Epson Projector BrightLink 536Wi User Manual

Setting a Password
To use password security, you must set a password.
1. Hold down the Freezebutton on the remote control for about ten seconds or until you see this menu.
2. Press the down arrow to select Passwordand pressEnter.
You see the prompt Change the password?.
3. Select Yesand press Enter.
4. Press and hold down the Numbutton on the remote control and use the numeric buttons to set a
four-digit password.
The password displays as **** as you enter it. Then you see the confirmation prompt.
5....

6. Press
Escto return to the menu.
7. Make a note of the password and keep it in a safe place in case you forget it.
Parent topic: Password Security Types
Selecting Password Security Types After setting a password, you see this menu, allowing you to select the password security types you want
to use.
If you do not see this menu, hold down the Freezebutton on the remote control for about 10 seconds or
until the menu appears.
1. To prevent unauthorized use of the projector, select Power On Protection,...

Entering a Password to Use the Projector
If a password is set up and a Power On Protectionpassword is enabled, you see a prompt to enter a
password whenever you turn on the projector.
You must enter the correct password to use the projector.
1. Press and hold down the Numbutton on the remote control while you enter the password using the
numeric buttons.
The password screen closes.
2. If the password is incorrect, the following may happen: • You see a wrong password message and a prompt to try again....

• If you enter an incorrect password several times in succession, the projector displays a request
code and a message to contact Epson Support. Do not attempt to enter the password again.
When you contact Epson Support, provide the displayed request code and proof of ownership for
assistance in unlocking the projector.
Parent topic: Password Security Types
Related references
Projector Setup Settings - Extended Menu
Saving a Users Logo Image to Display You can transfer an image to the projector and then...

You see a selection box overlaying your image.
5. Use the arrow buttons on the remote control to surround the image area you want to use as the Users Logo and press Enter.
You see a prompt asking if you want to select this image area.
6. Select Yesand press Enter. (If you want to change the selected area, select No, pressEnter, and
repeat the last step.)
You see the Users Logo zoom factor menu.
7. Select a zoom percentage and press Enter.
You see a prompt asking if you want to save the image as the Users...

Related references
Projector Setup Settings - Extended Menu
Locking the Projectors Buttons You can lock the buttons on the projectors control panel to prevent anyone from using the projector. You
can lock all the buttons or all the buttons except the power button.
1. Press theMenubutton.
2. Select the Settingsmenu and press Enter.
3. Select the Control Panel Lock setting and pressEnter.
4. Select one of these lock types and press Enter:
• To lock all of the projectors buttons, select Full Lock.
• To lock...

Unlocking the Projectors Buttons
If the projectors buttons have been locked, hold the Enterbutton on the projectors control panel for
seven seconds to unlock them.
Parent topic: Locking the Projectors Buttons
Installing a Security Cable You can install two types of security cables on the projector to deter theft.
• Use the security slot on the projector to attach a Kensington Microsaver Security system, availablefrom Epson.
• Use the security cable attachment point on the projector to attach a wire cable...

2. Press the
Menubutton, select the Settingsmenu, and press Enter.
3. Select the Patternsetting and press Enter.
4. Select the User Patternsetting and press Enter.
You see a prompt asking if you want to use the displayed image as a User Pattern.
5. Select Yesand press Enter.
Note: It takes a few moments for the projector to save the image; do not use the projector, its remote
control, or any connected equipment until it is finished.
You see a completion message.
6. Press Escto exit the message screen....

Using the Interactive Features
Follow the instructions in these sections to use your projectors interactive features.
Interactive Modes
Using the Interactive Pens
Using BrightLink With a Computer
Using BrightLink Without a Computer
Interactive Modes The BrightLink interactive features turn any wall into an interactive whiteboard, either with or without a
computer. These interactive modes are available:
• In whiteboard mode, you can use one or both interactive pens to write on the projected whiteboard.
•...

1. Make sure the
Pen Modeoption in the Easy Interactive Function menu is set to PC Free
Interactive.
2. Hover near or tap the board or projected image with the interactive pen. Tap the left or right arrow icon,
3. Tap the whiteboard icon in the toolbar. You see the whiteboard screen, with the main toolbar on the side and the projection control toolbar
on the bottom of the screen:
4. To move the main toolbar to the other side of the screen, tap the arrow on the opposite side of the screen.
Note: You can...