as a simple PC mouse & keyboard
The accessory remote control works as a simple mouse 
and keyboard of the computer, when the...

18
VIDEODOC
.
CAME
RA
KEYST
ONEASPEC
TSEA
RCH
BL
ANK
MUTEMY BUTTO
NPOSIT
IO
N1
2
E
SCENTERMENURE
SET
COMPUTE
RMY
 SOURCE/AUTOM
AGNIFYPAG
E
  
    UPVOLUM
EDOWNo ONOFF9× FR
EEZE
1.Make sure that the power cord is firmly and 
correctly connected to the projector and the 
outlet.
Turning on the power
2.Make sure that the POWER indicator is 
steady orange (
97). Then remove the lens 
cover.
3.Press STANDBY/ON button on the 
projector or the remote control.
The projection lamp will light up and POWER...

19
Operating
1.
Adjusting the volume
Use the VOLUME +/VOLUME - buttons to adjust the volume. 
A dialog will appear on the screen to aid you in adjusting the 
volume. If you do not do anything, the dialog will automatically 
disappear after a few seconds.
●  When  is selected for current picture input port, the volume adjustment is 
disabled. Please see AUDIO SOURCE item of AUDIO menu (
46).
●  Even if the projector is in the standby mode, the volume is adjustable when 
both of the following conditions...

20
VIDEODOC.CAMERA
KEYSTONE
ASPECT SEARCH
BLANK
MUTE
MY BUTTON
POSITION
12
MENU
COMPUTERMY SOURCE/
AUTO
MAGNIFYPAGE
      UPVOLUME
DOWNo ONOFF
9× FREEZE
1.Press VIDEO button on the remote control.  
Each time you press the button, the projector switches its 
input port from the current port as below. Selecting an input signal (continued)
●   While ON is selected for AUTO SEARCH item in OPTION 
menu, the projector will keep checking every port sequentially 
till an input signal is detected (
54). If...