Faroudja Fdp-Dila2 Installation And Operations Manual

51
Menu Operations 
Changing the Image Gamma/Aspect Ratio (Video Menu Mode Only)
The image Gamma (Down, Cinema or Up) and the aspect ratio (4:3 or 16:9) are selectable in Video menu mode. 
1Press the MENU button.
The main menu appears on the screen.
2Select “Set up” with the cursor button 5
55 5 or ∞
∞∞ ∞, and press 3
33 3 or the ENTER button.
The “Set up 1” submenu appears on the screen.
Video submenu
3Select “Gamma” or “Aspect ratio” with the cursor button 5
55 5 or ∞
∞∞ ∞.
4Adjust the image tone or...

52
Menu Operations
Changing the Image Size - Resize Function (PC Menu Mode Only)
The picture image projected can be selectable with the 
Resize function which is available only in PC menu mode.
You can choose the video image size projected from the 
following: (Factory setting is “Aspect”.)
“1:1”:The image is displayed at the input resolution. The 
picture image projected is not enlarged even if its 
number of pixels (resolution) is smaller than that of 
the projector’s D-ILA element (1365 pixels × 1024...

53
Menu Operations 
Setting and Adjusting Other Functions (OPTIONS)
Various functions are provided as shown in the “Options 1” and “Options 2” submenus.
You can set or adjust each function, as required.
1Press the MENU button.
The main menu appears on the screen.
2Select “Options” with the cursor button 5
55 5 or ∞
∞∞ ∞, and press 3
33 3 or the ENTER button.
The “Options 1” submenu appears on the screen.
3Select the item to be adjusted with the cursor button 5
55 5 or ∞
∞∞ ∞.
4Make adjustment with the...

54
Menu Operations
* Factory set value
5Press the EXIT button to return to the previous menu or press the MENU button to 
exit the menu mode.
Note
•Refer to “Removing the Trapezoidal Distortion of the Image” on page 35 for more details about adjusting the keystone. Adjustment item Button Adjustment content
Menu display2 or 3Sets whether to clear the menu display automatically or not.
15sec* : Clears the display automatically in about 15 seconds.
ON : Does not automatically clear the menu display.
Line...

55
Menu Operations 
Getting Information
You can get information on the input signal, accumulated used hours of light-source lamp, etc.
1Press the MENU button.
The main menu appears on the screen.
2Select “Information” with the cursor button 5
55 5 or ∞
∞∞ ∞.
The “Information” will be displayed in the main menu.
*No submenu can be selected.
Video main menu PC main menu
Input: Shows the terminal name selected by the VIDEO or PC button. (Y/C, VIDEO or COMP, or PC1, PC2 or DVI)
Switcher: This display...

56
Replacing the Fuse
A fuse is used to protect the power source of the projector. If the fuse is blown, replace it. When the power switch is turned on
but no power is supplied to the projector, check the fuse. If there are any unclear points, contact the dealer where you 
purchased your projector, or consult the Service center.
CAUTION
•When replacing the fuse, use the same rating and type (12 A 250 V). Otherwise, a fire may occur and/or the projector may 
be damaged.
1Turn off the main power switch and...

57
Replacing the Light-Source Lamp
■Light-source lamp and lamp use time
The light-source lamp has a service life of approximately 1000 hours.
[Average lamp life: 1000 hours (brightness half-life)]
When the light-source lamp approaches the end of its service life, degradation progresses rapidly. In NORMAL MODE, 
arrange for a new lamp (lamp unit) or replace the lamp after 900 hours. Depending on the usage conditions, the replacement 
time may be shorter.
(In LOC and LPC modes, the brightness of the lamp...

58
Replacing the Light-Source Lamp
■Projecting after the lamp has been used for more than 1000 hours (LIGHT OUTPUT 
CONTROL MODE) (LAMP POWER CONTROL MODE)
CAUTIONS
•If the projector is set up in a constricted place which is unsuitable for work, and if you perform replacement work there, this
could cause injury. Move the projector to a place large enough for work, and then replace the light-source lamp.
•Use a genuine product for the light-source lamp. If you use other than a genuine product, this could...

59
Replacing the Light-Source Lamp 
■Be sure that the power cord is unplugged from the wall outlet.
1Remove the lamp-replacement opening 
cover by loosening screws.
Loosen the two screws with a flat-end screwdriver.
Note
•The screws are fitted so that they do not come off the lamp-
replacement opening cover.
2Loosen the screws, raise the handle, 
and pull out the light-source lamp.
Loosen the two screws with a flat-end screwdriver.
Note
•The screws are fitted so that they do not come off the light-...

60
Replacing the Light-Source Lamp
3Insert the new light-source lamp fully 
inside and fasten the screws.
Fasten the two screws with a flat-end screwdriver.
CAUTION
•Do not touch the glass surface of the light-source lamp 
directly with your hand as well as staining it. If you touch 
with a bare hand, oils and other substances on your hand 
may adhere to the lamp, possibly preventing it from 
performing as specified and therefore giving a shortened 
lamp life, a darkened screen, etc. To handle a new...