Eiki Projector Lc Xb29n User Manual

21
The preparation display will disappear 
after 30 seconds.
(See page 51 for Lamp control status.)
Lamp control status
Turning On the Projector
Connect the projector’s AC power cord into an AC
outlet. The POWER indicator lights red.
Press the POWER ON-OFF button on the top control or
on the remote control. The POWER indicator lights
green and the cooling fans start to operate. The
preparation display appears on the screen and the count
down starts. 
2
3
1
4After the countdown, the input source that was...

TO MAINTAIN THE LIFE OF THE LAMP, ONCE
YOU TURN THE PROJECTOR ON, WAIT AT
LEAST FIVE MINUTES BEFORE TURNING IT OFF.
“Power off?” disappears after 4 seconds.
Turning Off the Projector
Press the POWER ON-OFF button on the top control or
on the remote control, and “Power off?” appears on the
screen.
Press the POWER ON-OFF button again to turn off the
projector. The POWER indicator starts to blink red, and
the cooling fans keep running. (You can select the level
of fans’ quietness and speed. See “Fan” on...

23
Basic Operation
How to Operate the On-Screen Menu
The projector can be adjusted or set via the On-Screen
Menu. For each adjustment and setting procedure, refer to
the respective sections in this manual.
Use the Point 
7 8buttons to select a Menu icon. Use
the Point 
edbuttons to select an item in the selected
menu.
Press the SELECT button to show the item data. Use
the Point 
7 8buttons to adjust the values.
To close the On-Screen Menu, press the MENU
button again. Press the MENU button on the top...

Menu Bar
PC System Menu
Used to select
computer
system (p.30).
Image Adjust Menu
Used to adjust computer
image [Contrast/Brightness/
Color temp./White balance
(R/G/B)/Sharpness/Gamma]
(pp.35–36).
Setting Menu
Used to set the
projector’s operating
configurations (pp.45-
55).
Used to adjust
the volume or
mute the sound
(p.25).
Image Select Menu
Used to select an image
mode among Dynamic,
Standard, Real,
Blackboard(Green), and
Image 1–4 (p.34).
For computer source
AV System Menu
Used to select
system of...

25
Basic Operation
Rotate the Zoom Lever to zoom in and out.  
Rotate the Focus Ring to adjust the focus of the image.  
Zoom and Focus Adjustment Sound Adjustment
1
2
Press the MENU button to display the On-Screen
Menu. Use the Point 
7 8buttons to move the red
frame pointer to the Sound Menu icon.
Press the VOLUME+/– buttons on the top control or on the
remote control to adjust the volume. The volume dialog box
appears on the screen for a few seconds.
Press the MUTE button on the remote control to...

26
Basic Operation
If a projected picture still has keystone distortion after
pressing the AUTO SET UP button on the top control or the
AUTO SET button on the remote control, correct the image
manually as follows:
Press the KEYSTONE button on the remote control. The
Keystone dialog box appears. Use the Point 
edbuttons to
correct keystone distortion. The keystone adjustment can
be stored (see page 46).
Reduce the upper width 
with the Point 
ebutton. Reduce the lower width 
with the Point dbutton.  
•The...

27
Basic Operation
Press the FREEZE button on the remote control to freeze
the picture on the screen. To cancel the Freeze function,
press the FREEZE button again or press any other button.
FREEZE button
Press the AUTO PC button on the remote control to operate
the Auto PC Adj. function. The computer screen adjustment
can be done easily by pressing this button. See page 31 for
details.
AUTO PC button
Press the D.ZOOM buttons on the remote control to enter
to the Digital zoom +/– mode. See page 37 for...

ON - OFF
POWERINPUTWARNINGMENU
SELECT
28
Choose either Computer 1 (Analog) or Computer 2 by
pressing the INPUT button on the top control or press the
COMPUTER button on the remote control.
Before using these buttons, correct input source should be
selected through Menu operation as described below.
Press the MENU button to display the On-Screen
Menu. Use the Point 
7 8buttons to move the red
frame pointer to the Input Menu icon.1Input Menu
Use the Point edbuttons to move the red arrow
pointer to either...

ON - OFF
POWERINPUTWARNINGMENU
SELECT
29
Computer Input
Choose Computer 1(Digital) by pressing the INPUT button
on the top control or press the COMPUTER button on the
remote control.
Before using these buttons, correct input source should be
selected through Menu operation as described below.
Press the MENU button to display the On-Screen
Menu. Use the Point 
7 8buttons to move the red
frame pointer to the Input Menu icon.1Input Menu
Use the Point edbuttons to move the red arrow
pointer to Computer 1...

30
Computer Input
The Auto PC Adjustment
function operates to adjust 
the projector. 
PC System Menu
The PC System Menu icon 
Selected system is 
displayed.
Systems in this dialog box 
can be selected.
PC System Menu
Customized Mode (1–5) set in
the PC Adjust Menu (pp.32–33).
Computer System Selection
This projector automatically tunes to various types of computers based on VGA, SVGA, XGA, SXGA, WXGA, or
UXGA with its Multi-scan system and Auto PC Adjustment. If a computer is selected as a signal source,...