GE Logiq 9 User Manual

LOGIQ E9 User Guide 1-1
Direction 5180302-100 Rev. 1
Chapter 1
Getting Started
Console Overview, Moving the System, System Start-
up, Probes and Beginning an Exam 

Getting Started
1-2 LOGIQ E9 User Guide
Direction 5180302-100 Rev. 1
Console Overview
Indications for Use 
The LOGIQ E9 is intended for use by a qualified physician for 
ultrasound evaluation. Specific clinical applications and exam 
types include:
• Fetal/Obstetrics
•  Abdominal (including GYN)
• Pediatric
•  Small Organ (including breast, testes, thyroid)
• Neonatal Cephalic
• Adult Cephalic
• Peripheral Vascular
•  Musculo-skeletal Conventional and Superficial
•  Urology (including prostate)
•...

Console Overview
LOGIQ E9 User Guide 1-3
Direction 5180302-100 Rev. 1
Important Notices
Do not attempt to install the system alone. General Electric, 
Affiliate, or Distributor Field Engineers and Application 
Specialists will install and setup the system. 
NOTICE This medical equipment is approved, in terms of the prevention 
of radio wave interference, to be used in hospitals, clinics and 
other institutions which are environmentally qualified. The use of 
this equipment in an inappropriate environment...

Getting Started
1-4 LOGIQ E9 User Guide
Direction 5180302-100 Rev. 1
Important Notices (continued)
Figure 1-1. Example Plug and Outlet Configurations
1.   100-120 VAC, 1200 VA
 Plug and Outlet Configuration
2.   220-240 VAC, 1200 VA
 Plug and Outlet Configuration
WARNINGTo avoid risk of fire, the system power must be supplied from a 
separate, properly rated outlet. 
Under no circumstances should the AC power plug be altered, 
changed, or adapted to a configuration rated less than 
specified. Never use...

Console Overview
LOGIQ E9 User Guide 1-5
Direction 5180302-100 Rev. 1
Console graphics
The following are illustrations of the console:
 Figure 1-2. LOGIQ E9 System (right and left side views)
1. LCD
2.  Gel Holder / Specialty Probe Holder
3.  Operator Panel, Probe Holders with Cable 
Management
4.  Brake Release / Up/Down Controls5.  Peripherals (Black/White Printer and CD/DVD 
Drive) and Network Activity/Speed (Green=1 
Gigabyte and Yellow=100 Mb) and Hard Disk 
Drive Indicator
6. Probe Connectors
7....

Getting Started
1-6 LOGIQ E9 User Guide
Direction 5180302-100 Rev. 1
Console graphics (continued)
 Figure 1-3. LOGIQ E9 System (front and back views)
1.  Power On/Off; Operator Panel USB Ports
2.  Brake and Up/Down Controls
3.  Probe Cable Management Hooks (underneath 
Operator Panel)
4. Black/White Printer
5. CD/DVD Drive
6.  Network and Hard Disk Drive Indicators
7. Probe Connectors8. Brake Pedal
9. Rear Handle
10.  Power Cord Hooks
11.  Op Panel Up/Down Manual Release Level
12.  Access to Peripheral...

Console Overview
LOGIQ E9 User Guide 1-7
Direction 5180302-100 Rev. 1
System USB Ports
Operator PanelThe two Operator Panel USB Ports SHOULD ONLY BE USED 
for Bus-powered USB Hard Disk Drives and USB Flash Drives. 
The following configurations can be used: 
•  One or two USB Flash Drives
•  One Flash Drive and One Bus-powered Hard Disk Drive
• One Bus-powered Hard Disk Drive
Rear of SystemThe two USB ports at the back of the system SHOULD ONLY 
BE USED for the following devices: 
•  Color or Report...

Getting Started
1-8 LOGIQ E9 User Guide
Direction 5180302-100 Rev. 1
Peripheral/Accessory Connector Panel
 Figure 1-4. Peripheral/Accessory Connector Panel
Table 1-1:  Peripheral/Accessory Connector Panel Descriptions
No.ItemType of connector 
USB Ports USB 2.0
Audio In/Out ACR
DVI Port Connector DVI Analog Video Output. 
Note: Use a DVI to VGA Adapter in order to 
connect an analog monitor. 
Ethernet RJ-45 Modular, 8-pin 

Console Overview
LOGIQ E9 User Guide 1-9
Direction 5180302-100 Rev. 1
Control Panel Map 
 Figure 1-5. Control Panel
1.  Probe and Cord Holder
2. USB Ports (2)
3.  Touch Panel and Joystick controls
4. Keyboard
5. Feature Keys
6. Mode/Gain/XYZ Controls
7. TGC
8.  Trackball, Trackball Keys, Pointer, Measure, Comment, 
Body Pattern, Clear, Zoom, 3D/4D, P1
9.  L/R, Start/Stop, Freeze
10. Steer/Width/Depth/Reverse
11. Auto
12. P2, P3, P4 

Getting Started
1-10 LOGIQ E9 User Guide
Direction 5180302-100 Rev. 1
Touch Panel
Figure 1-6. Exam Function Controls
1. Patient: Enters Patient screen
2.  Scan: Enters scanning mode screen
3.  Reports: Activates default report and Touch Panel of report 
choices.
4.  End Exam: Activates Image Management and Touch Panel 
with end of exam options.
5.  Utility: Activates system configuration menus.
6.  Preset: Selects the application to use.
7.  Probe Indicator: Indicates and selects the probes.
At the...