Electrohome Vistagraphx 10k Roadie Users Manual

23(5$7,21
9LVWD*5$3+;#43.#8VHU*V#0DQXDO6067
controlling two protectors in the same area and want to work with one projector
at a time.
Note that if you change a protocol for either sensor to anything other than 
Off,
the protocol for the other sensor also changes. For example, setting the Front IR
Keypad option to 
Vista 
D also changes the Rear IR Keypad to 
Vista 
D. If you
want only one sensor to respond to a particular protocol —
Vista 
C, 
Vista 
D, or
Vista All — disable the other sensor by setting...

23(5$7,21
9LVWD*5$3+;#;3343.HU*V#0DQXDO6068
and Other Controls subsection if you need help. Changes made to the Preferences
menu will be saved when you exit the menu  (press 
([L W.)
)LJXUH#60481#3UHIHUHQFHV#0HQX
,PDJH#2ULHQWDWLRQ
Choose from Front, Rear, Inverted Front, Inverted Rear
according to your installation. If the setting is incorrect,
the image will be reversed and/or upside down. See 
2.6,
Operating Orientation for an illustrated explanation.
/DQJXDJH
Choose to display menu text in English,...

23(5$7,21
9LVWD*5$3+;#43.#8VHU*V#0DQXDO6069
LVSOD\#6OLGHEDUV
Enter a checkmark to superimpose a slidebar over the current image when an
adjustable parameter is selected directly. These slidebars include volume,
contrast, brightness, position, pixel tracking and phase, and others. If unchecked,
these slidebars (or any from 
)X QF codes) will be hidden during adjustment.
LVSOD\#(UURU#0HVVDJHV
Enter a checkmark to see on-screen messages indicating errors as they occur. See
3.9, Error Messages....

23(5$7,21
9LVWD*5$3+;#;3343.HU*V#0DQXDO606:
)LJXUH#60491#0DLQ#6WDWXV#0HQX#+VDPSOH,
)LJXUH#604:1#6WDWXV#6XE0PHQXV#+VDPSOH,
/DPS#&KDQJHG
When you install a new lamp assembly, select the Lamp Changed button on
the main Status menu to record the serial number of the new lamp. Using the
arrow keys to navigate, press 
(QWHU on the keypad to select each number or
character needed for the serial number (Figure 3-18). When you are done, select
the Accept button to record the new number — or press 
([L W to...

23(5$7,21
9LVWD*5$3+;#43.#8VHU*V#0DQXDO606;
Recording the serial number of the new lamp automatically resets the lamp timer
to 0. The timer will now begin logging each hour of use for the new lamp,
recording the current level in the main Status menu as “Lamp Hours”. Note that
the “Lamp Counter”, which shows the number of hours the lamp has been used
during the current rental period, does not automatically reset when a new lamp is
installed. See 4.4, Replacing the Lamp and Filter for complete instructions...

23(5$7,21
9LVWD*5$3+;#;3343.HU*V#0DQXDO606<
When working with multiple projectors, you may want to use the RS-232 ports
to chain the projectors together in a network that you control from either a
keypad or a computer/controller (see 2.9, Serial Port Connections). Or you may
prefer that each projector stands alone, in which case you will probably use a
single IR remote keypad. In either case, you can switch back and forth between
broadcasting to all projectors or controlling each projector individually....

23(5$7,21
9LVWD*5$3+;#43.#8VHU*V#0DQXDO6073
If you would like to be notified on-screen of error conditions, turn on this option
from within the Preferences menu (enter a checkmark in the Display Error
Messages box). Should a user error message ever appear on screen, press 
(QWHU
key to confirm the message and eliminate the message box. A system error must
be resolved in order to eliminate its message box.
NOTE: Error messages always appear at the rear LCD above the keypad.
,QYDOLG#8VHU#(QWU\
Any entry...

23(5$7,21
9LVWD*5$3+;#;3343.HU*V#0DQXDO6074
+DUG#5HVHW
If the projector does not respond to anything and appears to have inexplicably
failed, gently push a very small screwdriver or pen point into the Hard Reset
hole just to the right of the power LED. This reset will switch the projector off
(note that the power LED turns to yellow to indicate standby mode). Then
press 
3RZH U- to turn the projector back on. Previously unsaved settings will be
lost. 

6HFWLRQ#7
0DLQWHQDQFH
9LVWD*5$3+;#43.#8VHU*V#0DQXDO#704
VistaGRAPHX 10K is CSA approved and is designed for safe and reliable
operation. However, safe operation cannot be assured by design alone; installers,
maintainers, and users must maintain a safe operating environment for the
system. Please read through and understand the following warnings and
guidelines promoting safe usage of the projector.
:$51,1*
1HYHU#ORRN#GLUHFWO\#LQWR#WKH#SURMHFWRU#OHQV1
7KH#H[WUHPHO\#KLJK#EULJKWQHVV#RI#WKLV...