Epson Projector Powerlite 5000 User Manual

Cleaning the Air Filter
Clean the air filter at the bottom of the projector after every 100 hours
of use. If it is not cleaned periodically, it can become clogged with
dust, preventing proper ventilation. This can cause overheating and
damage the projector. To clean the air filter, follow these steps:1.Turn off the projector and unplug the power cable.
2.Turn the projector on its right side so that the handle is on top
and you can access the filter easily.
Note: Standing the projector with the handle at...

4.The filter is attached to the inside of the filter cover. It is
recommended that you use a small vacuum cleaner designed for
computers and other office equipment to clean the filter. If you
don’t have one, use a dry, lint-free cloth.
If the dirt is difficult to remove or if the filter is torn, replace it.
Contact your PowerLite 5000 dealer or call EPSON Accessories at
(800) 873-7766 in the United States and Canada to obtain a new
one. Request part number 1023658.
Replacing the Lamp
The projector lamp...

3.Use a screwdriver, coin, or similar object to loosen the two
retaining screws on the lamp cover. When the screws are loose, lift
off the lamp cover. (You cannot remove these screws.)
4.Use a screwdriver, coin, or similar object to loosen the two screws
holding the lamp in position. (You cannot remove these screws.)
Replacing the Lamp 

5.Lift up the handle and pull out the lamp.
6.Gently insert the new lamp by lowering it into position. Make sure
it is inserted securely.
7.Tighten the screws you loosened in step 4.
8.Replace the lamp cover and tighten the cover screws. (Make sure
the lamp cover is securely fastened. The projector turns itself off if
the lamp cover is open.)
5 l Maintenance 

Troubleshooting
Thischapter describes the problems indicated by the warning lights
and provides information on how to solve problems with the projector.
It is divided into the following sections:
lProblems with the projector. See this section if the projector is not
working and to find out what the warning lights are indicating.
lProblems with the screen image. See this section if you cannot
project an image or if the screen image is not good.
If you have a problem, check the appropriate section and...

Problems with the Projector
If you have problems with the projector, first turn it off and unplug it.
Then plug the power cord back in and turn on the projector. If this
does not solve the problem, check the warning lights at the top of the
projector. These lights alert you to problems with projector operation.
IndicatorColorPowerRedMeaning
The projector is hot.
Projection lampRedThe lamp needs to be replaced. (See ” Replacing
the Lamp” in Chapter 5 for instructions.)
BothFlashing redThe projector is...

DThe projection lamp light is flashing orange and you cannot turn on
the projector.The lamp is cooling down. Wait until the light turns off and then turn
on the projector.
DThe power light does not come on.Turn off the projector, check that the power cable is connected
securely both at the power outlet and the projector, and press the
Power button again.
DProjected images get darker or start to deteriorate, or the projection
lamp light is red.Replace the projector lamp as described on page 84
D The power...

DThe projection lamp and power lights are flashing at the same time.An abnormality may have occurred in the projector. Turn off the
projector and unplug the power cord. Then plug the power cord back
in and turn on the projector. If nothing changes, call the service center.
+Warning: Except as specifically explained in this User`s Guide, do not
attempt to service this product yourself:
Problems with the Image or Sound
DAn image does not appear on the screen.Check that the power light is on and the lens...

You also may need to modify existing presentation files if you created
them for a different resolution. See your software manual for specific
information.D The message NO SIGNAL is displayed.
An image source not connected to the projector is selected, the signal is
not being output from the computer, or the signal is not reaching the
projector. Make sure the connectors are securely attached to both the
projector and the image source. Then check that the image source is
selected correctly. When NO SIGNAL...

DThe colors of the image are not right.The color balance may be incorrect. If you’re displaying a computer
image, adjust the red, green, and blue settings in the Video menu. If
you’re displaying video, adjust the color and tint (NTSC only) settings
on the Video menu.
D There is no sound.First check that the volume setting is not turned all the way down and
that the audio/visual cable is securely attached to both the projector
and the audio source.
The wrong source is selected. Press either the Computer...