Hitachi Cp-X308 Projector Users Manual



Setting up
Connecting your devices (continued)
• Be sure to read the manuals for devices before connecting them to the projector, and make sure that all the devices are suitable to be connected with this product. Before connecting to a PC, check the signal level, the signal timing, and the  resolution.-  Be sure to consult to the administrator of the network. Do not connect LAN port to any network that might have the excessive voltage.
-   Some signal may need an adapter to input this...



Setting up
Using a USB storage
Inserting the SD card
In order to view images stored in an SD storage, such as an SD memory card, insert the device into the SD card slot. Or, in order to use the wireless network function, load the internal clock battery (68) and insert the designated wireless network card into the SD card slot. 
In order to view images stored in a USB storage, such as a USB memory, insert the device into the USB STORAGE slot.Before removing the USB storage, be sure to...

3

Setting up
Connecting power supply
1.Put the connector of the power cord into the 
AC inlet of the projector.
2.Firmly plug the power cord’s plug into the 
outlet.
►Please use extra caution when connecting the power cord, as 
incorrect or faulty connections may result in fire and/or electrical shock.
• Only use the power cord that came with the projector. If it is damaged, contact 
your dealer to newly get correct one.
• Only plug the power cord into an outlet whose voltage is matched to the...

4

Remote control
Remote control
About the remote control signal
The remote control works with the projector’s remote 
sensor. This projector has a remote sensor on the front.
The sensor senses the signal within the following range 
when the sensor is active:
60 degrees (30 degrees to the left and right of the sensor) 
within 3 meters about.
Putting batteries
Please set the batteries to the remote control before using it. If the remote control starts 
to malfunction, try to replace the batteries....

5

Remote control
Changing the frequency of  remote control signal
The accessory remote control has the two choices on signal frequency Mode 1:NORMAL and Mode 2:HIGH. If the remote control does not function properly, attempt to change the signal frequency.In order to set the Mode, please keep pressing the combination of two buttons listed below simultaneously for about 3 seconds.
Using as a simple PC mouse & keyboard
The accessory remote control works as a simple mouse and keyboard of the PC, when...

6

Power on/off
1.Make sure that the power cord is firmly and correctly connected to the projector and the outlet.
Turning on the power
2.Remove the lens cover, and set the power switch to ON position (marked “ I ”). The POWER indicator will light up in steady orange (71). Then wait several seconds because the buttons may not function for these several seconds.
3.Press STANDBY/ON button on the projector or the remote control. The projection lamp will light up and POWER indicator will begin...

7

               COMPUTER IN 1  COMPUTER IN 2  MIU  
        VIDEO  S-VIDEO  COMPONENT (Y, Cb/Pb, Cr/Pr)
Operating
Operating
1.Press VOLUME button on the remote control. A dialog will appear on the screen to aid you in adjusting the volume.
Adjusting the volume
2.Use the ▲/▼ cursor buttons to adjust the volume. To close the dialog and complete the operation, press the VOLUME button again. Even if you do not do anything, the dialog will automatically disappear after a few seconds.
●  When  is...

8

Operating
1.Press VIDEO button on the remote control.  Each time you press the button, the projector switches its input port from the current port as below.
Selecting an input signal (continued)
●  
While TURN ON is selected for AUTO SEARCH item in OPTION menu, the projector will keep checking every port sequentially till an input signal is detected (42). If VIDEO button is pushed when COMPUTER IN1, COMPUTER IN2 or MIU port is selected, the projector will check COMPONENT port first. 
1.Press...

9

Operating
Adjusting the projector's elevator
When the place to put the projector is slightly uneven to the left or right, use the 
elevator feet to place the projector horizontally. 
Using the feet can also tilt the projector in order to project at 
a suitable angle to the screen, elevating the front side of the 
projector within 10 degrees.
This projector has 2 elevator feet and 2 elevator buttons. An elevator foot is adjustable 
while pushing the elevator button on the same side as it....

0

Operating
1.Press POSITION button on the remote control when no menu 
is indicated. 
The “POSITION” indication will appear on the screen.
Adjusting the position
2.Use the ▲/▼/◄/► cursor buttons to adjust the picture position.
When you want to reset the operation, press RESET button on 
the remote control during the operation.
To complete this operation, press POSITION button again. 
Even if you do not do anything, the dialog will automatically 
disappear after a few seconds.
●  
When this...