GE Logiq P5 User Manual

Console Overview
LOGIQ 5 Basic User Manual 3-11
Direction 2300002-100 Rev. 2
Peripheral/Accessory Connector Panel (continued)
 Figure 3-5. Peirpheral/Accessory Connector Panel
220-240V  500VA MaxIncluding front printer panel220-240V  500VA MaxIncluding rear panel
100~120V  500VA MaxIncluding front printer panel100~120V  500VA MaxIncluding rear panel
Japan/USA/Asia Console (100~120V
Europe/USA Console (220V)
CAUTIONThe connection of equipment or transmission networks other 
than as specified in these...

Preparing the System for Use
3-12 LOGIQ 5 Basic User Manual
Direction 2300002-100 Rev. 2
Peripheral/Accessory Connector Panel (continued)
Table 3-2: Peripheral/Accessory Connector Panel Descriptions
No.ItemType of connector Required Cable
1. S-Video Out S-Terminal, 4-pin
2. Composite Color/
BW
3. Audio In/Out RCA
4. S-Video In
5. Camera Color/
Camera B/W
6. VGA Shrinked D-Sub, 15-pin
7. Service USB(A)
8. VCR 1 USB(A)
9. VCR 2 USB(A)
10. For Future use
11 .  Insite RJ-11 Modular, 6-pin
12. Ethernet RJ-45...

Console Overview
LOGIQ 5 Basic User Manual 3-13
Direction 2300002-100 Rev. 2
Footswitch (Option)
Use only the recommended optional multifunctional footswitch.
 Figure 3-6. Footswitch
The footswitch may be used as select keys, video recording, etc. 
The three switches have different function assignments 
depending on the current application.
The footswitch connection is located below the operator control 
panel.
CAUTIONDO NOT place or store the footswitch in the side pocket or the 
Peripheral Device...

Preparing the System for Use
3-14 LOGIQ 5 Basic User Manual
Direction 2300002-100 Rev. 2
System Positioning/Transporting
Moving the System
When moving or transporting the system, follow the precautions 
below to ensure the maximum safety for personnel, the system, 
and other equipment. 
Before moving the system
1.  Press the Power on/Standby switch and turn off the circuit 
breaker to power off. See ‘Power Off’ for more information.
2.  Unplug the power cord.
3.  All cables from off-board peripheral...

System Positioning/Transporting
LOGIQ 5 Basic User Manual 3-15
Direction 2300002-100 Rev. 2
Before moving the system (continued)
To prevent damage to the Power Cord, DO NOT pull 
excessively on the cord or make sharp bends while 
wrapping.
 Figure 3-7. Location of rear handle
a. Handle
7.  Connect all probes to be used while off site. Ensure that 
probe cables are out of the way from the wheels and not 
protruding beyond the console.
NOTE:  If more than three (3) probes are intended to be used, store...

Preparing the System for Use
3-16 LOGIQ 5 Basic User Manual
Direction 2300002-100 Rev. 2
When moving the system
1.  Always use the rear handle grips to move the system.
2.  Take extra care when moving the system long distances and 
on inclines. Ask for help if necessary.
Avoid ramps that are steeper than ten degrees to avoid 
tipping over the
 system. 
NOTE:  Wheel chair ramps are usually less than five degrees. 
Utilize additional care and personnel when moving on steep 
incline (>5°) or loading into a...

System Positioning/Transporting
LOGIQ 5 Basic User Manual 3-17
Direction 2300002-100 Rev. 2
Transporting the System
Use extra care when transporting the system using vehicles. In 
addition to the instructions used when moving the system (See 
‘Moving the System’ for more information.), also perform the 
following:
1.  Only use vehicles that are designed for transport of the 
LOGIQ 5 system.
2.  Load and unload the system to a vehicle parked on a level 
surface.
3.  Ensure that the transporting vehicle...

Preparing the System for Use
3-18 LOGIQ 5 Basic User Manual
Direction 2300002-100 Rev. 2
Transporting the System (continued)
8.  Load the unit aboard the vehicle carefully and over its center 
of gravity. Keep the unit still and upright. 
NOTE:  Do not lay the unit down. 
9.  Ensure that the system is firmly secured while inside the 
vehicle. Any movement, coupled with the weight of the 
system, could cause it to break loose. 
10.  Secure system with straps or as directed otherwise to 
prevent motion...

System Positioning/Transporting
LOGIQ 5 Basic User Manual 3-19
Direction 2300002-100 Rev. 2
Wheels
Examine the wheels frequently for any obvious defects that 
could cause them to break or bind. 
Front wheels
Swivel and brake lock.
Back wheels
Swivel, swivel lock and brake lock.
Setting the lock
The pedal is located in the front wheels of the unit and  enables 
the user to control the movement of the wheels.
 Figure 3-8. Front Pedal
1. Unlock
2. Lock
1
2 

Preparing the System for Use
3-20 LOGIQ 5 Basic User Manual
Direction 2300002-100 Rev. 2
Powering the System
Connecting and Using the System
To connect the system to the electrical supply:
1.  Ensure that the wall outlet is of the appropriate type.
2.  Ensure that the power switch is turned off.
3.  Unwrap the power cable. Make sure to allow sufficient slack 
in the cable so that the plug is not pulled out of the wall if the 
system is moved slightly.
4.  Attach the power plug to the system and secure it...