Eiki Projector Lc Sd15 User Manual

41
Setting
Lamp mode On start
When this function is “On,” the projector is automatically turned
on just by connecting the AC power cord to an AC outlet.
✔Note:
• Be sure to turn off the projector properly. (See “Turning Off the  Projector” on page
18). If the projector is turned off in an incorrect sequence, such as disconnecting the
AC power cord before completing the cool-down etc., the On start function does not
operate properly.
Power management
Time left until Lamp off
Press the SELECT button at...

42
Setting
Remote controlRemote control
Two different remote control codes are assigned to this projector;
the factory-set normal code (Code 1) and the secondary code
(Code 2). This switching function prevents interference with
different remote controls when several projectors or video
equipment nearby are used at one time.  
When operating the projector in “Code 2”, the code for both the
projector and remote control must be switched to “Code 2”.  
To change the code of the projector :
Set the remote...

43
The PIN code can be changed to your desired four-digit
number.
Select PIN code change with the Point 
dbutton, and press
the SELECT button. The New PIN code input dialog box will
appear.  
Select a number with the Point 
7 8buttons and fix the number
with the SELECT button. Repeat it to complete entering a four-
digit number. When the four-digit number is fixed, the pointer
automatically moves to Set. Then press the SELECT button.   To Change the PIN code Change the PIN code
The input numbers
are...

44
This function resets the lamp replacement counter. When
replacing the projection lamp, reset the lamp replacement counter
with this function. See page 49 for operation.Lamp counter reset
Factory default
This function restores all setting values except for the user logo,
PIN code lock, Logo PIN code lock and the lamp counter to the
factory default settings.
Select Factory default and this
box appears. Select [Yes], and
the next box appears. 
Factory default
Select [Yes] to
activate it.
This function...

45
The WARNING indicator shows the state of the function that protects the projector. Check the state of the WARNING
indicator and the POWER indicator to take proper maintenance. 
POWERLAMP
REPLACE
WARNING
-OFF
WARNING
blinking red
TOP CONTROL
Wa rn ing Indicator
The projector is shut down and the WARNING indicator is blinking red.
When the temperature inside the projector reaches a certain level,
the projector will be automatically shut down to protect the inside
of the projector. The POWER indicator is...

46
Maintenance and Cleaning
Air filters
Pull up and remove.
Turn off the projector, and unplug the AC power cord from
an AC outlet.
Turn the projector upside down and remove the air filters by
pulling the latches upward.
1
2
Air filters prevent dust from accumulating on the surface of the optical elements inside the projector. Should the air filters
become clogged with dust particles, it reduces the effectiveness of cooling fans and may result in a buildup of internal heat
and adversely affect the life...

47
Maintenance and Cleaning
Unplug the AC power cord before cleaning.
When the projector is not in use, replace the lens cover.
Unplug the AC power cord before cleaning.
Gently wipe the projector body with a dry soft cloth. When the
cabinet is heavily soiled, apply a small amount of mild detergent
and finish with a dry soft cloth. Avoid using an excessive amount
of cleaner. Abrasive cleaners, solvents, or other harsh chemicals
might scratch the surface of the cabinet.
When the projector is not in use,...

48
Maintenance and Cleaning
When the life of the projection lamp draws to an end, the LAMP
REPLACE indicator emits yellow light. If this indicator emits yellow light,
replace the lamp with a new one promptly.
Follow these steps to replace the lamp.
Lamp Lamp Cover
ORDER REPLACEMENT LAMP
Replacement lamp can be ordered through your dealer. When ordering a projection lamp, give the following
information to the dealer.
●
Model No. of your projector   : LC-SD15
●Replacement Lamp Type No. : POA-LMP78
(Service...

49
Maintenance & Cleaning
Maintenance and Cleaning
Be sure to reset the lamp replacement counter after the lamp is replaced. When the lamp replacement counter is reset, the
LAMP REPLACE indicator stops lighting.
Move the pointer to Lamp
counter reset and then press the
SELECT button. The message
“Lamp replacement counter
reset?” appears.
Turn on the projector and press the MENU button to display
the On-Screen Menu. Press the Point 
7 8buttons to move
the red frame pointer to the Setting Menu icon.
Press...

50
Troubleshooting
Before calling your dealer or service center for assistance, check the items below once again.
–Make sure you have properly connected the projector to peripheral equipment as described in Connecting to a Computer
and “Connecting to Video Equipment” on  pages 15 and 16. 
–Make sure all equipment is connected to an AC outlet and the power is turned on.
–When you operate the projector with a computer and it does not project an image, restart the computer.  
Appendix
Problem:–Solutions
No...