Faroudja Fdp-Dila2 Installation And Operations Manual

61
Replacing the Light-Source Lamp 
■Resetting the Lamp Use Time
After replacing with a new light-source lamp, reset the lamp-time counter inside the projector to clear the accumulated lamp 
time to zero (0). After resetting, a new count will start for the new light-source lamp.
■Projector’s button1Turn on the MAIN POWER switch to go 
into stand-by mode.
In stand-by mode, the STAND BY indicator on the 
projector lights up.
2Press the following buttons on the 
projector, sequentially.
1Momentary press the...

62
Cleaning and Replacing the Filter Cover
Clean the filter regularly. If the filter is heavily stained and does not clean, or if it is damaged, replace the filter with a new filter. 
Otherwise, dirt may get inside and appear on the screen, preventing you from fully enjoying the video image. If dirt gets inside
or if you need information about the filter, consult authorized dealer where you purchased the projector or the nearest Service
Center.
1Turn off the MAIN POWER switch.
After the projector goes...

63
Troubleshooting
Solutions to common problems related to your projector are described here. If none of the solutions presented here solves the 
problem, unplug the projector and consult an authorized dealer or Service Center.
Symptom Probable cause Corrective action Page
Power is not 
supplied.•Is the power cord disconnected? • Insert the power cord (plug) firmly. 30
•Is the MAIN POWER switch turned 
on?•Turn on the MAIN POWER switch. 32
•Is the fuse blown? • Turn off the MAIN POWER switch and 
check...

64
Troubleshooting
* This device uses a computer. External noise may cause it to malfunction. If this happens, turn the power off, remove the 
electric plug from the wall outlet. Then insert the electric plug back into the wall outlet, turn the power back on and check the
operation.
■When warning indication is shown by the blinking indicators:
The warning status will be notified by the combination lighting of the projector’s indicators.
For the warning contents and the action to be taken, refer to...

65
Warning Indication
If something abnormal has occurred with the projector, the warning status will be indicated by the combination of lighting the 
indicators on the control panel as shown in the following table. Then, the projector automatically stops projection and runs the
cooling fan for about 120 seconds.
Warning indication table:
*For individual indicator lighting, refer to page 58.
■Action to be taken for warning indication
Stopping the projector:
After the cooling fan has stopped, take the...

66
Warning Messages
The following shows the warning messages that can be displayed on the screen. When a warning message is displayed, take 
the corrective action described here.
Message Cause Corrective action Page
•No device is connected to the 
input terminal.
•The terminal is connected but no 
signal is output from the 
connected device.
*The selected input mode (input 
terminal) name is shown in the 
first line of the massage.
•Connect a device to the selected 
terminal.
•Operate the connected...

67
Warning Messages 
•When the DIGITAL ZOOM button 
is pressed for the video signals 
that cannot be zoomed (UXGA 
60Hz, SXGA 60Hz.), this 
message appears for a few 
seconds to notify that the image 
cannot be digitally zoomed.
*To forcibly clear the message, 
press the EXIT button.
•Digital-zoom function does not 
work for the inputted video 
signals.
To use the this function, input the 
video signals that can be digitally 
zoomed.13, 37
Displayed when the lamp control 
setting is set to NORMAL MODE...

68
War ning Messages
Memo
The message display language corresponds to the menu display language setting. This is set to “English (English)” when the 
projector is bought. The display language can be selected from 6 languages. (Refer to page 46.) However, the input mode 
(PC1, PC2, DVI, Y/C, VIDEO, COMP) and button indications (FREEZE, D.ZOOM, EXIT) are only displayed in English 
irrespective of the display language setting.
The language settings in the section are explained in “English”.Displayed when...

69
Specifications
■Optical mechanism system
■Electrical system
■Input terminals
■Output terminal
•Projection method D-ILA® (Direct Drive Image Light Amplifier) method
(Reflective-type active-matrix method)
•D-ILA
® device0.9" (2.3 cm) measured diagonally (1365 pixels × 1024 pixels) × 3
(Total number of pixels : 4,193,280)
•Projecting lens GL-M2910G: 1:1
GL-M2915SG: 1.5:1 (with ±2% zooming/shift function)
GL-M2920ZG:× 1.5 zoom lens (2:1 to 3:1) (zooming function)
GL-M2930SZG:× 1.9 zoom lens (2.9 to...

70
Specifications
■General
*Design and specifications are subject to change without notice.
*D-ILA devices are manufactured with a very high-precision technology, allowing 99.99% of the pixels to be effective. Only 
0.01% or less of the pixels are missing or always on.
*For easy understanding, pictures and illustrations maybe emphasized, composed or have omissions and may be more or 
less different from actual products.
*TRADEMARKS
D-ILA is a trademark of Victor Company of Japan, Limited.
IBM and IBM PC...