Electrohome Vistagraphx 10k Roadie Users Manual

23(5$7,21
9LVWD*5$3+;#43.#8VHU*V#0DQXDO607
67$786#/(6#0 Two LEDs (light emitting diodes) located to the right of the
Video Input Panel indicate Status (top) and Power (bottom). During normal
operation, the Power light is steady green and the Status light flashes green
each time a key is pressed or when the projector receives a serial command. Use
the following as a guide:
NOTE: A steady red power light accompanied by a coded pattern of red and
yellow flashes from the status light indicates an internal...

23(5$7,21
9LVWD*5$3+;#;3343.HU*V#0DQXDO608
will be green. If it moves to the 2II position, the projector will power off —
restart by first moving the breaker back to the 
2Q position, then try powering up
as usual. If the breaker continues to “trip” (moving to 
2II), the projector will
remain inoperable until the AC problem is corrected. Never use the circuit
breaker as an 
2Q22II switch.
;/5#&211(&7256#03-pin and 6-pin. For connecting the optional wired remote
keypad (3-pin) or optional Two-Way...

23(5$7,21
9LVWD*5$3+;#43.#8VHU*V#0DQXDO609
)LJXUH#6061#.H\SDG
This keypad is located at the rear of the projector. An LCD window above this
keypad provides feedback regarding current status and activities of the projector.
The IR Remote Keypad controls the projector by way of wireless
communications from a battery-powered infrared (IR) transmitter. Use the IR
remote keypad the same way you would use a remote keypad supplied with a TV
or VCR. When making key presses, point the keypad either toward the...

23(5$7,21
9LVWD*5$3+;#;3343.HU*V#0DQXDO60:
· the rear of the projector is inaccessible
· the lighting conditions are unsuitable for proper IR transmission
· you want to use a separate keypad for each projector in a group
Keep in mind the following guidelines:
4,
 Press keys one-at-a-time; there are no simultaneous key presses required.
5,
 For any key having an “*” (3RZH U-, for example), hold the key for a second or
two in order to toggle the function with a single key press. For other keys (or
to use a...

23(5$7,21
9LVWD*5$3+;#43.#8VHU*V#0DQXDO60;
,QSXW#7
Press 
,QSXW7 to select the input connected to ,1387#7 on the projector (S-Video).
This is the same as entering 
,QSXW   .
,QSXW
Press 
,QSXW   when you want to display from a specific source location, such
as a switcher connected serially to the projector’s switcher port. The first digit
represents the switcher number (usually 1-9, or “0” for one of the four inputs on
the projector), the second digit represents the slot number (1-9). For example:
,QSXW...

23(5$7,21
9LVWD*5$3+;#;3343.HU*V#0DQXDO60<
NOTE: ([L W does 
not save changes within text editing boxes or pull-down lists.
$UURZ#.H\V
Use the 
21 or 2)) keys to navigate within a menu or pull-down list or to
increase or decrease the value in the second (bottom) slidebar of a double
slidebar. Use 
 or  to change all other slidebar values — hold as desired
for continuous scrolling. Also use 
 or  to jump between “pages” in a
long pull-down list.
Use 
21 or 2)) in conjunction with certain toggle keys—those...

23(5$7,21
9LVWD*5$3+;#43.#8VHU*V#0DQXDO6043
will also introduce some level of noise in the image. Set below 50% to filter the
signal and remove noise from a noisy source.
&RQWUDVW
Press 
&RQW to increase or decrease the difference between light and dark areas of
your image. Use 
 and  until you reach the desired level of contrast,
making sure that the whites remain bright but not distorted or tinted.
%ULJKWQHVV
Press 
%ULJKW to increase or decrease the amount of perceived light in the image so
that black...

23(5$7,21
9LVWD*5$3+;#;3343.HU*V#0DQXDO6044
to shift the image up or down. Use  and  to zoom in and out (requires
zoom lens) or to shift the image slightly left or right. Note zoom range is 3-97.
6KXWWHU
Press and hold 
6KXWWHU- for a second or two to toggle the mechanical lens shutter
(dowser) closed or open with a single key press. Or quickly press and release
6KXWWHU- and follow immediately with 21 or 2)) if you want to guarantee the
correct toggle (useful if you are unsure of the present status)....

23(5$7,21
9LVWD*5$3+;#43.#8VHU*V#0DQXDO6045
NOTES: 1) With OSD on, you can still mute menus, error messages, slidebars,
etc. with the appropriate setting in the Preferences menu. 2) The status of the
26- key is displayed in the LCD window on the rear panel of the projector.
+HOS
Press 
+HOS for detailed information about any current menu and highlight. Press
+HOS again to exit. From presentation level, press +HOS to access the General Help
menu consisting of Using Help, Projector Setup, Keypad, Channel...

23(5$7,21
9LVWD*5$3+;#;3343.HU*V#0DQXDO6046
)LJXUH#6071#0DLQ#0HQX
On the keypad, either enter the number corresponding to the function menu you
wish to access, such as 
 for the Image Settings menu, or use the    keys to
highlight the desired icon and press (QWHU. The function menu you selected will
then appear.
Once you have a function menu displayed, navigate in a similar manner—enter a
menu option number for any numbered option, or use 
  to move the
highlight and press (QWHU. Items that are locked...