Home > Epson > Printer > Epson Stylus Pro 9700 User Manual

Epson Stylus Pro 9700 User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Epson Stylus Pro 9700 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1734 Epson manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							61
    Handling Paper and Other Media|61
    Setting Up Automatic Media Tracking and Identification
    Before you load roll paper in the printer, you can set up the automatic media 
    tracking system. This system prints a barcode on the edge of the paper that 
    indicates the media type, roll length, and the alert setting. 
    When the printer is turned on or roll paper is placed in the printer, the 
    barcode is scanned and the amount of roll paper remaining is displayed on 
    the LCD panel. You will see an alert message when the roll is nearly used up.
    The barcode is printed when you press the   Paper release (ePlaten) 
    button.
    Make sure 
    PAPER OUT appears on the control panel. Then follow these 
    steps to set up the automatic media tracking system:
    1. Press r 
    Menu. 
    2. Press u or d to select 
    PAPER SETUP, then press r.
    3. Press r to select 
    ROLL PAPER REMAINING. 
    4. Press r to select 
    REMAINING PPR SETUP. 
    5. Press d, select 
    ON, and press OK.
    6. Press l to go back to 
    REMAINING PPR SETUP.
    7. Press d to select 
    ROLL PAPER LENGTH. 
    8. Press r, then select the length of the roll paper loaded in the printer, 
    from 15 to 300 ft (5 to 99.5 m), then press 
    OK.
    9. Press l, then press d to select 
    ROLL LENGTH ALERT. 
    10. Press r, then select the length at which you want to receive an alert 
    message, from 3 to 50 ft (1 to 15 m), then press 
    OK.
    11. Press   to exit the menu. 
    Tip: You can use 
    Maintenance mode to 
    switch the units of 
    measurement in the 
    printer from meters to 
    feet. See page 162 for 
    instructions.
     
    						
    							62
    62|Handling Paper and Other Media
    Placing the Paper in the Printer
    1. Open the roll paper cover. 
    2. Push the lock lever down firmly, then move the roll paper holder to the 
    left.
     
    						
    							63
    Handling Paper and Other Media|63
    3. Place the roll on top of the printer.
    4. If necessary, adjust the roll media adapters to fit the core size of the roll 
    paper.
    2-inch core:
    3-inch core:
     
    						
    							64
    64|Handling Paper and Other Media
    5. Release the tension lever on both adapters.
    6. Push the adapters into the paper core at both ends of the roll. Then pull 
    down the tension levers.
     
    						
    							65
    Handling Paper and Other Media|65
    7. Move the roll paper to the right side until it touches the roll paper guide.
    8. Slide the roll paper holder to align the left adapter with the u on the 
    holder.
     
    						
    							66
    66|Handling Paper and Other Media
    9. Roll the paper slowly into position.
    10. Slide the roll paper holder to the right to secure it in the printer. Make 
    sure both ends of the roll paper are secured in the adapters.
     
    						
    							67
    Handling Paper and Other Media|67
    11. Pull up the lock lever to lock the paper in place.
    12. If the   Paper release light is not on, press the   Paper release 
    button.
    Loading the Paper for Printing
    1. Insert the paper into the slot and pull it down.
     
    						
    							68
    68|Handling Paper and Other Media
    If the paper doesn’t come out, you may need to lower the suction by 
    pressing the dPaper Feed button. Make sure you return the suction to 
    normal after the paper is loaded.
    2. Close the roll paper cover.
    3. Press the   Paper release button.
    4. Press the   button to move the paper into printing position or wait 
    for the paper to move into position automatically.
    5. If you see a question on the display about paper settings, select 
    Yes if the 
    settings are correct, or select 
    No, then change the settings. 
    6. Press 
    OK.
    7. If the edge of the paper is uneven or folded, press the   Paper cut 
    button to cut the edge.
    To avoid indenting or creasing the paper, remove it from the paper path and 
    roll it up when you are not printing. 
    Note: Opening the front 
    cover causes printing to 
    stop. Do not open the 
    front cover while printing 
    is in progress, or your 
    print quality might be 
    affected.
     
    						
    							69
    Handling Paper and Other Media|69
    Cutting Paper Manually with the Built-in Cutter
    When you’re not using the Auto Cut On setting, you can cut roll paper 
    manually by pressing a button after your print job is finished. You can use 
    the   Paper cut button to cut most types of paper. 
    1. Before you print, press the lPaper Source button until you see the 
    roll (Auto Cut Off) icon on the LCD display.
    2. Run your print job. 
    3. Press and release the   Paper cut button. When the selection menu 
    appears, select 
    CUT, then press OK. The paper is cut.
    4. If the paper cannot be cut by the built-in cutter, press the d button to 
    feed the paper to the manual cutting position. Then cut it manually.
    Printing Trim Lines
    You can print trim lines on the right edge of your pages (Auto Cut On) or 
    on the right and bottom edge (Auto Cut Off). 
    1. Press r 
    Menu. 
    2. Press r 
    Menu again to select the Printer Setup menu. 
    3. Press d to select 
    PAGE LINE, then press r. 
    4. Press d or u to select 
    ON.
    5. Press 
    OK to save the setting. A check mark appears next to ON.
    6. Press  to exit the menu. 
    You can also specify trim lines from your printer driver software. For 
    instructions, see page 96 (Windows), or pages 121 or 134 (Mac OS X).
    Note: The built-in cutter 
    might not be able to cut 
    some types of non-Epson 
    media.
     
    						
    							70
    70|Handling Paper and Other Media
    Removing Paper from the Printer
    1. Open the roll paper cover.
    2. Press the   Paper release button to release the paper.
    If automatic media tracking is on, the barcode and paper 
    information is printed.
    If you are not using the Auto Take-Up Reel, the paper is rewound 
    automatically.
     
    						
    All Epson manuals Comments (0)

    Related Manuals for Epson Stylus Pro 9700 User Manual