Epson 915 W Manual

Reset  menu
Resets  all  of  the  network  settings.
Submenu Function
Reset network
settings.To reset all of the Network settings, select Yes.
Info  Menu  (Display  Only)
Lets  you  check  the  status  of  the  image  signals  being  projected  and  the  status
of  the  projector.  Items  that  can  be  displayed  vary  depending  on  the  source
currently  being  projected.  Depending  on  the  model  used,  some  input
sources  are  not  supported.
s
 "Automatically  Detect  Input  Signals  and...

Submenu Function
StatusThis  is  information  about  errors  that  have  occurred  on  the
projector.
This  information  may  be  needed  if  service  is  required.
Serial  NumberDisplays  the  projector's  serial  number.
Event  IDDisplays  the  application  error  log.
s "About  Event  ID"  p.108
*The cumulative use time is displayed as "0H" for the first 10 hours. 10 hours
and  above  is  displayed  as  "10H",  "11H",  and  so  on.
Reset  Menu
Submenu Function
Reset...

Troubleshooting
This  chapter  explains  how  to  identify  problems  and  what  to  do  if  a  problem  is  found. 

If  a  problem  occurs  with  the  projector,  the  Help  screen  is  displayed  to  assist
you  by  pressing  the  Help  button.  You  can  solve  problems  by  answering  the
questions.a
Press  the  [Help]  button.
The  Help  screen  is  displayed.
Using the remote control Using the control panel
b
Select  a  menu  item.
Using the remote control Using the control panel
c
Confirm  the  selection.
Using the remote control Using the control panel
Questions  and  solutions  are  displayed  as  shown  on...

If  you  are  having  a  problem  with  the  projector,  first  check  the  projector's  indicators  and  refer  to  "Reading  the  Indicators"  below.
See  the  following  if  the  indicators  do  not  show  clearly  what  the  problem  might  be.s
 "When  the  Indicators  Provide  No  Help"  p.98
Reading  the  Indicators
The  projector  is  provided  with  the  following  three  indicators  that  indicate  the  operating  status  of  the  projector.
A
Power  indicator Indicates  the...

Refer  to  the  following  table  to  see  what  the  indicators mean  and  how  to  remedy  problems  that  they  indicate.
If  all  indicators  are  off,  check  that  the  power  cable  is  connected  correctly  and  that  the  power  is  being  supplied  normally.
Sometimes,  when  the  power  cable  is  unplugged,  the  
t indicator  remains  lit  for  a  short  period,  but  this  is  not  a  fault.
: Lit 
: Flashing 
: Off 
:  Varies  according  to  the  projector  status
Status Cause Remedy or...

Status Cause Remedy or Status
If it is not cracked: Reinstall the lamp and turn on the power.
If the error continues: Replace the lamp with a new one and then turn on the power.
If the error continues: Stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest
address provided in the Epson Projector Contact List.
s Epson Projector Contact List
If it is cracked: Contact your local dealer or the nearest address provided in the Epson Projector...

When  the  Indicators  Provide  No  Help
If  any  of  the  following  problems  occur  and  the  indicators  do  not  offer  a
solution,  refer  to  the  pages  given  for  each  problem.
Problems  Relating  to  Images•No images appear
Projection  does  not  start,  the  projection  area  is  completely  black,
or  the  projection  area  is  completely  blue.s p.99
•Moving images are not displayed
Moving  images  being  projected  from  a  computer  appear  black
and  nothing  is  projected.s p.100...

Problems  Relating  to  ImagesNo  images  appear
CheckRemedy
Did you press the [t] button? Press the [t] button to turn the power on.
Are the indicators switched off? The power cable is not connected correctly or power is not being supplied.
Connect the projector's power cable correctly.
s "From Installation to Projection" p.30
Check that your electrical outlet or power source is functioning correctly.
Is A/V Mute active? Press the [A/V Mute] button on the remote control to cancel A/V Mute.
s...

Moving  images  are  not  displayed  (only  the moving image portion turns black)
CheckRemedy
Is the computer's image signal being output to the LCD and the
monitor?
(Only when projecting images from a laptop computer or a
computer with a built-in LCD screen)Change the image signal from the computer to external output only. Check your computer's documentation, or contact
the computer's manufacturer.
Projection  stops  automatically
CheckRemedy
Is Sleep Mode set to On? Press the [t] button to...