GTE Omni Scbs Installation And Maintenance Manual

ttendant Console
iagnsstics (Continued)
ATTENDANT CONSOLE TEST BUTTON ARRANGEMENT
rl
rzl
rl
r”“4
rv VOL A
IIXEHZID 

Attendant Console Test Execution
KEY PREsSEDATTENDANT CONSOLE NUMERIC KEYPAD TESTFUNCTION
KEYPAD:
1
2
3
4
5
6
7
8
9
8
#*
STOP RINGING, DISPLAY SHOWS 1 ON THE LCD
START 
RlNGBNG IN PATTERN 1, DISPLAY SHOWS 2 ON THE LCD
START 
RINGING IN PATTERN 2, DISPLAY SHOWS 3 ON THE LCD
START RINGING IN PATTERN 3, DISPLAY SHOWS 4 ON THE LCD
INGBNG IN PATTEN 4, DISPLAY SHOWS 5
~~G~~G IN PATTEN 5, DISPLAY SHOWS 6
INGING IN PATTI5N 6, DISPLAY SHOWS
INGING IN PATTEN 7, DISPLAY SHOWS
lNGlNG BNPATTERN 8, DISPLAY SHOWS 9 ON...

Attendant Console Test Execution
(Continued)
ATTENDANT CONSOLE FUNCTION KEY TEST
FUNCTIONKEY:
FK16
FK17
FK18
FK19
FK20
FK2i
FK22
FK23
FK24
FK25
FK26
FK27
FK28
FK29
FK30
FK31DISPLAY SHOWS 
@ ON THE LCD
DISPLAY SHOWS A ON THE LCD
ASSOCIATED LAMP FLASHES IN PATTERN 4, DISPLAY SHOWS B ON THE LED
ASSOCIATED LAMP FLASHES IN PATTERN 4, DISPLAY SHOWS C ON THE LED
ASSOCIATED LAMP FLASHES IN PATTERN 4, DISPLAY SHOWS D ON THE LED
ASSOCIATED LAMP FLASHES IN PATTERN 4, DISPLAY SHOWS E ON THE LED
ASSOCIATED LAMP...

Attendant Console Test Execution
(Continued)
ATTENDANT CONSOLE FUNCTION KEY TEST
KEYPRESSED
FUNCTIONKEY:STA
RECALL
INCOMING
POS.RLSE
SUP/HOLD
SER/LOCK
SRCE
DEST
CONFIJOIN
DROPICNCL
VOL UP
VOL DOWN
SK1
SK2
SK3
SK4
SK5
SK6FUNCTION
ASSOCIATED LAMP FLASHES IN PATTERN 4, DISPLAY SHOWS P ON THE LED
ASSOCIATED LAMP FLASHES IN PATTERN 4, DISPLAY SHOWS 
Q ON THE LED
ASSOCIATED LAMP FLASHES IN PATTERN 4, DISPLAY SHOWS R ON THE LED
DISPLAY SHOWS S ON LCD
DISPLAY SHOWS T ON LCD
DISPLAY SHOWS U ON LCD
ASSOCIATED LAMP...

ATTENDANT CONSOLE TEST LAMP PATTERNSLAMP PATTERN
INDICATOR
PATTERN
0.125 SEC. ON, 0.125 SEC. OFF
0.5 SEC. ON, 0.5 SEC. OFF
0.125 SEC. OFF, 0.125 SEC. ON,0.125SEC.OFF, 0.125 SEC. ON,1.625SEC.OFF
0.125 SEC. OFF, 1.875 SEC. ON
STEADY ON
STEADY OFF
0.125 SEC. ON, 0.125 SEC. OFF,0.125SEC.ON, 0.125 SEC. OFF,1.625SEC.ON
1 SEC. ON, 1 SEC. OFF
5.111 

