Faroudja Fdp-Dila2 Installation And Operations Manual

21
Installing the Projector
Setting the Position Selecting Screw for Ceiling Mounting
When using the projector in an upside-down, ceiling-mounted position (inverted top-to-bottom and right-to-left), the “position 
selecting screw for ceiling mounting” must be turned to switch to ceiling mounting.
This will correct variance in color images (shading), which otherwise would occur in ceiling mounting.
To revert to normal desktop setting, turn the “position selecting screw for ceiling mounting” back to the...

22
Connecting to Various Devices
Before connection, be sure to turn off the projector and connected devices.
Read the manual which comes with each device thoroughly.
Signals that Can Be Input to the Projector
The following signals can be input to the projector:
■Video signals
(1) Response to color systems
*1:Responds if Y/C output is available.
*2:Signifies that component signals (“Y, P
B, PR” / “Y, B-Y, R-Y” / “G, B, R, H/CS, V”) conform to the signal timing 
(synchronization and video period) of each...

23
Connecting to Various Devices
■Allowable input signals
*A signal that can be input by DVI (V-sync 85Hz is not supported.)
Notes
•The resolution for the input signals is listed in the above table.
•Even signals in the frequency range that can be input may not be displayed normally depending on the type of the signal.
•When a signal other than listed above is input, the image could be partially erased or an unneeded fold-over image could 
appear.
•Some signals other than listed above can be displayed....

24
Connecting to Various Devices 
Connecting to Video Devices
Before connection, be sure to turn off both the projector and video device.
•Read thoroughly the manual that comes with each video device.
•Use the supplied video cable. An video cable with an S-video (Y/C) terminal is not supplied.
Notes
•Connect a composite image signal output device or Y/C (S-video) image output device.
•When connecting the S-video cable, refer to “How to attach the ferrite core” on page 29.
Memo
•When connecting a...

25
Connecting to Various Devices
Connecting to HDTV Devices/DVD Players
Before connecting, be sure to turn off both the projector andHDTV devices/DVD players.
•Thoroughly read the manual that comes with eachHDTVdevice or DVD player.
•Use separately available BNC cables to connect HDTV devices and DVD players.
Note
•Connect a component signal output device or DTV-format signal output device.
Memo
•Other devices with component signal output terminals (DVD player (NTSC), etc.) can be connected.
(*DVD:...

26
Connecting to Various Devices
Connecting to Devices which Control the Projector
Before connection, be sure to turn off both the projector and devices to be connected.
•Read thoroughly the manual that comes with each device to be connected.
•By connecting a computer to the RS-232C terminal, you can control the projector. Also, you can make an infrared remote 
sensor extension unit and connect it to the REMOTE terminal of the projector.
*Obtain connection cables as required. Use a reverse connection...

27
Connecting to Various Devices 
Connecting to Computer Devices
Before connection, be sure to turn off both the projector and computer devices.
•Read thoroughly the manual that comes with each device.
■Connection to an IBM PC or IBM-compatible computer
•Use the supplied personal computer connection cable. Also, prepare cables required for connecting the devicesconnected.
Computer signals can either be connected directly to the projector or sent as pass-through tothe Video Processor.
Y
P
B/B-Y
P
R/R-Y...

28
Connecting to Various Devices
Connecting to DVI
Before connection, be sure to turn off both the projector and computer devices.
•Read thoroughly the manual that comes with each device.
Note
•Other connections are the same as in the connection example for IBM PC or IBM compatible PCs.
How to attach the ferrite core
Attach the ferrite core when using the S-video cable or infrared remote sensor extension unit which are sold separately.
ony if they are connected directly to the projector.
1Release the...

29
Connecting to Various Devices 
Connecting the Power Cord
After all devices have been finished being connected, connect the supplied power cord. At this time, do not yet turn on the 
MAIN POWER switch.
CAUTIONS
To prevent fire and electric shock, observe the 
following:
•When you do not use devices, pull out their power cords 
from wall outlets.
•Do not connect the devices with power cords other than 
those supplied.
•Do not use mains voltage other than the power voltage 
indicated.
•Do not scar,...

30
Basic Operations
■Lamp control settings
After turning the power on, first perform the lamp control settings on the setting menu referring to “Setting and Adjusting Other 
Functions (OPTIONS)” on page 54.
There are 3 modes in the lamp control settings.
1: NORMAL MODE (Normal)
Used as a normal lamp.
The projector is set to “Normal” mode at the time of purchase.
*“Lamp replacement” appears on the screen when the lamp use time exceeds 1000 hours.
2: LIGHT POWER CONTROL MODE (LPC)
Automatically controls...