GE Nx 8 Manual
Have a look at the manual GE Nx 8 Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 45 GE manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
GE Security g
Segment 1 Partition 1 “Sensor Low battery Code”
Segment 2 Partition 2 “Sensor Low battery Code”
Segment 3 Partition 3 “Sensor Low battery Code”
Segment 4 Partition 4 “Sensor Low battery Code”
Segment 5 Partition 5 “Sensor Low battery Code”
Segment 6 Partition 6 “Sensor Low battery Code”
Segment 7 Partition 7 “Sensor Low battery Code”
Segment 8 Partition 8 “Sensor Low battery Code”
LOCATION 61 - SENSOR MISSING COMMUNICATOR CODE, SLOW SPEED FORMATS ONLY (8
segments, numerical data)
Location 61 contains the event code for a zone “Sensor-missing” for a 4+2 and 3+1
format. For a 4+2 format, the digit programmed in this location will be sent as the tens
digit of the sensor missing event code. The zone ID will always be reported as the ones
digit of the zone number (e.g. zone 16 = 6, zone 45 = 5).
This location contains 8 segments. Any segment left as “0” will follow the Segment 1
selection.
Segment 1 Partition 1 “Sensor Missing Code”
Segment 2 Partition 2 “Sensor Missing Code”
Segment 3 Partition 3 “Sensor Missing Code”
Segment 4 Partition 4 “Sensor Missing Code”
Segment 5 Partition 5 “Sensor Missing Code”
Segment 6 Partition 6 “Sensor Missing Code”
Segment 7 Partition 7 “Sensor Missing Code”
Segment 8 Partition 8 “Sensor Missing Code”
LOCATION 62 - DURESS COMMUNICATOR CODE, SLOW SPEED FORMATS ONLY (2 segments,
numerical data)
Location 62 contains the tens and ones digits that will be sent for a 4+2 and 3+1 format if
the duress code is enabled in location 44. Segment 1 contains the tens digit, and
segment 2 contains the ones digit.
For a 3+1 format, only the segment 1 digit (tens) will be sent.
LOCATION 63 - KEYPAD AUXILIARY 1 COMMUNICATOR CODE, SLOW SPEED FORMATS ONLY (2
segments, numerical data)
Location 63 contains the tens and ones digits that will be sent for a 4+2 and 3+1 format if
the keypad “Auxiliary 1” (FIRE) is enabled in the partition feature selection. Segment 1
contains the tens digit; segment 2 contains the ones digit.
For a 3+1 format, only the segment 1 digit (tens) will be sent.
NX-8E Installation manual Page 61 Date 08/09/04
GE Security g
LOCATION 64 - KEYPAD AUXILIARY 2 COMMUNICATOR CODE, SLOW SPEED FORMATS ONLY (2
segments, numerical data)
Location 64 contains the tens and ones digits that will be sent for a 4+2 and 3+1 format if
the keypad “Auxiliary 2” (MEDICAL) is enabled in the partition feature selection. Segment
1 contains the tens digit; segment 2 contains the ones digit.
For a 3+1 format, only the segment 1 digit (tens) will be sent.
LOCATION 65 - KEYPAD PANIC COMMUNICATOR CODE, SLOW SPEED FORMATS ONLY (2
segments, numerical data)
Location 65 contains the tens and ones digits that will be sent for a 4+2 and 3+1 format if
the keypad “Panic” is enabled in the partition feature selection. Segment 1 contains the
tens digit, and segment 2 contains the ones digit.
For a 3+1 format, only the segment 1 digit (tens) will be sent.
LOCATION 66 - KEYPAD MULTIPLE CODE ENTRY TAMPER COMMUNICATOR CODE, SLOW SPEED
FORMATS ONLY (2 segments, numerical data)
Location 66 contains the tens and ones digits that will be sent for a 4+2 and 3+1 format if
the keypad “Multiple Code Entry” (Tamper) is enabled in the partition feature selection.
Segment 1 contains the tens digit, and segment 2 contains the ones digit.
For a 3+1 format, only the segment 1 digit (tens) will be sent.
