Eizo Coloredge Cg211 Users Manual

							
*: Settable/Adjustable 
Icons Functions FineContrast Modes
sRGB Custom CAL
Brightness** **-
Temperature**-*-
Gamma**-*-
Saturation-*-
Hue-*-
Gain-*-
6 colors-*-
Reset-*-
**These settings can be also adjusted on the FineContrast menu. 
*Allow the LCD monitor to stabilize for at least 30 minutes before making\
 image 
adjustments. (Allow the monitor to warm Up for at least 30 minutes befo\
re 
making adjustments.)
* Performing the  of the  menu returns the color settings of\
 the 
selected mode to the default settings.
* The values shown in percentages represent the current level within the s\
pecific 
adjustment. They are available only as a reference tool. (To create a u\
niform 
white or black acreen, the percentages for each will probably not be the\
 same.)
 
Adjustment Contents
Menu Function Descriptions Adjustable Range
Brightness
 To set the brightness of the 
screen 0 ~ 100%
Temperature To set the color temperature
4,000 ~ 10,000 K
in 500 K increments (including 9,300 
K). Default setting is 5,000K
 
						

							
*The values shown in the Kelvin are available only as a 
reference tool. 
*Adjusting the  turns the  adjustement 
OFF.
*Setting the temperature under 4,000 K or over 10,000 K 
invalidates the color temperature setting. (The color 
temperatures setting turns OFF.)
GammaTo set the gamma value1.8 ~ 2.6 (in 0.2 increments)
*If setting the gamma value, the using the monitor in the 
digital signal input is recommended.
If using the monitor in the analog input signal, set the gamma 
value from 1.8 to 2.2.
Saturation
 To change the saturation -100 ~ 100
Setting the minimum level (-100) 
turns the image to the monochrome.
*The  adjustment may cause undisplayable color 
tone.
Hue
 To change the flesh color, etc. -100 ~ 100
*The  adjustment may cause undisplayable color tone.
Gain
 To change each color (red, 
green and blue)  10 ~ 100%
By adjusting the red, green and blue 
color tones for each mode, custom 
colors can be defined. Display a 
white or gray background image and 
adjust the .
*The values shown in the percentage are available only as a 
reference tool.
*Setting the  invalidates the  
adjustment.  setting returns to the default setting. 
6 colors
 To adjust  and 
 in each color (Red, 
Yellow, Green, Cyan, Blue 
and Magenta) Hue: -100 ~ 100
Saturation: -100 ~ 100
Reset
 To return the color settings of 
the selected mode to the 
default settings Select the .
 
						

							
 
The  menu in the ScreenManager enables to set the power-sa\
ve setup.
 
*Do your part to conserve energy, turn off the monitor when you are finis\
hed 
using it. Disconnecting the monitor from the power supply is recommended\
 to 
save energy completely.
* Even if the monitor is in a power saving mode, USB compliant devices fun\
ction 
when they are connected to the monitors USB (both the Upstream and the\
 
Downstream ports). Therefore, power consumption of the monitor will cha\
nge 
according to the connected devices even if the monitor is in a power sav\
ing mode.
 
Analog Input
This monitor complies with the VESA DPMS standard.
To use the PCs Power Saving System (VESA DPMS).
[Procedure] (1) Set the PCs power saving settings.
(2) Select VESA DPMS in the  menu.
[Power saving system]
PC MonitorPower Indicator
Operation OperationBlue
Power saving STAND-BY
SUSPEND OFF Power saving
Yellow
[Power Resumption Procedure]
Operate the mouse or keyboard to return to a normal screen.
 
						

							
Digital Input
This monitor complies with the DVI DMPM.
[Procedure] (1) Set the PCs power saving settings.
(2) Select DVI DMPM from the  menu.
[Power saving system]
PC MonitorPower Indicator
Operation OperationBlue
Power saving/Off mode Power savingYellow
[Power Resumption Procedure]
Operate the mouse or keyboard to return to a normal screen .
Power on the PC to return a normal screen from the Off mode of the PC.
 
						

							
ActiveRotationII function allows you to change the display orientation o\
f the monitor 
with the panel rotation. Reder to Web site of EIZO NANAO CORPORATION for the latest information 
about supported graphics card (http://www.eizo.com/). 
 
