GE Logiq 9 User Manual

Probes
LOGIQ E9 User Guide 1-21
Direction 5180302-100 Rev. 1
Probes
Introduction
Only use approved probes. 
DO NOT plug any LOGIQ 9 probes into the LOGIQ E9 system. 
Use the left-most probe port for the 3CRF and S1-5 probes; use 
the 3 right probe ports for any “___-D” probe. 
 Figure 1-13. Probe Connectors
1.  3CRF and S1-5 Probe Connector
2. _____-D Probe Connector
Refer to the Probes chapter for more information. 

Getting Started
1-22 LOGIQ E9 User Guide
Direction 5180302-100 Rev. 1
Connecting the Probe
Probes can be connected at any time, regardless of whether the 
console is powered on or off. To ensure that the ports are not 
active, place the system in the image freeze condition.
To connect a probe:
1.  Place the probes carrying case on a stable surface and 
open the case.
2.  Carefully remove the probe and unwrap the probe cord.
3.  DO NOT allow the probe head to hang free. Impact to the 
probe head could...

Probes
LOGIQ E9 User Guide 1-23
Direction 5180302-100 Rev. 1
Cable Handling 
Take the following precautions with probe cables:
•  Keep free from wheels. Use the cable hooks located below 
the operator panel. 
•  Do not bend the cable acutely
•  Avoid crossing cables between probes.
Activating the Probe
To activate the probe, select the appropriate probe from the 
probe indicators on the Touch Panel.
Figure 1-14. Probe Indicators
1. Probe Indicators
The probes default settings for the mode and selected...

Getting Started
1-24 LOGIQ E9 User Guide
Direction 5180302-100 Rev. 1
Disconnecting the Probe
Probes can be disconnected at any time. However, the probe 
should not be active when disconnecting the probe.
1.  Ensure the probe is deactivated.  Deactivate by selecting 
another probe or pressing Freeze.
2.  Move the probe locking handle to the left.
3.  Pull the probe and connector straight out of the probe port.
4.  Carefully slide the probe and connector away from the 
probe port and around the right side...

Probes
LOGIQ E9 User Guide 1-25
Direction 5180302-100 Rev. 1
LOGIQ E9 Applications
The LOGIQ E9 probes are ONLY approved for use for the 
applications listed in the table below. 
Table 1-4:  Probe Indications for Use
Probe 
Application9L
-D
11
L-
D
ML
6-
15-
D
M4
S-
D
S1
-5
C1
-5-
DM6
C-
D
3C
RF
IC
5-
9
DRN
A5
-9-
DRA
B2
-5-
DRI
C5
-9-
DRS
P6-
16-
D
Abdomen X X X X X X
Small Parts X X X X
Periph. Vasc./ 
VascularXX X X X X
Obstetrics X X X X X X X
Gynecology X X X X X X
Pediatrics X X X X X X
Neonatal X...

Getting Started
1-26 LOGIQ E9 User Guide
Direction 5180302-100 Rev. 1
LOGIQ E9 Features
Table 1-5:  Probe Features
Probe 
Application9L
-D
11
L-
D
ML
6-
15-
D
M4
S-
D
S1
-5
C1
-5-
DM6
C-
D
3C
RF
IC
5-
9-
DRN
A5
-9-
DRA
B2
-5-
DRI
C5
-9-
DRS
P6-
16-
D
Coded 
HarmonicsXX XXX XXXXX X X X
SRI-HD XX XXX XXXXX X X X
Coded 
ContrastXX XXXX X
LOGIQ View X X X X X X X X X X X X X
Virtual 
ConvexXX X X X X
Easy 3D X X X X X X X X X
Advanced 3D  X X X X X X X X X
Tru3D X X X X
4DXXXX
Raw Data X X X X X X X X X X X...

Beginning an Exam
LOGIQ E9 User Guide 1-27
Direction 5180302-100 Rev. 1
Beginning an Exam
Scanning a New Patient 
1. Press Patient. 
2. Press New Patient on the Patient menu. 
3.  If there are images on the clipboard, a pop-up menu 
appears. Specify whether you want to store images 
permanently, delete images, or go to active images. 
4.  Choose the exam category. 
5.  Verify the dataflow. 
NOTE:  DO NOT use the removable media Dataflows on the New 
Patient menu. 
NOTE:  The system can display a warning...

Getting Started
1-28 LOGIQ E9 User Guide
Direction 5180302-100 Rev. 1
Scanning a New Patient (continued)
10.  Store the raw data to the clipboard.
To store the still image, press Freeze and run the cineloop 
using the Trackball. Select the frame and press P1 (or the 
assigned Printer key).
To store the cineloop, press Freeze and run the cineloop 
using the Trackball. Select the start/end frame and run the 
selected loop. Press P1 (or the assigned Print key).
11.  When you have completed the study, press...

Beginning an Exam
LOGIQ E9 User Guide 1-29
Direction 5180302-100 Rev. 1
Patient Screen
 Figure 1-15. Patient Screen (Example: Category OB)
1. Image Management
2. Function Selection
3. EZBackup/EZMove
4. Dataflow Selection
5. Exit
6. Patient Information
7. Category Selection
8. Exam Information
9. Patient View
10. Scan Assistant Program 

Getting Started
1-30 LOGIQ E9 User Guide
Direction 5180302-100 Rev. 1
Patient Screen (continued)
Enter Patient Data with the alphanumeric keyboard.
To navigate through the Patient Entry menu, use the Tab key or 
Trackball and Set to move and fix the cursor.
The Patient Screen details are:
1. Image Management
•  Patient–Provides a search and creation of patient. 
(currently selected)
•  Image History–Provides a list of images per exam for 
the currently selected patient.
•  Active Images–Provides preview...