Getnet Router GR-534W User Manual

 
76 
 
 
On this page, you can modify the WPS settings. WPS can make your client 
automatically synchronize with the AP setting, and establish connection. 
  WPS Config 
 
  

 
77 
WPS: enable or disable WPS.   
After enabling WPS, you can configure the parameters related to WPS. 
  WPS Summary 
 
 
WPS summary displays the preset WPS information, such as WPS current status, 
WPS authentication mode, and WPS encryption type. 
Click the Reset OOB button on the Wi-Fi Protected Setup page, system displays 
the WPS default settings. See the following figure: 
 
 
  WPS Progress  

 
78 
 
 
WPS modes include PIN and PBC. For more details, please refer to WPS 
Applications. 
  WPS Status 
 
 
The figure above displays WPS current status. 
  WPS Applications 
This page provides two WPS modes, including PIN and PBC modes. 
At present, WPS supports three types of operation modes, including Enrollee mode, 
Registrar mode, and PBC mode. Enrollee and Registrar modes need to apply PIN 
negotiation.
 
- Enrollee Mode 
Step1 Select the enrollee mode on the wireless client, and the software...

 
79 
- Registrar Mode 
Step1 View the AP PIN on the Wi-Fi Protected Setup page, for example, 
31668729. 
 
 
Step2 Select Registrar mode on the wireless client and enter the PIN code of the 
GR-534W. See the following figure: 
 
- PBC Mode 
Step1 On the Wi-Fi Protected Setup page, select the PBC mode, and then click 
the Apply button. Or press the WPS button on the rear panel. 
 
  

 
80 
Step2 Enable the PBC function on the wireless client. In that case, GR-534W and 
wireless client will automatically establish connection. 
 
5.4.5   Station List 
Click Wireless > Station List to display the Station List page. 
 
 
On this page, you can view the wireless networks that connect to the GR-534W. 
If there is any wireless network connects to GR-534W, refresh this page and the 
connection information of the wireless network is displayed. See the following figure: 
 
 
5.4.6   Wireless...

 
81 
 
 
Step1 Click Wireless > Basic to display the Basic Wireless Settings page. 
 
Step2 On this page, set the AP channel to accord with the peer AP (An AP that 
wants to connect to the GR-534W by WDS). 
Step3 On the Basic Wireless Settings page, set the WDS mode to be Repeater 
Mode, set the physical mode and the encryption type of AP to accord with 
that of peer AP, and then enter the MAC address of the peer AP. After 
finishing the settings, click the Apply button to apply the settings. The...

 
82 
 
 
Step4 Click Wireless > Security to display the Wireless Security/Encryption 
Settings page. 
 
Step5 On this page, set the security mode of the GR-534W to accord with the peer 
AP. 
 
Note: 
In the WDS mode, do not set any mixed modes, for example, WPA-PSK/WPA2-PSK. 
  WDS Bridge Mode 
In the Bridge mode, you can use the GR-534W to connect to your router, for  

 
83 
extending wireless coverage. Meanwhile, it can also decrease the working load of the 
AP that accesses the Internet. In that case, the wireless card does not directly 
communicate with the wireless device that accesses the Internet, but it directly 
communicates with the GR-534W. 
 
 
Step1 On the Basic Wireless Settings page, select the WDS mode to be Bridge 
Mode.  

 
84 
 
 
Step2 On the Basic Wireless Settings page, set the physical mode and the 
encryption type of AP to accord with that of peer AP, and then enter the 
MAC address of the peer AP. After finishing the settings, click the Apply 
button to apply the settings. The GR-534W will work in the Bridge mode. 
Step3 On this page, set the security mode of the GR-534W to accord with the 
peer AP. 
 
  

 
85 
Note: 
In the WDS mode, do not set any mixed modes, for example, WPA-PSK/WPA2-PSK. 
 
  WDS Lazy Mode   
In the Lazy mode, the GR-534W automatically connects to the WDS devices that use 
the same SSID, channel, encryption mode, and physical mode. You do not need to 
manually enter other MAC addresses of peer APs. 
 
 
Step1 On the Basic Wireless Settings page, set the WDS mode to be Lazy 
Mode, set the physical mode and the encryption type of AP to accord with 
that of peer AP, and then enter the...