GTE Omni Scbs Installation And Maintenance Manual

f”~‘ ‘.\‘\/‘!:  :‘\Laboratory Activity 
- Package C Data Base
Adminstration (5.3) (Continued)
GTE aww SEESPART 3: DIRECT INWARD DIALING
I.PRIOR TO PROGRAMMING, EMULATE A DID LINE BY PUNCHING THE TIP/RING WIRES FROM A SLT TO THE TIP/RING
WIRES OF A LOOP TIE TRUNK CIRCUIT (USE EQUIPMENT NUMBER 160).
2.USE THE CMC-250 TO ASSIGN A DID TRUNK USING THE FOLLOWING PARAMETER VALUES:
EQUIPMENT NUMBER (PI) = 160
TYPE OF TRUNK (P2) = 13 (LOOP DIAL)
TRUNK GROUP NUMBER (P3) = 57
OPERATION MODE (P4) = 1 (INCOMING)...

Laboratory Activity - Package C Data Base
Adminstration (5.3) (Continued)
GTE OMNU a3cs
PART 4:KEY SYSTEM FEATURES
1. REMOVE ATTENDANT CONSOLE.
2.COLD RESTART THE SYSTEM.
3.CHECK/CONFIRM KEY SYSTEM FEATURE CHANGES ON EKT INSTRUMENT BUTTONS.
5.98 

Review Exercise - Package C
Data Base 
Adminstration(5.3)INSTRUCTIONS: THE FOLLOWING EXERCISE CONSISTS OF MULTIPLE CHOICE, TRUE/FALSE, 
FILL IN THE
BLANK, OR MATCHING TYPE QUESTIONS. ALL AVAILABLE RESOURCES (I.E., STUDENT WORKBOOK, NOTES,
AND GTEP MANUAL) MAY BE USED AS REFERENCES. SUBMIT EXERCISE TO INSTRUCTOR FOR GRADING WHEN
LAST QUESTION HAS BEEN COMPLETED.
1.WHAT INSTALLATION OR DATA BASE PROGRAMMING STEPS ARE REQUIRED TO ALLOW A PREVIOUSLY
INSTALLED 
BLF/DSS MODULE TO FUNCTION AS A ROOM STATUS...

ew Exercise = Package CDntinued)
7.
8.
9.
10.CMC-430 ASSIGNS 
DISA DIRECTORY NUMBERS AND AN AUTHORIZATON CODE TO A
TRUNK LINE.
A CS-10 OR CS-20 WHICH WILL SERVE AS A VOICE STATION ASSOCIATED WITH A DIU MUST BE
ASSIGNED WITH 
CMC-, AND HAVE THEFEATURE BUTTON ASSIGNED
WITH CMC-203.
EKT INSTRUMENTS CONNECTED TO CARD SLOT
RING ON ALL INCOMING CALLS IN A KEY
TELEPHONE BUTTON ARRANGEMENT.
MATCH EACH OF THE FOLLOWING CMC COMMANDS WITH ITS CORRECT FUNCTION:
CMC-223
A. ASSIGNS TRUNK 
COSICOR TO DID TRUNKS...

PACKAGE C
MAINTENANCE
5.101 

5.4 EnablingObiective
GIVEN:0
0
0
0
0GTE 
OMNI SBCS
GTE 
OMNI SBCS PACKAGE C EQUIPMENT AND PERIPHERALS
ATTENDANT CONSOLE (ASSIGNED AS MASTER CONTROL TELEPHONE IN
DATA BASE)GTE 
OMNI SBCS COURSE AND SITE DOCUMENTATION PACKAGE
REVIEW EXERCISE
ACTION:
CRITERIA:
0
Q
6
0
USE ATTENDANT CONSOLE AS AN ALTERNATE MASTER CONTROL TELEPHONEFOR DATA BASE 
ADMINSTRATION AND MAINTENANCE TASKS.
IDENTIFY FUNCTIONSAND APPLICATIOtiS OF PACKAGE C CMC MAINTENANCE
COMMANDS.
MODIFY PARAMETER VALUES FOR PACKAGE C CMC...

Attendee Assignment as Master
e1 DESCRIPTION 1
.
A MAXIMUM OF TWO ATTENDANT CONSOLES CAN BE IDENTIFIED IN SYSTEM AS HAVING MASTER
CONTROL TELEPHONE (MCT) CAPABILITIES FOR DATA BASE ADMINSTRATION AND
MAINTENANCE ACTIVITIES..
ATTENDANT CONSOLE FIRST MUST BE PLACED IN THE POSITION BUSY MODE TO FUNCTION AS
AN MCT.
1.ASSIGN OR CANCEL ATTENDANT CONSOLE DIRECTORY NUMBER
AS MCT WITH CMC-702:.MCT NUMBER 
(Pl) - (1 - 4)
.
DIRECTORY NUMBER OF MCT ATTENDANT CONSOLE (P2)
(ATTENDANT CONSOLE ACCESS (0) + ATTENDANT...

Attehdent Console Operation as
Master Control 
ITelepPROCEDURE
1.
2.
3.
4.
5.PLACE ATTENDANT CONSOLE IN POSITION BUSY MODE BY DEPRESSING THE POSITION BUSY FEATURE BUTTON. ANY
CALLS IN PROCESS MUST BE CLEARED BEFORE POSITION BUSY MODE CAN BE ACTIVATED.
ENTER APPROPRIATE HIGH OR LOW LEVEL SECURITY CODE USING KEYBOARD OF ATTENDANT CONSOLE
(PREVIOUSLY ASSIGNED AS MCT) WHILE ON-HOOK AND IN IDLE STATE.
AT COMMAND PROMPT, ENTER APPROPRIATE CMC COMMAND AND PRESS SELECT (ATTENDANT CONSOLE’S
DEFAULT INCOMING...

Student Notes
5.105 

Attendent Console
Instrumentiagnostics
.ATTENDANT CONSOLE MUST BE TESTED OFF-LINE.0THE FOLLOWING TESTS CAN BE PERFORMED:
-BUTTON AND KEYPAD TEST
- LED LAMP TEST
- LCD DISPLAY TEST
- AUDIBLE TONE TEST
1.
2.
3.
4.
5.
6.UNPLUG TELEPHONE CORD FROM MODULAR JACK IN BACK OF ATTENDANT CONSOLE.
PRESS 1 and 3 KEYS SIMULTANEOUSLY.
PLUG TELEPHONE CORD INTO MODULAR JACK WHILE KEEPING THE 1 AND 3 KEYS PRESSED.
WHEN STEP 3 IS COMPLETED, PRESS ANY KEY TO ELIMINATE 
lNlTlALSIGNAL(INDICATING INSTRUMENT IS
IN DIAGNOSTIC...