Epson Projector Emp 7100 User Manual
Have a look at the manual Epson Projector Emp 7100 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1734 Epson manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
73 To clean the air filter: 1. Switch the projector off and unplug the power cable from the wall socket. 2. Stand the projector with the handle at the top so that the filter is easily accessible. uCaution: Stand the projector with the handle at the top to prevent dust from entering the projector. 3. Lift the stopper of the filter cover with your fingers. Cleaning the Air Filter 1 2 filter
745 ¥ Maintenance 4. The air filter is attached to the inside of the filter cover. To clean the filter you are advised to use a small vacuum cleaner designed for computers and other office equipment. If you do not have one, use a dr y, lint-fr ee cloth. If the dirt is difficult to remove or if the filter is torn, replace it. Replacement lamps come with an air filter. Contact your EMP dealer or call an EPSON Service Centre. Be sure to request par t number. 5. Replace the filter. 6. Plug the power cable back into the wall socket. Replacing the Lamp The projector lamp typically lasts for about 2000 hours of use. Replace the projector lamp whenever any of the following situations occur. We recommend you to purchase a spare lamp since the projector lamp may exhaust before its normal life depend on each lamp characteristic and usage. ¥Whenever you feel the projected image is too dark or dim, even though the current projector lamp has not reached the end of its life. ¥Whenever the REPLACE LAMP indicator appears on the screen when the projector lamp comes on. ¥Whenever the lamp indicator flashes orange and red alternately to indicate that the projector lamp has reached the end of its life. ¥Whenever the lamp indicator lights up red or the projector lamp fails to light.
75 Contact your local EPSON dealer for a replacement lamp. Use only replacement lamp part number. u Note: Be sure to always use a new projector lamp. Otherwise the projector lamp operating time display will indicate incorrect information. u Warning: Allow the lamp to cool down before replacing it. During use, it becomes hot enough to burn you. 1. Switch off the projector and disconnect the power cable from the wall socket. 2. Use a screwdriver, coin or similar object to loosen the two retaining screws on the lamp cover. You cannot remove these screws. 3. When the screws are loose, lift off the lamp cover. Replacing the Lamp lamp cover
765 ¥ Maintenance 4. Use a screwdriver, coin or similar object to loosen the two screws holding the lamp in position. You cannot remove these screws. 5. Lift up the handle and pull out the lamp. screws
77Replacing the Lamp uCaution: When you replace the lamp never touch the new lamp with your bare hands. The invisible residue left by the oil on your hands may shorten the lamp life. Use a cloth or gloves when handling the new lamp. 6. Gently insert the new lamp by lowering it into position. 7. Tighten the screws you loosened in step 5. 8. Replace the lamp cover and tighten the cover screws. Make sure the lamp cover is securely fastened. The projector turns itself off if the lamp cover is open. 9. When replacing the bulb you should also replace the air filter attached to the lamp.
79 Troubleshooting This chapter describes the problems indicated by the status lights and provides information on what to do if you experience problems with the projector. It is divided into the following sections: ¥General pr oblems with the projector. Refer to this section if the projec- tor is not working and to find out what the warning lights are indicating. ¥Problems with the screen image. Refer to this section if you cannot project an image or if the quality of the screen image is poor. If you have a problem, refer to the appr opriate section and follow all the suggestions which apply to your problem. If none of the suggested solu- tions solves the problem, call your EMP-7100/5100 dealer or call the EPSON Service Centre. 6
806 ¥ Troubleshooting Problems with the Projector If you are having problems with the projector, first check the indica- tors on the projector. Operation Indicator Color Status Meaning Off Projector is off. Orange Lit Sleep mode Green Lit Projection lamp is lit and projector is projecting. Orange Flashing The projector is hot. Red Flashing Internal projector problem Red Lit The projector is too hot and turned off. Projection Lamp Indicator Color Status Meaning Off Projector is off. Green Lit Projection lamp is lit. Green Flashing The projector is warming up. Orange Flashing Projection lamp is reaching the end of its life and Red alternately and should be replaced with a new one. Orange Flashing The projector is cooling. Red Lit Projection lamp has reached the end of its life and will no longer project images. Replace the projection lamp with a new one. Red Flashing Projection lamp or lamp power supply problem.
81 The following describes some common problems and what you should do when you encounter them. zThe operation indicator does not light up. Check the power supply, making sure that the power cable is secur ely connected to the projector and the power outlet. Check to ensure that the projector lamp cover is securely closed. zThe projector lamp does not light up. The lamp is bur ned out and needs to be replaced. zThe operation indicator is red. The projector is overheated. The projector lamp will also tur n off automatically at this time. Wait until the projector cools off before you tr y tur ning it back on. Check the air vents on the bottom and back of the projector to make sur e they are not blocked. If they are, use the procedure described on page 75 to clean the filters. If the projector continues to overheat after you clean the filters, you may have to request ser vicing for the cooling fan or internal circuitry. Contact your nearest service provider. zThe operation indicator is flashing red. Ther e is a problem with the projectorÕs internal circuitry that requires ser vicing. Contact your nearest service provider. zThe projection lamp indicator is red. The projection lamp has reached the end of its life and needs to be replaced. Problems with the Projector
826 ¥ Troubleshooting zThe projection lamp indicator is flashing red. Replace the projection lamp with a new one and turn the projector back on. If this does not solve the pr oblem, there is a problem with the projector lampÕs internal circuitry that r equires ser vicing. Contact your nearest service provider. zImportant! Never tr y to per form any maintenance on the projector that is not specifically covered in this manual.