Epson Projector Powerlite 5000 User Manual

Connect the main cable. The main cable connects the mouse cable
(needed to use the remote control as a mouse) and serial cable
(needed to use the ELP Link II software and the Effects buttons on
the remote control) to the projector.a.Connect the small end of the main cable to the projector’s
Mouse/Corn 1 port. (Use the Mouse/Corn 2 port if you are
connecting a second computer.)
b.Connect one end of the PS/2 mouse cable included with the
projector to the mouse terminal on the square end of the main
cable....

c.Connect the other end of the PS/2 mouse cable to the mouse
port on your laptop.d.If your laptop uses a serial mouse, perform steps b and c using
the serial mouse cable instead of the Ps/2 mouse cable (not
shown in the illustration).
e.To configure the projector from your laptop using the
ELP Link II software or to use the Effects buttons on the
remote control, connect one end of the serial cable to the serial
terminal on the square end of the main cable.
f.Connect the other end of the serial cable to...

3.Connect the audio cable.a.Connect one end of the audio cable to the Audio In 1 jack on
the projector. (Use the Audio In 2 jack if you are connecting a
second computer).
b.Connect the other end of the audio cable to your laptop.
Connecting to a Computer 

Connecting to aDesktop Macintosh
Before beginning, turn off the projector and Macintosh if they are on.1.Connect the video cables.
video-out cable
Note: Macintosh computer configurations vary. See your computer
manual for the location of the ports needed to connect your
PowerLite 5000 projector.
a.Connect either end of the video cable to the projector’s
Computer In 1 port. (Use the Computer In 2 port if you are
connecting a second computer.)
b.Remove the small cover and set the DIP switches on the...

c.Connect the small terminal of the Macintosh video adapter to
the other end of the video cable.d.Disconnect the monitor cable from the video port on the back
of the Macintosh and connect the video cable (with Macintosh
video adapter attached) to the video port. If a video-out cable
was supplied with your Macintosh, connect one end to the
video adapter and the other end to the video port on your
Macintosh.
e.If you wish to view or check images on the computer’s
monitor, attach the Macintosh monitor...

2.Connect the main cable. The main cable connects the mouse cable
(needed to use the remote control as a mouse) and serial cable
(needed to use the ELP Link II software) from your Macintosh to
the projector.
a.Connect the small end of the main cable to the projector’s
Mouse/Corn 1 port. (Use the Mouse/Corn 2 to connect a
second computer.)
b.Connect the MAC mouse cable to the mouse terminal on the
other end of the main cable.
1 l Installation 

3c.Disconnect the mouse cable from the ADB port of the Macin-
tosh and connect the mouse connector of the MAC mouse
cable to the mouse port.
d.If you are planning to use the ELP Link II software, connect
either end of the serial cable to the serial terminal on the large
end of the main cable. Connect the other end of the serial
cable to the PRINTER or MODEM port on the back of your
Macintosh.
e.Tighten the screws on both connectors.
Connect the audio cable.
a.Connect one end of the audio cable to the...

Connecting to a PowerBook
Your PowerBook must have a video-out capability in order to connect
to the PowerLite 5000 projector.
Before beginning, turn off the projector and computer if they are on.1.Connect the video cable.
video-out
Note: PowerBook configurations vary. See your computer manual for
the location of the ports needed to connect your PowerLite 5000
projector.
a.Connect one end of the video cable to the projector’s
Computer In 1 port. (Use the Computer In 2 port to connect
a second computer.)...

b.Remove the small cover and set the DIP switches on the
Macintosh video adapter in accordance with the resolutions
you want to use (such as 16 inch mode).
c.Connect the small terminal of the Macintosh video adapter to
the other end of the video cable.d.Connect one end of the video-out cable that came with your
Power-Book to the video-out connector on the back of the
Power-Book.
e.Connect the other end of the Power-Book video-out cable to
the projector video cable (with Macintosh video adapter...

Connect the main cable. The main cable connects the mouse cable
(needed to use the remote control as a mouse) and serial cable
(needed to use the ELP Link II software) to the projector.a.Connect the small end of the main cable to the projector’s
Mouse/Com 1 port. (Use the Mouse/Com 2 port if you are
connecting a second computer.)
b.Connect the MAC mouse cable to the mouse terminal on the
other end of the main cable.
c.Connect the mouse connector of the MAC mouse cable to the
mouse port on the back of the...