Epson Projector Powerlite 5000 User Manual

Menu itemDescription
ColorAdjusts the whiteness of the screen. The H setting provides a cold
Temperaturewhite, M a standard white, and L a warm white.
To set the color temperature setting more precisely, press the right
arrow button past H, M, and L to select the User item. This displays
a screen showing USER RED and USER BLUE. Use the up and
down pointer buttons to select the color you want to adjust, and
then use the left and right buttons (control panel) or the pointer
button (remote) to change the...

Menu itemDescriptionView ChangeSpecifies the screen switching effect to use when the input source
is changed.
OffNo screen switching effect.
Upper Left
Lower RightOriginal source screen shrinks from upper left to
lower right, and new source screen expands from
upper left to lower right.
Left-Right:Original source screen shrinks from left to right, and
new source screen expands from left to right.
Outside-
MiddleOriginal source screen shrinks from outside in, and
new source screen expands from inside...

To open the Custom menu, press the top multi-purpose button or
select CUSTOM from the Main menu. ZOOM is highlighted and the
words PRESENT SET are displayed after it. Refer to the table below
for a description of the various zoom functions.
To change PREVIEWor STROBE settings, select the function you
want, then press the top multi-purpose button.
The Custom menu functions are:
Menu itemFunctionDescriptionZoomPress the bottom multi-purpose button then check
if the value next to the Zoom menu is New Set...

Menu itemFunctionDescriptionPreview
StrobeZoom ScreenPress the pointer button to zoom in on a portion of
Shiftthe enlarged display. You can move the image up,
down, left, right, and diagonally to closely view any
part of the display.
Press the bottom multi-purpose button then check
if the value next to the Preview menu is New Set or
Present Set. If the value is New Set, press the
bottom multi-purpose button to toggle the value.
Press the Custom button to turn on the Preview
function. The preview function...

Menu itemFunctionDescriptionReturnNumber ofPress the top multi-purpose button while the strobe
Frames, Timeeffect is running to display a screen specifying the
number of frames flashed and the time interval
between them. You can specify the number of
frames as 4, 9, or 16, and the time interval from
0.1 to 1 second in 0.1 second increments.
Press the top multi-purpose button again to cleat
the setting screen.
Saves your changes and displays the Main menu.
Menu Options 

3 l Using the Projector Menus 

Using the ELP Link II
Software
TheELP Link II software is a utility you can run from your desktop
or laptop computer to control projector features and configure special
effect buttons on the remote control. 

Installing the Software
ELP Link II software can be used with the following operating systems:
l Windows 3.x
l Windows 95
lMacintosh OS System 7.
Connecting Needed Cables
Before installing the software, make sure the projector is properly
connected to your computer. See Chapter 1, “Installation,” for
instructions about how to install the serial and mouse cables needed to
use the Link II software.
Installing the Software from Windows 3.x
Perform the following steps to set up the software for Windows...

2.In the Windows Program Manager, click on the File menu, then
on Run. The Run dialog box appears:
3. Type A:\SETUP (or B:\SETUP
as appropriate), then press Enter
or click OK. The ELP Link II introduction appears.
4. Press C to continue.
5.To accept the default location for where the software should be
installed, press C to continue. Otherwise, enter a new directory
name and then press C.
6.The Link II software communicates with the projector using the
computer’s serial communication (COM) port. Specify...

8.You see a prompt to create the installation directory you specified
in step 5. Press Y (yes).
Installing the Software from Windows 95
Perform the following steps to set up the software for Windows 95.
1.Insert the Link II for Windows installation diskette into a diskette
drive (A: or B: as appropriate).
2. Click Start
3.Click the Run menu option. The Run dialog box appears:
4. Type A:\SETUP (or B:\SETUPas appropriate), then press Enter
or click OK. The ELP Link II introduction appears.
5. Press C to...