Epson Projector BrightLink Pro 1430Wi User Manual

4. Select the
Administrator Settings menu and pressEnter, then select Mail Notificationand press
Enter.
5. Enter the IP address for the SMTP Serveroption.
Note: Do not use these addresses: 127.x.x.x or 224.0.0.0 through 255.255.255.255 (where x is a
number from 0 to 255).
6. Select a number for the SMTP server Port Number, from 1 to 65535 (default is 25).
7. Choose an Email Address field, enter the e-mail address, and select the alerts you want to receive
there. Repeat for up to three addresses.
Note:...

Parent topic:
Using the Projector on a Network
Network Projector E-mail Alert Messages When a problem occurs with a networked projector, and you selected to receive e-mail alerts, you
receive an e-mail containing the following information:
•Epson Projector on the subject line
• The name of the projector experiencing a problem
• The IP address of the affected projector
• Detailed information about the problem
Note: If a critical problem causes a projector to shut down, you may not receive an e-mail...

4. Select the
Administrator Setting menu and pressEnter, then select the SNMPmenu and press
Enter.
5. Enter up to two IP addresses to receive SNMP notifications, using 0 to 255 for each address field. Note: Do not use these addresses: 127.x.x.x or 224.0.0.0 through 255.255.255.255 (where x is a
number from 0 to 255).
6. Enter the community name of SNMP (up to 32 single-byte alphanumeric characters).
7. When you finish selecting settings, select Setup Completeand follow the on-screen instructions to
save...

Note:
If you want to use a web browser to select settings when the projector is turned off, you need to
adjust the Standby Mode settings in the ECO menu.
1. Make sure the projector is turned on.
2. Start your web browser on a computer connected to the network.
3. Type the projectors IP address into the browsers address box and press the computers Enterkey.
You see the Web Control screen and a prompt to enter a user ID and password.
4. Enter the following information in uppercase or lowercase letters,...

2 Captures the projected image. Switch to whiteboard mode to paste the image into a new
page.
3 Prints the projected image.
4 Freeze button control
5 A/V Mute button control
6 Page Up andPage Down button controls
7 Searches for sources
8 Switches to whiteboard mode.
9 Saves the projected image in .png format.
10 Volume button controls
11 Closed Caption control
7. Select the icon corresponding to the projector function you want to control.
Parent topic: Using the Projector on a Network
Related references...

2. Open a web browser and connect to the projector by entering the IP address of the projector.
Note: You can find the projectors IP address in the projectors Network menu.
3. Enter the user name and password at the prompts.
4. Select the configicon.
Note: This icon does not appear when you connect from a computer.
The Web Control page is displayed.
5. Select Whiteboard Settings >Administrator Settings >Address Book Settings >Address
Book File and select the Choose Filebutton.
6. Select the address book...

• For the password, enter the default password
admin. (You can change the Web Control password
using the projectors Network menu.)
5. Under Whiteboard Settings, select Administrator Settings.
You see a screen like this:
6. Under Template Settings, select the number of the template you are uploading.
7. Select the Browsebutton, select the .png image on your computer, and select Open.
8. Select Setto upload the template to the projector.
Parent topic: Using the Projector on a Network
Crestron RoomView...

Setting Up Crestron RoomView Support
Controlling a Networked Projector Using Crestron RoomView
Parent topic:
Using the Projector on a Network
Setting Up Crestron RoomView Support To set up your projector for monitoring and control using a Crestron RoomView system, make sure your
computer and projector are connected to the network.
Note:If you want to use the Crestron RoomView system when the projector is turned off, you need to
adjust the Standby Mode settings in the ECO menu.
1. Press the Menubutton.
2....

Parent topic:
Crestron RoomView Support
Controlling a Networked Projector Using Crestron RoomView Once you have set up your projector to use Crestron RoomView, you can control and monitor projection
using a compatible web browser.
1. Start your web browser on a computer connected to the network.
2. Type the projectors IP address into the browsers address box and press the computers Enterkey.
You see this screen:
3. Select the input source that you want to control in the Sources List box. You can scroll...

7. When you finish selecting settings, click
Exitto exit the program.
Parent topic: Crestron RoomView Support
110