Epson Projector BrightLink 536Wi User Manual

6. Grasp the raised section of the lamp and gently pull the lamp out of the projector.
Note: The lamp(s) in this product contain mercury. Please consult your state and local
regulations regarding disposal or recycling. Do not put in the trash.
171   

7. Gently insert the new lamp into the projector. If it does not fit easily, make sure it is facing the right
way.
Caution: Do not touch any glass on the lamp assembly to avoid premature lamp failure.
172  

8. Push in the lamp firmly and tighten the screws to secure it.
Caution: Do not over-tighten the screws.
9. Replace the lamp cover and tighten the screw to secure it.
173   

Note:
Be sure the lamp cover is securely installed or the lamp will not come on.
Reset the lamp timer to zero to keep track of the new lamp’s usage.
Parent topic: Projector Lamp Maintenance
Related tasks
Resetting the Lamp Timer
Resetting the Lamp Timer You must reset the lamp timer after replacing the projectors lamp to clear the lamp replacement
message and to keep track of lamp usage correctly.
Note:Do not reset the lamp timer if you have not replaced the lamp to avoid inaccurate lamp usage...

6. Press
MenuorEsc to exit the menus.
Parent topic: Projector Lamp Maintenance
Related references
Projector Reset Options - Reset Menu
Related tasks
Replacing the Lamp
Replacing the Remote Control Batteries The remote control uses two AA manganese or alkaline batteries. Replace the batteries as soon as they
run out.
Caution:Use only the type of batteries specified in this manual. Do not install batteries of different types,
or mix new and old batteries.
1. Remove the battery cover as shown.
2. Remove the...

3. Insert the batteries with the
+and –ends facing as shown.
4. Replace the battery cover and press it down until it clicks into place. Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat
or flame. Keep batteries out of the reach of children; they are choking hazards and are very
dangerous if swallowed.
Parent topic: Projector Maintenance
Transporting the Projector The projector contains precision parts, some of which are glass. Follow these guidelines to...

• When transporting the projector a long distance or as checked luggage, pack it in a firm box with
cushioning around it and mark the box Fragile.
• When shipping the projector for repairs, place it in its original packing materials, if possible, or use equivalent materials with cushioning around the projector. Mark the box Fragile.
Note: Epson shall not be liable for any damages incurred during transportation.
Parent topic: Maintaining and Transporting the Projector
177 

Solving Problems
Check the solutions in these sections if you have any problems using the projector.
Projection Problem Tips
Projector Light Status
Using the Projector Help Displays
Solving Image or Sound Problems
Solving Projector or Remote Control Operation Problems
Solving Interactive Problems
Solving Network Problems
Where to Get Help
Projection Problem Tips If the projector is not working properly, try turning it off and unplugging it. Then plug it back in and turn it
on.
If this does not solve the...

Projector Light Status
The lights on the projector indicate the projector status and let you know when a problem occurs. Check
the status and color of the lights and look for a solution in the table here.
1 Power light
2 Status light
3 Lamp light
4 Temp (temperature) light
Power light Status light Lamp light Temp light Status and solution
Blue BlueOff Off Normal operation.
Blue Flashing blue Off Off Warming up. Wait for an image to
appear.
Blue OffOff Off Standby or sleep mode.
Blue Flashing blue Off Off...

Power light Status light Lamp light Temp light Status and solution
Blue
Varies Off Flashing Projector is too hot.
orange• Make sure that the vents and air
filter are not clogged with dust or
obstructed by nearby objects.
• Clean or replace the air filter.
• Make sure the environmental temperature is not too hot.
Off Flashing blue Off Orange Projector has overheated and turned
off. Leave it turned off to cool down.
After about five minutes, do the
following:
• Make sure that the vents and airfilter are...