GE Logiq P5 User Manual

LOGIQ 5 Basic User Manual 11-1
Direction 2300002-100 Rev. 2
Chapter 11
Vascular
Describes how to perform Vascular measurements and 
calculations. 

Vascular
11-2 LOGIQ 5 Basic User Manual
Direction 2300002-100 Rev. 2
Vascular Exam Preparation
Introduction
Measurements and calculations derived from ultrasound images 
are intended to supplement other clinical procedures available 
to the attending physician. The accuracy of measurements is not 
only determined by the system accuracy, but also by use of 
proper medical protocols by the user. When appropriate, be sure 
to note any protocols associated with a particular measurement 
or calculation....

Vascular Measurements
LOGIQ 5 Basic User Manual 11-3
Direction 2300002-100 Rev. 2
Vascular Measurements
Introduction
Vascular measurements offer several different types of 
measurement studies:
 Figure 11-1. Vascular Exam Category Touch Panel
•  Generic – Common to all applications. See ‘Generic 
Measurements’ for more information.
• Carotid
•  LEA (Lower Extremity Artery)
•  LEV (Lower Extremity Vein)
•  TCD (Trans Cranial Doppler)
•  UEA (Upper Extremity Artery)
•  UEV (Upper Extremity Vein)
• Renal 

Vascular
11-4 LOGIQ 5 Basic User Manual
Direction 2300002-100 Rev. 2
Introduction (continued)
To change an exam calc:
1. Select Exam Calcs.
The Vascular exam category allows you to choose from the 
displayed exam calcs.
2.  To select another exam calcs, press the desired exam calcs 
folder.
A vascular study is a group of the particular vessels. You can 
customize the vessel exam calcs in the configuration menu.
When you use Auto Vascular calculation, you use the vessel 
keys on the Touch Panel to...

Vascular Measurements
LOGIQ 5 Basic User Manual 11-5
Direction 2300002-100 Rev. 2
B-Mode Measurements
 Figure 11-2. B-Mode Touch Panel
NOTE:  The following instructions assume that you first scan the patient 
and then press Freeze. 

Vascular
11-6 LOGIQ 5 Basic User Manual
Direction 2300002-100 Rev. 2
%Stenosis
You can calculate % Stenosis by diameter or by area.
Diameter
NOTE:  When you use diameter to calculate the %stenosis, always take 
the measurement from a cross-sectional view of the vessel.
To calculate percent stenosis by diameter:
1.  From the Generic Touch Panel, select % Stenosis. 
2. Select %sten(Diam).
The system displays an active caliper.
3.  Make a distance measurement of the inner area of the blood 
vessel. 
The...

Vascular Measurements
LOGIQ 5 Basic User Manual 11-7
Direction 2300002-100 Rev. 2
% Stenosis (continued)
AreaTo calculate percent stenosis by area:
1.  From the Generic Touch Panel, select % Stenosis. 
2. Select %sten(Area).
The system displays a trace caliper.
3.  Make a trace measurement of the inner area of the blood 
vessel.
NOTE:  To erase an open trace, move the Trackball.
The system displays a second trace caliper. 
4.  Make a trace measurement of the outer area of the blood 
vessel.
The system...

Vascular
11-8 LOGIQ 5 Basic User Manual
Direction 2300002-100 Rev. 2
Vo l u m e
The volume calculation can be made from any of the following 
measurements: 
• One distance
• Two distances
• Three distances
• One ellipse
•  One distance and one ellipse
For details on how to make a distance measurement, See 
‘Distance measurement’ for more information.
For details on how to make an ellipse measurement, See 
‘Circumference and area (ellipse) measurement’ for more 
information.
NOTE:  IMPORTANT! If you want...

Vascular Measurements
LOGIQ 5 Basic User Manual 11-9
Direction 2300002-100 Rev. 2
Volume (continued)
To make a volume calculation using one ellipse: 
1. Select Volume.
2.  Make one ellipse measurement.
3. Select Volume.
The system displays the ellipse measurement and the 
volume in the Results Window.
To make a volume calculation using one ellipse and one 
distance: 
1. Select Volume.
2.  Make one distance measurement and one ellipse 
measurement.
3. Select Volume.
The system displays the distance and...

Vascular
11-10 LOGIQ 5 Basic User Manual
Direction 2300002-100 Rev. 2
Volume (continued)
 Figure 11-3. Volume Calculation Examples
1. One distance
2. Two distances
3. Three distances
4. One ellipse
5.  One distance and one ellipseTable 11-1: Volume Calculations 
Calc NameInput Measurements
Volume (spherical) One distance
Volume (prolate spheroidal) Two distances, d1>d2
Volume (spheroidal) Three distances
Volume (prolate spheroidal) One ellipse: (d1 major axis, d2 minor axis)
Volume (spheroidal) One...