LOCATION 67 - BOX TAMPER / BOX TAMPER RESTORE COMMUNICATOR CODE, SLOW SPEED
FORMATS ONLY (4 segments, numerical data)
Location 67 contains the tens and ones digits that will be sent for a 4+2 and 3+1 format if
the “Box Tamper” feature is enabled in location 37. Segment 1 contains the tens digit of
the “Box Tamper”. Segment 2 contains the ones digit of the “Box Tamper”. Segment 3
contains the tens digit of the “Box Tamper Restore”. Segment 4 contains the ones digit of
the “Box Tamper Restore”.
For a 3+1 format, only the segment 1 resp. segment 3 digit (tens) will be sent.
LOCATION 68 - AC FAIL / AC FAIL RESTORE COMMUNICATOR CODES, SLOW SPEED FORMATS
ONLY (4 segments, numerical data)
Location 68 contains the tens and ones digits for a 4+2 and 3+1 format that will be sent if
“AC Fail Reporting” is enabled. Segment 1 contains the tens digit of the “AC Fail
Reporting”. Segment 2 contains the ones digit of the “AC Fail Reporting”. Segment 3
contains the tens digit of the “AC Fail Restore”. Segment 4 contains the ones digit of the
“AC Fail Restore”.
For a 3+1 format, only the segment 1 resp. segment 3 digit (tens) will be sent.
NX-8E Installation manual Page 62 Date 08/09/04
GE Security g
LOCATION 69 - LOW BATTERY / LOW BATTERY RESTORE COMMUNICATOR CODES, SLOW SPEED
FORMATS ONLY (4 segments, numerical data)
Location 69 contains the tens and ones digits for a 4+2 and 3+1 format that will be sent if
“Low Battery Reporting” is enabled. Segment 1 contains the tens digit of the “Low Battery
Reporting”. Segment 2 contains the ones digit of the “Low Battery Reporting”. Segment 3
contains the tens digit of the “Low Battery Restore”. Segment 4 contains the ones digit of
the “Low Battery Restore”.
For a 3+1 format, only the segment 1 digit resp. segment 3 digit (tens) will be sent.
LOCATION 70 - AUX POWER OVERCURRENT/ AUX POWER OVERCURRENT RESTORE
COMMUNICATOR CODES, SLOW SPEED FORMATS ONLY (4 segments, numerical data)
Location 70 contains the tens and ones digits for a 4+2 and 3+1 format that will be sent if
“Aux Power Overcurrent Reporting” is enabled. Segment 1 contains the tens digit of the
“Aux Power Overcurrent Reporting”. Segment 2 contains the ones digit of the “Aux Power
Overcurrent Reporting”. Segment 3 contains the tens digit of the “Aux Power Overcurrent
Restore”. Segment 4 contains the ones digit of the “Aux Power Overcurrent Restore”.
For a 3+1 format, only the segment 1 resp. segment 3 digit (tens) will be sent.
LOCATION 71 - BELL TAMPER AND BELL TAMPER RESTORE COMMUNICATOR CODES, SLOW
SPEED FORMATS ONLY (4 segments, numerical data)
Location 71 contains the tens and ones digits for a 4+2 and 3+1 format that will be sent if
siren supervision reporting is enabled. Segment 1 contains the tens digit of the “Bell
Tamper Reporting”. Segment 2 contains the ones digit of the “Bell Tamper Reporting”.
Segment 3 contains the tens digit of the “Bell Tamper Restore”. Segment 4 contains the
ones digit of the “Bell Tamper Restore”.
For a 3+1 format, only the segment 1 resp. segment 3 digit (tens) will be sent.
LOCATION 72 - TELEPHONE LINE CUT RESTORE COMMUNICATOR CODES, SLOW SPEED
FORMATS ONLY (4 segments, numerical data)
Location 72 contains the tens and ones digits for a 4+2 and 3+1 format that will be sent if
“Telephone Line Cut Restore Reporting” is enabled. Segment 1 and segment 2 are
reserved. Segment 3 contains the tens digit of the “Telephone Line Cut Restore”.
Segment 4 contains the ones digit of the “Telephone Line Cut Restore”.
For a 3+1 format, only the segment 3 digit (tens) will be sent.
LOCATION 73 - B-ALARM REPORT CODE (only for Norway/Sweden)
B-Alarm time is fixed at 30 minutes. The reporting of a B-Alarm is enabled if feature 7 is
set on location 37, segment 3.
