Eizo Coloredge Cg211 Users Manual

							
 
6.Change the input selection setting of the connector in the Input  Selection menu to ADC.
Press Enter button to complete the setting and the menu closes.
 
7.Switch on the PCs power.
The monitors power indicator will light up (blue).
If an image does not appear, refer to the 
7. TROUBLESHOOTING for advice.
Whenever finished, turn off the PC and the monitor.
* When turning on the monitor, the kind of the input signal (Signal1 or 2\
/Analog 
or Digital) is displayed for a few seconds on the right top corner of t\
he screen.
* Adjust brightness of the screen depending on the brightness of your envi\
ronment.
* Be sure to take adequate rests. A 10-minute rest period each hour is sug\
gested.
* When changing the signal connector except ADC, open the Input Selection \
menu 
again and change the setting to Standard.
* To  the settings in the  menu through ScreenManager, the \
settings of Input Selection will revert to the default setting.
Two PCs can be connected to the monitor through DVI-I connectors (SIGNAL 1 / 
SIGNAL 2) on the back of the monitor.
 
PC 1 PC 2
 
						

							
(EX.1)Digital ADC Signal Cable (FD-
C39 enclosed) 
+ADC-DVI display 
adapter 
(commercially 
available)
 
Signal Cable DD200 
[FD-C39](Optional)
 
DVI-D
Digital
(EX.2) Digital ADC Signal Cable (FD-
C39 enclosed) 
+ADC-DVI display 
adapter 
(commercially 
available)
 
Signal Cable (FD-
C16 enclosed) 
D-Sub 
mini 15 
pin
Analog
(EX.3) Digital ADC Signal Cable (FD-
C39 enclosed) 
+ADC-DVI display 
adapter 
(commercially 
available)
 
Signal Cable (FD-
C16 enclosed) + 
Adapter*
 
D-Sub 15 
pin
Analog
(EX.4) Digital DVI-D Signal Cable (FD-
C39 enclosed)
 
Signal Cable FD-C16 
enclosed) 
D-Sub 
mini 15 
pin
Analog
(EX.5) Digital DVI-D Signal Cable (FD-
C39 enclosed)
 
Signal Cable (FD-
C16 enclosed)+ 
Adapter*
 D-Sub 15 
pin
Analog
  *Macintosh Adapter (Optional)
 
						

							
Selecting the Active Input
The Input Signal Selection button on the control panel can be used to se\
lect either 
SIGNAL 1 or SIGNAL 2 as the active input at any time. Every time the but\
ton is 
pressed, the input changes. When switching the signal, the kind of the i\
nput signal 
(Signal 1 or 2/ Analog or Digital) is displayed for a few seconds on t\
he right top corner 
of the screen.
The Priority Input Signal
This function is used to select which PC will have priority to control t\
he monitor when 
utilizing two PCs. The monitor constantly checks the input signals and s\
witches 
automatically in accordance with the Input Priority setting (see tabl\
e below). Once a 
priority is set, whenever a change of signal is detected at the selected\
 input, the 
monitor will switch the input to that signal.
In this case of only one signal being present at either input, the monit\
or automatically 
detects and displays that signal.
 
Priority 
Settings Performance
1
(SIGNAL 1) If signals from both inputs are present, the monitor gives 
preference of Signal 1 in the following cases.
 
l     When the power of the monitor is turned ON. 
l     When the signal input to Signal 1 is changed even if active 
input was Signal 2.
 
2
(SIGNAL 2) If signals from both inputs are present, the monitor gives 
preference to Signal 2 in the following cases.
l     When the power of the monitor is turned ON. 
l     When the signal input to Signal 2 is changed even if active 
input was Signal 1.
 
 
						

							
ManualThe monitor will not detect signals automatically in this mode. 
Select the active input by pressing the input signal selection button 
on the monitors control panel.
 
*When 1 or 2 is selected, the power saving mode of the monitor activa\
tes only 
if both PCs are in power saving mode.
 
The Hood can reduce light reflection for on screen color consistency.
Setup Procedure
1.Attach the top hood to either the left or right hood before attaching to the monitor. The following figure shows the right hood.
2.Attach the hood to the monitor.
* Attaching one hood and tightening the screws should be completed before \
going 
on to the other hood. The following figure shows the example to begin wi\
th the 
left hood.
(1) Attach the left hood to the monitor from above and slide it from the sid\
e of the 
monitor until the hood is firmly positioned against the monitor. 
(2) Hold the left hood and tighten two screws on each side.
 
