GTE Omni Si Database Technical Practices Manual

Table 3.4Card Types Versus Identifiers Checks (Continue1
CARD TYPEPRIMARY IDENTIFIER
ADMP ADMP number
AIODN/A
ART
ART card number
BTPacket router number
CIPRelative controller card
number
CONF 
($$erFnce circuit
SECONDARY IDENTIFIER
AnlX$le~ard
N/AN/A
Local packet bus/ bus
segment
N/AN/A
DCP
DCPB
DVC
FPFPOP
OFFP
OPINIC
PBE
POTS
PRSM
VCIPVP20DCP number
DCP number
Relative line card
number
Relative line card
number
lariat& line card
Relative line card
number
N/A
Controlling DCP number
Packet router number...

-TL-130400-1001TL-130400-1001
NOTES:
Check 1.For card type ADMP. The
card number combinationFor card type ART. The 
P
duplicated. Check 2.
Check 3.
v-.I *
-.
- Check 4.
Check 5.
Check 6.Check 
7.
Check 8.
Check 9.
Check 10.
Check 11.For card types containing
packet 
bus/ bus segment i
DCPB), the packet router r
bus/bus segment identifieracross any of the card 
type
For card types containing r
information 
(CIP, DVC, VCI,relative controller card nurr
duplicated across any of th
For card type CONF, the cc...

. .
-TL-130400-1001
SYSTEM4.0 This section describes the record codes required to define
PARAMETERS ANDthe various system parameters and miscellaneous features. The
MISCELLANEOUSfollowing record codes are required:
FEATURES
l Record Code DT defines the location of the system’s DTMF
cards.
l Record Code OC defines the location of the conference, AIOD,
and Music-On-Hold circuit cards.
.l Record Code OE defines miscellaneous system data.
l Record Code OF defines additional miscellaneous system
data.
0...

TL-130400-I 001Record Code DT:4.1 Record Code DT, Figure 4.1, defines the location and
DTMF Receiverstatus of the system’s DTMF (FB-17203) receiver card(s).
The system can support a maximum of two DTMF receiver
cards with four circuits per card.
r---------r---r-r-------T---T-----------------------------------------------~II III
II
II III
III IIT T T TI T IIIIIII
II
II
-I x
Figure 4.1
Record Code DT: DTMF Receiver Data Sheet
Table 
4.1Entry Fields for Record Code DT
COL.NO.
12-13
15
16-17
18
19-20...

TL-130400-1001Record Code OC:4.2 Record Code OC, Figure 4.2, defines the location and status
Office Features Circuitsof the Music-On-Hold circuit cards.
r---------T-T-----,---7-I--;----------------‘-----------------------------~-~I ,
IIT,IIRIIA,IINIIISIIA,IIC,IT,
MUSIC ONII I IHOLD CKTI
IIO1IIN,II
IIICI
L--,-
l---IO1-.ID,IE,I I ’I l
I II ,
I ,
I 1
’ I
II ,...

TL-130400-1001Record Code OE:4.3 Record Code OE, Figure 4.3, defines miscellaneous office
Office Equipmentand equipment data.
PECI 
’I1 I1 I1 I1 I1 I1 I1 I1 I1 I1 1212121212121212121213131313131313131313l4l4l4I,7l819lO11 12131415161718191011 12131415161718191011 12131415161716191011 121~-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-~,,)lolg,ol I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I IL_L-L-L-L-~_~-*_*-~-~-~-~-~-~-~-~-~-~-*-~-~-~-~-*-~-~-*-~-~-~-~-~-~-~-~-~...

TL-130400-1001Table 4.3Entry Fields for Record Code QECOMMENTS
assigned to this system.
-This number is used for identification
rmoreoffice codesare usedbyaConsultationconsultation-The recommended value for this field is 3.
-If 1 is entered, a three-way conference
cannot be held by any line in the system.
21Transfer DivertP = divert toIf a call is transferred to a busy or no answer
Back Method on transferring partystation, this field determines whether the call
Busy or NoA = divert towill go back to the...

TL-130400-1004
Table 4.3
Entry Fields for Record Code OE (Continued)COMMENTS
This field only app
-This field determines whether or not a burst
of tone is heard by the station user if the call is
to go out over a route marked for burst tone.
-Normally the burst tone is put on the last
and most expensive trunk group in a route.
-This feature lets the station user decide
whether to hang up and try later on a cheaper
N = not providedermines w
requires a short cable application.
-If the site is located less...

-TL-130400-1001
COL.NO.
Table 4.3Entry Fields for Record Code OE (Continued)
COL.VALID
NAMEENTRIESCOMMENTS
50
-.Network Control
- = not equippedEnter Y If a CEC port is used for the NCC
Center PortY = equipped(Network Control Center).
Usage-The network control center provides network
x-administration control and maintenance.j *functions.
-MDR output for a network can be sent to an
NCC via an MDR port.
51-54 
-.Systems‘I 5210 = SVR for thisThe SVR for the system being installed is
System Version...

TL-130400-1001
Record Code OF:4.4 Record Code OF, Figure 4.4, provides information about
Office Featuresmiscellaneous system features.
~-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-1010121OlFl I I I I I I I f l I l I l I l I I 11 I I l l l l I l I I lL-L-L-~-i-*-~-~-~-~-~-~-~-~-~-~-~-~-~-~-*-~-~-~-~-*-~-~-~-~-~-~-~-~-~-~-
AlGl
EINITII41414141
41516171
.-l-L.-L-l
S: RI M; Ri S; Di Fi C Cl MjI EI Ei EI EI 11 RI H ol UIDI MI RI SI CI SI LI E DI TIGI 01 SI EI UI AI SI C El )I;TI VI...