NX-8E Installation manual Page 63 Date 08/09/04
GE Security g
LOCATION 74 - EXPANDER TROUBLE AND EXPANDER TROUBLE RESTORE COMMUNICATOR
CODES, SLOW SPEED FORMATS ONLY (4 segments, numerical data)
Location 74 contains the tens and ones digits for a 4+2 and 3+1 format that will be sent if
“Expander Trouble Reporting” is enabled. Segment 1 contains the tens digit of the
“Expander Trouble Reporting”. Segment 2 contains the ones digit of the “Expander
Trouble Reporting”. Segment 3 contains the tens digit of the “Expander Trouble Restore”.
Segment 4 contains the ones digit of the “Expander Trouble Restore”.
For a 3+1 format, only the segment 1 digit resp. segment 3 digit (tens) will be sent.
LOCATION 75 - FAIL TO COMMUNICATE COMMUNICATOR CODE, SLOW SPEED FORMATS ONLY (2
segments, numerical data)
Location 75 contains the tens and ones digits for a 4+2 and 3+1 format that will be sent if
the “Fail To Communicate Reporting” is enabled. Segment 1 contains the tens digit, and
segment 2 contains the ones digit.
For a 3+1 format, only the segment 1 digit (tens) will be sent.
LOCATION 76 - LOG FULL COMMUNICATOR CODE, SLOW SPEED FORMATS ONLY (2 segments,
numerical data)
Location 76 contains the tens and ones digits for a 4+2 and 3+1 format if the “Log Full
Reporting” is enabled. Segment 1 contains the tens digit, and segment 2 contains the
ones digit.
For a 3+1 format, only the segment 1 digit (tens) will be sent.
LOCATION 77 - OPENING COMMUNICATOR CODE, SLOW SPEED FORMATS ONLY (8 segments,
numerical data)
Location 77 contains the tens digit for a 4+2 and 3+1 format if “Opening Reporting” is
enabled. The ones digit is the ones digit of the user number that did the opening. If the
user is greater than 9, the numbers will begin repeating (e.g. code 6 = 6, code 45 = 5).
This location contains 8 segments. Any segment left as “0” will follow the segment 1
selection.
If you need to report openings and closings with a unique code per user, Contact ID or
SIA format must be used.
Segment 1 Opening code for partition 1
Segment 2 Opening code for partition 2
Segment 3 Opening code for partition 3
Segment 4 Opening code for partition 4
Segment 5 Opening code for partition 5
Segment 6 Opening code for partition 6
Segment 7 Opening code for partition 7
Segment 8 Opening code for partition 8
NX-8E Installation manual Page 64 Date 08/09/04
GE Security g
LOCATION 78 - CLOSING COMMUNICATOR CODE, SLOW SPEED FORMATS ONLY (8 segments,
numerical data)
Location 78 contains the tens digit for a 4+2 and 3+1 format if “Closing Reporting” is
enabled. The ones digit is the ones digit of the user number that did the opening. If the
user is greater than 9, the numbers will begin repeating (e.g. code 6 = 6, code 45 = 5).
This location contains 8 segments. Any segment left as “0” will follow the segment 1
selection.
If you need to report openings and closings with a unique code per user, Contact ID or
SIA format must be used.
Segment 1 Closing code for partition 1
Segment 2 Closing code for partition 2
Segment 3 Closing code for partition 3
Segment 4 Closing code for partition 4
Segment 5 Closing code for partition 5
Segment 6 Closing code for partition 6
Segment 7 Closing code for partition 7
Segment 8 Closing code for partition 8
LOCATION 79 - AUTOTEST COMMUNICATOR CODE, SLOW SPEED FORMATS ONLY (2 segments,
numerical data)
Location 79 contains the tens and ones digits for a 4+2 and 3+1 format that will be sent if
“Autotest” or “Manual Test” is enabled. Segment 1 contains the tens digit, and segment 2
contains the ones digit.
For a 3+1 format, only the segment 1 digit (tens) will be sent.
