Epson 1761 W Manual

Submenu Function
Encryption Key
1/Encryption Key
2/Encryption Key
3/Encryption Key
4You can enter the key used for WEP encryption. Enter the key in
single-byte characters following instructions from the network
administrator for the network in which the projector
participates. The type of character and the number that can be
entered differ according to the WEP Encryption and Format
settings.
128Bit - ASCII: Single-byte alphanumeric, 13 characters.
64Bit - ASCII: Single-byte alphanumeric, 5 characters....

s
 "Using  the  Mail  Notification  Function  to  Report  Problems"  p.125Submenu Function
Mail NotificationSet to On to send an email to the preset addresses when a problem
or warning occurs with a projector.
SMTP ServerYou can input the 
IP address
g for the SMTP server for the
projector.
You can enter a number from 0 to 255 in each field of the address.
However, the following IP addresses cannot be used.
127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from
0 to 255)
Port NumberYou...

Submenu Function
Trap IP Address
1/Trap IP Ad‐
dress 2You can register up to two IP addresses for the SNMP trap
notification destination. You can enter a number from 0 to 255 in
each field of the address. However, the following IP addresses
cannot be used. 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x
is a number from 0 to 255)
AMX Device Dis‐
cov er yWhen the projector is connected to a network, set this to On to
allow the projector to be detected by 
AMX
 Device
 Discovery
g.
Set this to Off if you...

Info  Menu  (Display  Only)
Lets  you  check  the  status  of  the  image  signals  being  projected  and  the  status
of  the  projector.  Items  that  can  be  displayed  vary  depending  on  the  source
currently  being  projected.  Depending  on  the  model  used,  some  input
sources  are  not  supported.s
 "Automatically  Detect  Input  Signals  and  Change  the  Projected  Image
(Source  Search)"  p.30Submenu Function
Lamp  HoursYou  can  display  the  cumulative  lamp  operating  time
*....

Submenu Function
Reset  AllYou  can  reset  all  items  in  the  Configuration  menu  to  their
default  settings.
The  following  items  are  not  reset  to  their  defaults:  Input
Signal, User's  Logo, all items for Network menus
*, Lamp
Hours, Language, Password, User  Button, and Multi-
screen.
Reset  Lamp
HoursClears  the  cumulative  lamp  hours  use  time.  Reset  when  you
replace  the  lamp.
* (EB-1776W/EB-1771W/EB-1761W  only)
List of Functions
95 

Troubleshooting
This  chapter  explains  how  to  identify  problems  and  what  to  do  if  a  problem  is  found. 

If  a  problem  occurs  with  the  projector,  the  Help  screen  is  displayed  to  assist
you  by  pressing  the  Help  button.  You  can  solve  problems  by  answering  the
questions.a
Press  the  [Help]  button.
The  Help  screen  is  displayed.
Using the remote control Using the control panel
b
Select  a  menu  item.
Using the remote control Using the control panel
c
Confirm  the  selection.
Using the remote control Using the control panel
Questions  and  solutions  are  displayed  as  shown  on...

If  you  are  having  a  problem  with  the  projector,  first  check  the  projector's  indicators  and  refer  to  "Reading  the  Indicators"  below.
See  the  following  if  the  indicators  do  not  show  clearly  what  the  problem  might  be.s
 "When  the  Indicators  Provide  No  Help"  p.101
Reading  the  Indicators
The  projector  is  provided  with  the  following  three  indicators  that  indicate  the  operating  status  of  the  projector.
A
Power  indicator Indicates...

Refer  to  the  following  table  to  see  what  the  indicators mean  and  how  to  remedy  problems  that  they  indicate.
If  all  indicators  are  off,  check  that  the  power  cord  is  connected  correctly  and  that  the  power  is  being  supplied  normally.
Sometimes,  when  the  power  cord  is  unplugged,  the  
t indicator remains lit for a short period, but this is not a fault.
: Lit 
: Flashing 
: Off 
:  Varies  according  to  the  projector  status
Status Cause Remedy or Status
Internal...

Status Cause Remedy or Status
If the lamp is not cracked: Reinstall the lamp and turn on the power.
If the error continues: Replace the lamp with a new one and then turn on the power.
If the error continues: Stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest
address provided in the Epson Projector Contact List.
s Epson Projector Contact List
If the lamp is cracked: Contact your local dealer or the nearest address provided in the Epson...