GTE Omni Si Database Technical Practices Manual

TL-130400-1001Table 4.5Entry Fields for Record Code OT (Continued)COMMENTS
Tone Duration000-255 = time
suggested valuetoneis heard.
-The camp-on tone alerts a called party that
a call is camped on.
-This time is in tenths of a second and the
d by the called party
/persons to whom the
000-255 = time
inhook trunk cal
queuing is used, thi
number of seconds
his time, the call is again placed in
72-75Maximum0160-2000 = timeThis field determines the maximum time
Hookswitchin millisecondsallowed for a...

TL-130400-1001Record Code OV:
Office Timing Values4.6 Record Code OV, Figure 4.6, defines the timing intervalsrequired for the call conditions. This data sheet is basically an
extension of the office timing values data sheet, Record Code OT
(Figure 4.5).
r---------Ir-----------------------T---T---T---T---T-----~-----------~---~-------~I
I
IT
I61 Ti T1 TIt T III T ;ITI
I
I615161I
I
I
I
I
I
I
iiI
I
I
Y.MII 
-I.1 .”
IIIIII
Figure 4.6 Record Code OV:Office Timing Values Data Sheet 

l-L-1 30400-l 00-l
Table 4.6Entry Fields for Record Code OVCOMMENTS
Hook Timeoutqueued to MERS, this field determines the
amount of time the call must be queued to the
present route before it can be routed to the
valuegroup/individualspeedcalling feature.
-If a speed calling short delay is given on
Record Code GS, columns 17-31, this field
determines the length of the delay.
-This feature provides a short delay between
the dialing of the number and the CO sending
dial tone (this is often required for...

TL-130400-1001COL.
NO.
Table 4.6Entry Fields for Record Code OV (Continued)
COL.VALID
NAMEENTRIESCOMMENTS26-27
Network Control5-15 = seconds
Center OutputIf the system scans the NCC (Network Control
-- = N/AScan TimeCenter) for any output, this field determines the
time between the scans.
-Interval .,x1-This field only applies to a system that is
used as an NCC.
28-29Integrating
00-20 = time inWhen the OMNI IVMS” message waiting
Voice
millisecondsfeature is accessed, this field determines how
Messaging
....

r
Record Code OD:4.7 Record Code 00, Figure 4.7, defines certain types of
Other Directory Numbersdirectory numbers that are not associated with a line circuit.
III
IIT T TTII
II 66 616II
1; 4 14 0 ;4I
I4II
I
I
11 15;I1
IIIIIIII
II r I
; F SN;R-G;IITIl 0 EoIE-O.,IIRI+R 0;c DIIlAtI ME II‘NI
IIIIisIIII
IIII
IIICi1 . .I
II 1011 IDII ‘ElI I I
I I I
I 
I III ;II I
I I I
I I I
I I I
Figure 4.7 Record Code OD:Other Directory Numbers Data Sheet 

TL-130400-1001Table 4.7
Entry Fields for Record Code OD
COL.NO.
19-22
COL.NAME
Directory
Number
Code Type
IdentifierVALID
ENTRIES
0000-9999 or
000-999 for
three-digit
numbers
MDU = messagedeskunattended
RMA = remoteaccess directory
number
SPD = call forward
to individual speed
call list entry
TGO = satellite
access-trunk
group outplusing
TGS = satelliteaccess-trunk
group select
VMS = IVMS(Integrated Voice
Messaging
System) directory
number
0000-0063 =
trunk group
number (MDU,
TGS, and VMS)
0000 =remote...

‘-----.----T---T-------r-____________-----------------------------------------I
II I I;5 II
I
II KI; .p..;0III -I
I2I
III 
--..1III x II-IIII
II’ I‘F SI! IT,
0 E
I1  IRIR QIM.II $1
II’ iSII III ICII
II 18;II lEl’ ’ III : i’ ’ I’ ’ I’ ’ I’ ’ I
Predeterminedhunt group or a station number required for P$A (Predetermined
Night AnswerNight Answer) service. A maximum number of 16 hunt
Pilot Numbersgroups or station numbers can be assigned for PNA service.
II’ i I1 ’ I
I I
T-T-T-T-T-Ip-:13131414141‘8 1...

TL-130400-1001Record Code PZ:
Paging Zones4.9 Record Code PZ, Figure 4.9, defines the paging zones for
the system. The attendant and certain system stations can be
allowed to access the paging equipment. A station user can
access the paging system by dialing an access code and zone
number. The attendant can access the paging system by the
above method or by depressing.the console PAGE button. The
card used to support this feature is the FB-17210 card and
paging is assigned to circuit 2.
: F’ 0
iRIMI
I
I...

TL-130400-1001Table 4.9Entry Fields for Record Code PZCOMMENTS
-The attendant paging area is normally an all
call for all zones.
-If this feature is allowed, Record Code CA,
This field determines whether or not the 0
zone digit must be dialed to access the zone.
-If the site only has one zone, a zonedigit is
-If thesitehasmore thanone zone, a digit
must be dialed to identify what zone is to be
paged. 

TL-130400-1001Record Code SL:
User Security4.10 Record Code SL, Figure 4.10, defines passwords to access
Level Passwordboth the voice and data software of the system. If the system isequipped with the PD-200 Data Option, this record code mustbe completed for the data security level. To date, eight security
levels for voice and six security levels for data have been
defined. The user can perform the functions associated with the
level accessed, including the functions associated with all lower
levels. Use...