LOCATION 80 - RECENT CLOSING AND EXIT ERROR COMMUNICATOR CODE, SLOW SPEED
FORMATS ONLY (2 segments, numerical data)
Location 80 contains the tens digit for a 4+2 and 3+1 format that will be sent if “Recent
Closing” and/or “Exit Error Reporting” is enabled. Segment 1 contains the tens digit for
the “Recent Closing Reporting”. Segment 2 contains the tens digit for the “Exit Error
Reporting”. The ones digit is the ones digit of the user number that did the opening. If the
user is greater than 9, the numbers will begin repeating (e.g. code 6 = 6, code 45 = 5).
If you need to report Recent Closings and Exit Errors with a unique code per user,
Contact ID or SIA format must be used.
LOCATION 81 - START PROGRAM AND END PROGRAM COMMUNICATOR CODES, SLOW SPEED
FORMATS ONLY (4 segments, numerical data)
Location 81 contains the tens and ones digits for a 4+2 and 3+1 format that will be sent if
“Start / End Programming Reporting” is enabled. Segment 1 contains the tens digit of the
“Start Program Reporting”. Segment 2 contains the ones digit of the “Start Program
Reporting”. Segment 3 contains the tens digit of the “End Program Reporting”. Segment 4
contains the ones digit of the “End Program Reporting”.
For a 3+1 format, only the segment 1 digit resp. segment 3 digit (tens) will be sent.
NX-8E Installation manual Page 65 Date 08/09/04
GE Security g
LOCATION 82 - END DOWNLOAD COMMUNICATOR CODE, SLOW SPEED FORMATS ONLY (4
segments, numerical data)
Location 82 contains the tens and ones digits for a 4+2 and 3+1 format that will be sent if
“End Downloading Reporting” is enabled. Segment 1 and 2 are reserved. Segment 3
contains the tens digit of the “End Download Reporting”. Segment 4 contains the ones
digit of the “End Download Reporting”.
Note: A start download report will be sent to the internal event log.
For a 3+1 format, only the segment 1 digit (tens) will be sent.
LOCATION 83 - CANCEL COMMUNICATOR CODE, SLOW SPEED FORMATS ONLY (1 segments,
numerical data)
Location 83 contains the tens digit for a 4+2 and 3+1format that will be sent if “Cancel
Reporting” is enabled. Segment 1 contains the tens digit for the “Cancel Communicator
Reporting”. The ones digit is the ones digit of the user number that did the opening. If the
user is greater than 9, the numbers will begin repeating (e.g. code 6 = 6, code 45 = 5).
If you need to report Cancels with a unique code per user, Contact ID or SIA format must
be used.
LOCATIONS 84-87 - RESERVED
NX-8E Installation manual Page 66 Date 08/09/04
GE Security g
Programming partition parameters
LOCATIONS 88-109 ARE FOR PROGRAMMING DIFFERENT ACCOUNT CODES
AND/OR FEATURES FOR EACH PARTITION. IF A LOCATION IS LEFT
UNPROGRAMMED, THE FEATURE FOR PARTITION 1 AND THE ACCOUNT CODE
FOR THE PHONE NUMBER WILL BE USED
LOCATION 88 - ACCOUNT CODE FOR PARTITION 1 (6 segments, numerical data)
Location 88 contains the account code that is sent when partition 1 is reported. If location
88 is left unprogrammed (all “10”s), then the account code corresponding to the phone
number that is dialled will be used. If the account code is less than six digits, program a
“10” in the segment immediately after the last digit of the account code. If the account
code is 6 digits long, program all 6 segments.
LOCATION 89 - ACCOUNT CODE FOR PARTITION 2 (6 segments, numerical data)
Location 89 contains the account code that is sent when partition 2 is reported. If location
89 is left unprogrammed (all “10”s), then the account code corresponding to the phone
number that is dialled will be used. If the account code is less than six digits, program a
“10” in the segment immediately after the last digit of the account code. If the account
code is 6 digits long, program all 6 segments.
LOCATION 90 - PARTITION 2 FEATURE AND REPORTING SELECTIONS (5 segments, feature
selection data)
Location 90 is used to enable certain features that the user can access or see from the
keypad of the system. In addition, certain communicator reports are enabled in this
location. Each of these features can be enabled by partition. This location contains 5
segments, with eight possible features per segment. Refer to location 23 for the feature
selections. If all the segments are blank (nothing enabled), the features for partition 1 will
be used.