						

							
(3)Attach the right hood in the same way. 
3.  Slide the top hood to close.
The LCD monitor can be used with an arm by removing the tilt stand and a\
ttaching the 
arm or stand to the LCD monitor.
Using our optional arm or stand is recommended. (Ask your local dealer \
for 
information.)
 
 
						

							
*If you will use the arm or stand of other manufacturers, confirm the fol\
lowings to 
the manufacturers before selecting.
l     Hole spacing on the arm mounting: 100 mm x 100 mm (VESA 
compliant)
 
l     Supportable Weight: Total weight of the monitor (without stand) and 
attaching equipment such as a cable 
l     TÜV/GS approved arm or stand
* Please connect cables after attaching an arm stand.
 
Setup Procedure
1.Hold the center of the stand mounting cover and slide them rightward or leftward to remove the mounting cover.
2.Lay the LCD monitor down. Do not scratch the panel.
3.Remove the tilt stand by loosening the screws. (4 pcs of M4 x 15 mm )
 
						

							
4.Attach an arm stand to the LCD monitor securely.
4 Mounting Screws (enclosed) : M4 x 15(mm) 
 
 
						

							
ScreenManager allows you to adjust screen performance though the main me\
nu and 
select a FineContrast mode easily.
 
*Main Menu and FineContrast menu cannot be activated at the same time.
 
1.Entering the ScreenManager
Press the Enter button once to display the main menu of the ScreenManage\
r. 
 
2.Making Adjustments and Settings
(1) Select the desired sub menu icon using the Control buttons and press the\
 Enter 
button. The sub menu appears.
(2) Use the Control buttons to select the desired setting icon and press the\
 Enter 
button. The setting menu appears.
(3) Use the Control buttons to make all required adjustments and press the E\
nter 
button to save the settings.
 
 
						

							
3.Exiting the ScreenManager
(1)To return to the main menu, select the  icon or press the Down b\
utton 
twice, followed by the Enter button.
(2) To exit the ScreenManager, select  icon or press the Down button t\
wice, 
followed by the Enter button.
 
*Double clicking the Enter button at any time also exits the ScreenManage\
r menu.
 
FineContrast menu
Directly pressing the Left or Right button allows you to select the best\
 suited 
mode for screen display from 3 FineContrast modes; sRGB, Custom and CAL.\
 
To exit the menu, press the Enter button. 
 
The following table shows all the ScreenManagers adjustment and setting\
 menus.* 
indicates adjustments of analog input only and ** indicates digital in\
put only.
Main menu Sub menu Reference
Screen Clock *
4-1. Screen Adjustment 
Phase *
Position *
Resolution *
Range Adjustment *
Smoothing 
 
Signal Filter *
Color(Custom)
*1Brightness 4-3. Color Adjustment
Temperature
 
Gamma 
Saturation 
Hue 
Gain 
6 Colors 
 
						

							
Reset 
PowerManagerDVI DMPM **4-4. Power-save Setup 
VESA DPMS *
Off
 
Others Screen Size 4-2.Displaying a low resolutions
Border Intensity
 
Input Priority Select the priority input signal.
Off Timer
 Set the monitors off timer to on or 
off.
Beep
 Set the monitors beeper to on or 
off.
Menu 
Settings Menu Size
 Change the size of the menu.
Menu 
Position
 Adjust the menu position.
Menu Off 
Timer
 Set the menu displaying time.*2
Translucent Set the transparency of the 
background.
ActiveRotation II
 5.ActiveRotation II
Power Indicator
 
Make non-light for blue lighting 
when the screen is displayed (see 

Power Indicator setting). 
Reset
 
Return to the factory default 
settings.
Information Information
 
Review the ScreenManagers 
settings, model name, serial 
number and usage time.
*3
LanguageEnglish, German, French, 
Spanish, Italian, Swedish, 
Chinese•Simplified•, 
Chinese•Traditional• and 
Japanese
 
Select the ScreenManagers 
language.
*1 The adjustable functions on the  menu depend on the selected 
FineContrast mode. The above table shows the sub menus when the Custom\
 
mode is selected (see 
4-3. Color Adjustment).
*2 The displaying time of the FineContrast menu cannot be changed.
*3 Due to the inspection on the factory, the usage time may not 0 hour at\
 
shipping.