tf1 DESCRIPTION
0DATA INTERFACE UNIT (DIU) MUST BE TESTED OFF-LINE.
~bTHE FOLLOWING TESTS CAN BE PERFORMED:
- INITIAL CONDITION TEST
- CALL BUTTON TEST
- TEST SWITCH TEST
- DTEIDCEODE SWITCH TEST
3.4. PRESS A
TEST 
EXECUTI
FOLLOWONITOR 
VISULE RESULTS.
5.112 

ata Intet Test Execution
DATA INTERFACE UNIT TESTTEST 
ITEMINITIAL CONDITIONFUNCTION
RINGING START IN PATTERN 4
POW LAMP FLASHES IN PATTERN 1
TEST LAMP INDICATES ON
CALL LAMP FLASHES IN PATTERN 7
MI/MIC SIGNAL IS SET TO OFF
PRESS CALL BUTTON
CALL LAMP FLASHES, CHANGING IN PATTERNS FROM 0 TO 7RINGING STARTS, CHANGING IN PATTERNS FROM 0 TO 7
TEST SWITCH
TEST LAMP GOES ON WHEN SWITCH IS SETTO ON, TEST LAMP GOESOFF WHEN SWITCH IS SET TO OFF
DTE/DCE SWITCH MODE
IN DCE MODE, MI/MIC SIGNAL GOES OFF, AND POW...

Hotel/Motel Printer Busy AssignmentGE OMNU SBCS1 DESCRIPTION 1
*PLACES HOTEL/MOTEL PRINTER OUT OF SERVlCE (MADE BUSY) WHILE
MAINTENANCE PROCEDURES ARE BEING PERFORMED.
@SAME COMMAND IS USED TO RESTORE SERVICE TO HOTEL/MOTEL
PRINTER.
5.114
)1 PROCEDURE 1
1.USE CMC-706 TO MAKE HOTEL/MOTEL PRINTER BUSY OR RETURN IT
TO SERVICE:
0PRINTER NUMBER (PI) - (1 OR 2)
@MAKE BUSY OR PUT IN SERVICE FLAG (P2) - (0 = IN SERVICE;
I= MAKE BUSY). 

fi;:, ‘\,, ..,I\I’ ,,j?
aracter TT)Loop TestDESCRIPTION 
1.
PERFORMS LOOP TEST WlTHlN 4CHT CARD AND BETWEEN 4CHT CARD AND DIU/DTA..
TEST CHECKS FOR TRANSMISSIQN TIMING OUT, PARITY ERRORS, OVERRUN ERRORS, FRAMING
ERRORS, CHT STATUS DISAGREEMENT, TRANSMISSION AND RECEPTION CHARACTERS, AND
RECEPTION TIMING OUT.
PROCEDURE
1.USE CMC-810 TO ENTER PARAMETERS REQUIRED TO PERFORM LOOP TEST WITHIN 4CHT CARD:
0TEST TYPE (Pl) - (0 = LOOP TEST WITHIN 4 CHT;
1 = LOOP TEST BETWEEN 4CHT AND 
DIUIDTA).
CHARACTER TRUNK...

Character Trunk(CHT)LoopTest(
LOOP TEST RESULT MEANINGS
P4 VALUE
ANS2 (3 DIGITS)
FIRST DIGIT:O/l TO 9 = NORMAL/CHT STATUS DISAGREEMENT (NUMBER OF
OCCURRENCES)
SECOND DIGIT:
O/1 TO 9 = NORMAL/DISAGREEMENT OF TRANSMISSION AND
RECEPTION CHARACTERS (NUMBER OF OCCURRENCES)THIRD 
DIGIP‘..O/l TO 9 = NORMAL/RECEPTION TIMING OUT (NUMBER OF
OCCURRENCES)
P5 VALUEANSI (4 DIGITS)
FIRST DIGIT:O/l TO 9 = NORMAL/TRANSMISSION TIMING OUT (NUMBER OF
QCCURRENCES)
SECOND DIGIT:
O/l TO 9 = NORMAL/PARITY ERROR (NUMBER OF...