Epson Aculaser C1700 User Manual

Chapter 7
Troubleshooting
Clearing Jams
Careful selection of appropriate print media and proper loading allow you to avoid most jams.
See also:
❏“About Print Media” on page 33
❏“Supported Print Media” on page 34
Note:
Before buying large quantities of any print media, it is recommended that you try a sample first.
Avoiding Jams
❏Use only recommended print media.
❏See “Loading Print Media in the Multipurpose Feeder (MPF)” on page 37 to load print media
properly.
❏Do not overload the print media sources....

See also:
❏“About Print Media” on page 33
❏“Supported Print Media” on page 34
Identifying the Location of Paper Jams
c
Caution:
Do not attempt to remove a paper jammed deeply inside the product, particularly a paper wrapped
around a Fusing Unit or a heat roller. Otherwise, it may cause injuries or burns. Switch off the
product promptly and contact your local Epson representative.
Important:
Do not attempt to clear any jams using tools or instruments. This may permanently damage the printer.
The following...

2 Transfer Belt
3 Levers
4 Rear Door
5Front Cover
6 Multipurpose feeder (MPF)
Clearing Paper Jams From the Front of the Printer
Note:
To resolve the error displayed on the operator panel, you must clear all print media from the print media
path.
1. Pull the paper cover out.
2. Remove any paper jammed from the front of the printer.
Epson AcuLaser C1700 Series     User’s Guide
Troubleshooting     73
 

3. Replace the paper cover in the printer.
Important:
Do not use excessive force on the paper cover. Doing so could damage it or the inside of the printer.
Clearing Paper Jams From the Back of the Printer
Important:
❏To prevent electric shock, always turn off the printer and disconnect the power cord from the
grounded outlet before performing maintenance.
❏To avoid burns, do not clear paper jams immediately after printing. The fusing unit becomes
extremely hot during use.
Note:
To resolve the error...

2. Lift up the levers.
3. Remove any paper jammed from the back of the printer.
4. Lower the levers to their original position.
Epson AcuLaser C1700 Series     User’s Guide
Troubleshooting     75
 

5. Close the rear door.
Clearing Paper Jams From the Center Output Tray
Important:
❏To prevent electric shock, always turn off the printer and disconnect the power cord from the
grounded outlet before performing maintenance.
❏To avoid burns, do not clear paper jams immediately after printing. The fusing unit becomes
extremely hot during use.
Note:
To resolve the error displayed on the operator panel, you must clear all print media from the print media
path.
1. Push the rear cover handle and open the rear...

2. Lift up the levers.
3. Remove any paper jammed from the back of the printer. If no paper is found in the paper path,
then remove any paper jammed out of the center output tray.
4. Lower the levers to their original position.
Epson AcuLaser C1700 Series     User’s Guide
Troubleshooting     77
 

5. Close the rear door.
Jam Problems
Misfeed jam
ProblemAction
Print media misfeeds occur. Ensure that the paper is properly inserted in the MPF.
Depending on the print media you use, take any of the following actions:
❏For thick paper, use the one that is 163 gsm or less.
❏For thin paper, use the one that is 60 gsm or more.
❏For the envelope, ensure that it is properly loaded in the MPF as instructed in
“Loading Envelope in the Multipurpose Feeder (MPF)” on page 43.
If the envelope is deformed, correct...

Multi-feed jam
ProblemAction
Print media multiple feeds occur. Ensure that the paper is inserted properly in the MPF.
If the print media is damp, use print media that is not damp.
Fan the print media.
Note:
If the problem continues even though you have taken suggested actions described above, contact the
Epson local representative office or an authorised dealer.
Basic Printer Problems
S o m e  p r i n t e r  p r o b l e m s  c a n  b e  e a s y  t o  r e s o l v e .  I f  a  p r o b l e m  o c c u r s  w...

Printing Problems
ProblemAction
Job did not print or incorrect characters
printed.Ensure that the 
 (Ready/Data) indicator is lit.
Ensure that print media is loaded in the printer.
Verify that you are using the correct print driver.
Ensure that you are using the correct USB cable and that it is securely connected to
the printer.
Verify that the correct print media size is selected.
If you are using a print spooler, verify that the spooler has not stalled.
Print media misfeeds or multiple feeds...