LOCATION 91 - PARTITION 2 ENTRY EXIT TIMERS (6 segments, numerical data)
Location 91 is used to enter the entry and exit times, in seconds. There are 2 separate
entry and exit times. Valid entries are 10-255 seconds. If all the segments are “0”, the
entry and exit times for partition 1 will be used.
Segment 1 Entry time 1 Entry time that will be used when a delay 1 zone
type initiates an entry delay
Segment 2 Entry time 2 Exit time that will be used for all zones designated
as delay 1
Segment 3 Entry time 3 Entry time that will be used when a delay 2 zone
type initiates an entry delay
Segment 4 Entry time 4 Exit time that will be used for all zones designated
as delay 2
Segment 5 Reserved
Segment 6 Reserved
NX-8E Installation manual Page 67 Date 08/09/04
GE Security g
LOCATION 92 - ACCOUNT CODE FOR PARTITION 3 (6 segments, numerical data)
The account code that is sent when reporting partition 3 is programmed in location 92. If
location 92 is left unprogrammed (all “10”), then the account code corresponding to the
phone number that is dialled will be used. If the account code is less than six digits,
program a “10” in the segment immediately after the last digit of the account code. If the
account code is 6 digits long, program all 6 segments.
LOCATION 93 - PARTITION 3 FEATURE AND REPORTING SELECTIONS (5 segments, feature
selection data)
Location 93 is used to enable certain features that the user can access or see from the
keypad of the system. In addition, certain communicator reports are enabled in this
location. Each of these features can be enabled by partition. This location contains 5
segments, with eight possible features per segment. Refer to location 23 for the feature
selections. If all the segments are blank (nothing enabled), the features for partition 1 will
be used.
LOCATION 94 - PARTITION 3 ENTRY EXIT TIMERS (6 segments, numerical data)
Location 94 is used to enter the entry and exit times, in seconds. There are 2 separate
entry and exit times. Valid entries are 10-255 seconds. If all the segments are “0”, the
entry and exit times for partition 1 will be used.
Segment 1 Entry time 1 Entry time that will be used when a delay 1 zone
type initiates an entry delay
Segment 2 Entry time 2 Exit time that will be used for all zones designated
as delay 1
Segment 3 Entry time 3 Entry time that will be used when a delay 2 zone
type initiates an entry delay
Segment 4 Entry time 4 Exit time that will be used for all zones designated
as delay 2
Segment 5 Reserved
Segment 6 Reserved
LOCATION 95 - ACCOUNT CODE FOR PARTITION 4 (6 segments, numerical data)
The account code that is sent when reporting partition 4 is programmed in location 95. If
location 95 is left unprogrammed (all “10”) then the account code corresponding to the
phone number that is dialled will be used. If the account code is less than six digits,
program a “10” in the segment immediately after the last digit of the account code. If the
account code is 6 digits long, program all 6 segments.
LOCATION 96 - PARTITION 4 FEATURE AND REPORTING SELECTIONS (5 segments, feature
selection data)
Location 96 is used to enable certain features that the user can access or see from the
keypad of the system. In addition, certain communicator reports are enabled in this
location. Each of these features can be enabled by partition. This location contains 5
segments, with eight possible features per segment. Refer to location 23 for the feature
selections. If all the segments are blank (nothing enabled), the features for partition 1 will
be used.
NX-8E Installation manual Page 68 Date 08/09/04
GE Security g
LOCATION 97 - PARTITION 4 ENTRY EXIT TIMERS (6 segments, numerical data)
Location 97 is used to enter the entry and exit times in seconds. There are 2 separate
entry and exit times. Valid entries are 10-255 seconds. If all the segments are “0”, the
entry and exit times for partition 1 will be used.
Segment 1 Entry time 1 Entry time that will be used when a delay 1 zone
type initiates an entry delay
Segment 2 Entry time 2 Exit time that will be used for all zones designated
as delay 1
Segment 3 Entry time 3 Entry time that will be used when a delay 2 zone
type initiates an entry delay
Segment 4 Entry time 4 Exit time that will be used for all zones designated
as delay 2
Segment 5 Reserved
Segment 6 Reserved
LOCATION 98 - ACCOUNT CODE FOR PARTITION 5 (6 segments, numerical data)
The account code that is sent when reporting partition 5 is programmed in location 98. If
location 98 is left unprogrammed (all “10”) then the account code corresponding to the
phone number that is dialled will be used. If the account code is less than six digits,
program a “10” in the segment immediately after the last digit of the account code. If the
account code is 6 digits long, program all 6 segments.
