Epson 1761 W Manual

When  the  Indicators  Provide  No  Help
If  any  of  the  following  problems  occur  and  the  indicators  do  not  offer  a
solution,  refer  to  the  pages  given  for  each  problem.
Problems  Relating  to  Images•No images appear
Projection  does  not  start,  the  projection  area  is  completely  black,
or  the  projection  area  is  completely  blue.sp.102
•Moving images are not displayed
Moving  images  being  projected  from  a  computer  appear  black
and  nothing  is  projected.sp.103...

Problems  Relating  to  ImagesNo  images  appear
CheckRemedy
Did you press the [t] button? Press the [t] button to turn the power on.
Are the indicators switched off? The power cord is not connected correctly or power is not being supplied.
Connect the projector's power cord correctly.
s "From Installation to Projection" p.29
Check that your electrical outlet or power source is functioning correctly.
Is A/V Mute active? Press the [A/V Mute] button on the remote control to cancel A/V Mute.
s...

Moving  images  are  not  displayed
CheckRemedy
Is the computer's image signal being output to the LCD and the
monitor?
(Only when projecting images from a laptop computer or a
computer with a built-in LCD screen)Change the image signal from the computer to external output only. Check your computer's documentation, or contact
the computer's manufacturer.
Are the contents of the moving image you are trying to project
copyright protected?The projector may not be able to project copyright...

CheckRemedy
Is the correct port selected? Change the image by pressing the [Source Search] button on the remote control or the control panel.
s "Automatically Detect Input Signals and Change the Projected Image (Source Search)" p.30
Is the power for the computer or video source turned on? Turn the power on for the equipment.
Are the image signals being output to the projector?
(Only when projecting images from a laptop computer or a
computer with a built-in LCD screen)If the image signals are...

CheckRemedy
Has condensation formed on the lens? If the projector is suddenly taken from a cold environment to a warm environment, or if sudden ambient temperature
changes occur, condensation may form on the surface of the lens, and this may cause the images to appear fuzzy. Set the
projector up in the room about one hour before it is used. If condensation forms on the lens, turn the projector off and
wait for the condensation to disappear.
Interference  or  distortion  appear  in  images
CheckRemedy
Is...

The  image  is  truncated  (large)  or  small,  the  aspect is  not  suitable,  or  the  image  has  been  reversed
CheckRemedy
Is a wide panel computer image being projected?
(Only when projecting computer images)Change the setting according to the signal for the connected equipment.
s Signal - Resolution p.81
Is the image still being enlarged by E-Zoom? Press the [Esc] button on the remote control to cancel E-Zoom.
s "Enlarging Part of the Image (E-Zoom)" p.63
Is the image position adjusted...

CheckRemedy
Is the image brightness adjusted correctly? Adjust the Brightness setting from the Configuration menu.
s Image - Brightness p.80
Are the cables connected correctly? Check that all the cables required for projection are securely connected.
Check that no cables are disconnected and that there are no poor contacts in the cables.
s "Connecting Equipment" p.24
Is the 
contrast
g adjusted correctly? Adjust the Contrast setting from the Configuration menu.
s Image - Contrast p.80
Is the...

Problems  when  Projection  StartsThe  projector  does  not  turn  on
CheckRemedy
Did you press the [t] button? Press the [t] button to turn the power on.
Are the indicators switched off? The power cord is not connected correctly or power is not being supplied.
Disconnect and then reconnect the power cord.
s "From Installation to Projection" p.29
Check that your electrical outlet or power source is functioning correctly.
Do the indicators turn on and off when the power cord is touched? There is...

CheckRemedy
Is A/V Mute active? Press the [A/V Mute] button on the remote control to cancel A/V Mute.
s "Hiding the Image and Sound Temporarily (A/V Mute)" p.60
Is the audio cable's specification "No resistance"? When using a commercially available audio cable, make sure it is labeled "No resistance".
Is it connected with an HDMI cable? If no audio is output when connecting via an HDMI cable, set the connected equipment to PCM output.
Is Output audio from the projector...

Email  is  not  received  even  if  a  problem  occurs  in  the  projector  (EB-1776W/EB-1771W/EB-1761W  only)
CheckRemedy
Is Standby Mode set to Communication On? To use the Mail Notification function when the projector is in standby, set Communication On in Standby Mode from
the Configuration menu.
s Extended - Standby Mode p.84
Did a fatal abnormality occur and the projector come to a sudden
stop?If the abnormal state continues, contact your local dealer or the nearest address provided in the Epson...