* After changing the display orientation, it may take some time until the \
screen 
image is available. 
* · The ActiveRotationII function may not work correctly using with som\
e 
graphics card or OS.
* If you calibrate the monitor with the provided software, please set a pa\
nel in 
landscape before calibration. The portrait monitor cannot be calibrated \
with 
accuracy.
* When using the ActiveRotationII function with dual display, the screen i\
mage of 
either monitor can disapper. If so, redisplay the image by Display 
Properties (for Windows only). 
Operating Procedures
1.Turn the panel 90 degrees.
Since the default setting of  is set to Enable, the \
screen 
image responding to the panel orientation will be available.
*To disable the ActiveRotationII function, select Disable on  
menu in  menu. 
 
						

							
2.When the screen image is expanded or contracted, restart the PC.
The ActiveRotationII function may not work correctly using with some gra\
phics 
card or OS. When the screen image remains to be expanded or contracted a\
fter 
restarting the PC, please try to change the screen resolution setting of\
 your PC 
system.
* The ActiveRotationII Utility (for Windows) allows you to change the \
display 
oriantation easily. Please refer to the readme.txt in the EIZO LCD Utili\
ty Disk 
for the details. 
 
 
						

							
This monitor provides a hub which supports the USB standard. When connec\
ting to a 
USB compliant PC or another hub, the monitor functions as a hub which th\
e USB 
compliant peripherals can be easily connected.
 
Required System Environment
 
* PC equipped with USB ports or another USB hub connected to the USB 
compliant PC
* Windows 98/2000/XP//Mac OS 8.5.1 or later
* EIZO USB Cable (MD-C93, enclosed)
*The USB hub function may not work properly depending on the PC, OS or 
peripherals. Please consult the manufacturer of each device about the US\
B 
support.
* Using the USB Rev . 2.0 compatible PC or peripherals is recommended.
* When the main power of the monitor is not on, the peripherals connected \
to the 
downstream ports will not operate.
* Even if the monitor is in a power saving mode, the devices connected to \
the 
monitors USB ports (both the upstream and the downstream) will functi\
on.
* The followings are procedures for the Windows 98/Me/2000/XP and Mac OS.
Connecting to the HUB USB
1.Connect the monitor to the PC with the signal cable first, then turn on the PC.
 
						

							
2.Connect the upstream port of the monitor to the downstream port of the USB compliant PC or another hub by using the USB cable.
After connecting the USB cable, the USB function can be set up automatic\
ally.
 
3.After setting up, the monitors USB hub is available for connecting  USB compliant peripherals to the downstream ports of the monitor.
Connecting Examples
 
 
 
 
						

							
If a problem persists even after applying the suggested remedies, contac\
t an EIZO 
dealer.
l     No picture problems : See No.1 ~ No.2 
l     Imaging problems : See No.3 ~ No.14 
l     Other problems : See No.15 ~ No.18 
l     USB problems : See No.19 ~ No.20 
ProblemsPoints to check with possible solutions
1.No picture
Indicator status: Off [ ]
Check that the power cord is correctly 
connected. If the problem persists, turn off 
the monitor power for a few minutes, then 
turn it back on and try again.
Indicator status: Blue [ ]Check the Gain setting.
Indicator status: Yellow [ ]Switch the signal Input by pressing the input 
signal selection button on the front control 
panel.
[ ]
Try pressing a key on the keyboard, or 
clicking the mouse.
[ ] Try turning the PC on.
Indicator status: Slowly flashing 
Yellow [ ]
Try pressing the power button
2. Following messages 
appear. (Error messages 
shown below will remain 
on the screen for 40 
seconds.)
 These messages appear when the signal is not 
inputted correctly, even if the monitor 
functions properly.
[ ] When the image is displayed correctly after a 
short time, there is no problem with the 
monitor. (Some PCs do not output the signal 
soon after powering on.)
[ ] Check that the PC is turned ON.
[ ] Check that the signal cable is properly 
connected the PC or graphics board.
[ ] Switch the signal input by pressing the Input 
Signal Selection button on the front control 
panel.
 
						

							
Whenever an error signal 
message appears, the signal 
frequency will be displayed in 
red. (Example)[ ]Use the graphics boards utility software to 
change the frequency setting. (Refer to the 
manual of the graphics board.)
3. Display position is 
incorrect.[ ]Adjust the image position using the 
<
Position>.
[ ] If the problem persists, use the graphics 
boards utility software to change the display 
position if available.
4. Screen image is smaller 
or larger than the actual 
screen images.[ ]Adjust the resolution using the . 
5. Vertical bars of distortion 
appear.[ ]Decrease the vertical bars using the .
6. The characters and 
images have several 
vertical bars on their right 
side.[ ]Adjust the characters and images using the 
.