LOCATION 99 - PARTITION 5 FEATURE AND REPORTING SELECTIONS (5 segments, numerical data)
Location 99 is used to enable certain features that the user can access or see from the
keypad of the system. In addition, certain communicator reports are enabled in this
location. Each of these features can be enabled by partition. This location contains 5
segments, with eight possible features per segment. Refer to location 23 for the feature
selections. If all the segments are blank (nothing enabled), the features for partition 1 will
be used.
LOCATION 100 - PARTITION 5 ENTRY EXIT TIMERS (6 segments, numerical data)
Location 100 is used to enter the entry and exit times in seconds. There are 2 separate
entry and exit times. Valid entries are 10-255 seconds. If all the segments are “0”, the
entry and exit times for partition 1 will be used.
Segment 1 Entry time 1 Entry time that will be used when a delay 1 zone
type initiates an entry delay
Segment 2 Entry time 2 Exit time that will be used for all zones designated
as delay 1
Segment 3 Entry time 3 Entry time that will be used when a delay 2 zone
type initiates an entry delay
Segment 4 Entry time 4 Exit time that will be used for all zones designated
as delay 2
Segment 5 Reserved
Segment 6 Reserved
NX-8E Installation manual Page 69 Date 08/09/04
GE Security g
LOCATION 101 - ACCOUNT CODE FOR PARTITION 6 (6 segments, numerical data)
The account code that is sent when reporting partition 6 is programmed in location 101. If
location 101 is left unprogrammed (all “10”) then the account code corresponding to the
phone number that is dialled will be used. If the account code is less than six digits,
program a “10” in the segment immediately after the last digit of the account code. If the
account code is 6 digits long, program all 6 segments.
LOCATION 102 - PARTITION 6 FEATURE AND REPORTING SELECTIONS (5 segments, feature
selection data)
Location 102 is used to enable certain features that the user can access or see from the
keypad of the system. In addition, certain communicator reports are enabled in this
location. Each of these features can be enabled by partition. This location contains 5
segments, with eight possible features per segment. Refer to location 23 for the feature
selections. If all the segments are blank (nothing enabled), the features for partition 1 will
be used.
LOCATION 103 - PARTITION 6 ENTRY EXIT TIMERS (6 segments, numerical data)
Location 103 is used to enter the entry and exit times in seconds. There are 2 separate
entry and exit times. Valid entries are 10-255 seconds. If all the segments are “0”, the
entry and exit times for partition 1 will be used.
Segment 1 Entry time 1 Entry time that will be used when a delay 1 zone
type initiates an entry delay
Segment 2 Entry time 2 Exit time that will be used for all zones designated
as delay 1
Segment 3 Entry time 3 Entry time that will be used when a delay 2 zone
type initiates an entry delay
Segment 4 Entry time 4 Exit time that will be used for all zones designated
as delay 2
Segment 5 Reserved
Segment 6 Reserved
LOCATION 104 - ACCOUNT CODE FOR PARTITION 7 (6 segments, numerical data)
The account code that is sent when reporting partition 7 is programmed in location 104. If
location 104 is left unprogrammed (all “10”) then the account code corresponding to the
phone number that is dialled will be used. If the account code is less than six digits,
program a “10” in the segment immediately after the last digit of the account code. If the
account code is 6 digits long, program all 6 segments.
LOCATION 105 - PARTITION 7 FEATURE AND REPORTING SELECTIONS (5 segments, feature
selection data)
Location 105 is used to enable certain features that the user can access or see from the
keypad of the system. In addition, certain communicator reports are enabled in this
location. Each of these features can be enabled by partition. This location contains 5
segments, with eight possible features per segment. Refer to location 23 for the feature
selections. If all the segments are blank (nothing enabled), the features for partition 1 will
be used.
NX-8E Installation manual Page 70 Date 08/09/04