Home > Getnet > Router > Getnet Router GR-534W User Manual

Getnet Router GR-534W User Manual

Here you can view all the pages of manual Getnet Router GR-534W User Manual. The Getnet manuals for Router are available online for free. You can easily download all the documents as PDF.

Page 111

 
106 
Field Description 
AC_VI, and AC_VO. 
Direct Link Setup  Enable or disable direct link setup. 
 
  Direct Link Setup (DLS) 
After enabling direct link setup, you are allowed to set the MAC address and the 
timeout value. 
 
 
The parameters of Direct Link Setup are described as follows: 
Field Description 
MAC Address  Enter  the  MAC  address of the DLS client. 
Timeout Value  Enter the timeout value for stopping DLS. 
 
  DLS Status 
 
 
The figure above displays the DLS clients’ status. 
5.5.7...

Page 112

 
107 
 
 
This page is used to configure the parameters of 802.11n in the station mode. 
The parameters of this page are described as follows:
 
Field Description 
MPDU Aggregation  Enable or disable MPDU (Message Protocol Data 
Unit) aggregation. A-MPDU aggregates the 
MPDUs that are encapsulated by 802.11 
message. MPDU is data frame that is 
encapsulated by 802.11. By sending A-MPDU, it 
decreases PLCP Preamble and PLCP Header 
that are needed to send an 802.11 message, and 
the system throughput is...

Page 113

 
108 
Field Description 
802.11 one by one. 
A-MSDU aggregates multiple A-MSDU 
Subframes and encapsulates them to be an 
802.11 message. In this way, PLCP Preamble, 
PLCP Header, and 802.11 MAC overhead that are 
needed for sending an 802.11 message decrease. 
At the same time, the acknowledge frames also 
decrease, and the efficiency for sending message 
is improved. 
5.5.8  WPS 
Click Wireless > WPS to display the Wi-Fi Protected Setup (STA) page. 
 
 
On this page, you are allowed to configure WPS...

Page 114

 
109 
 
 
If the nearby APs are scanned, the WPS AP Site Survey list will display the 
information about the scanned APs, such as SSID, BSSID, and encryption status. 
  WPS Buttons and Modes 
 
 
The buttons and WPS modes are described as follows: 
Button/Field Description 
Refresh  Click this button, and then the WPS AP Site 
Survey list will be refreshed. 
Mode It provides Enrollee mode and Registrar mode. 
   Enrollee mode: if selecting this mode, you 
need to enter Station PIN on AP for WPS...

Page 115

 
110 
 
 
The figure above shows the WPS status. 
  Registrar Settings 
When selecting Registrar mode, system displays the Registrar Settings table. 
Registrar Settings table provides OPEN, WPA-PSK, and WAP2-PSK authentication 
modes. 
- OPEN 
When selecting the OPEN authentication mode, the system displays the following 
page: 
 
 
The parameters of OPEN authentication mode are described as follows: 
Field Description 
SSID  Set the network name. 
Authentication Select OPEN mode in the drop down list....

Page 116

 
111 
Field Description 
WEP Key Type  The key type is Hex or ASCII. 
   Hex: the key length can be 10 bits or 26 bits.
   ASCII: the key length can be 5 bits or 13 bits.
WEP Key Index  Select the WEP key in the drop down list. 
Key  Set the key according to the key type and the key 
length. 
 
- WPA-PSK and WAP2-PSK 
When selecting the WPA-PSK or WPA2-PSK authentication mode, the system 
displays the following page: 
 
 
The parameters of WPA-PSK or WPA2-PSK authentication mode are described as...

Page 117

 
112 
Preparation: 
Prepare two GR-534W s, and set their operation modes. 
(1)   One is set to be WISP mode, that is, wireless station mode .This device is called 
STA hereinafter. The Pin code is 31669603. 
(2)   The other is set to be Gateway mode or Bridge mode, that is, wireless AP mode. 
This device is called AP hereinafter. The PIN code is 31668569. 
(3)  Enter the Station Site Survey page of STA to view the APs in the Site Survey 
list. Please make sure that the Sample_AP is in the list and its...

Page 118

 
113 
 
 
Step2 Enter the Wi-Fi Protected Setup (STA) page of STA. On this page, click 
the PBC Start button to make STA start WPS negotiation.  

Page 119

 
114 
 
 
Step3 Please pay attention to the WPS status of STA. After finishing negotiating, 
system displays the following page. 
 
 
- Enrollee Mode  

Page 120

 
115 
Step1 Enter the PIN code of STA (31669603) on the Wi-Fi Protected Setup 
page of AP, and then click the Apply button. 
 
 
Step2 Meanwhile, click the PIN Start button on the Wi-Fi Protected Setup (STA) 
page of STA to make STA start negotiation. After finishing negotiation, 
system displays the following page.  
Start reading Getnet Router GR-534W User Manual

Related Manuals for Getnet Router GR-534W User Manual

All Getnet manuals