Eiki Projector Lc Sd15 User Manual

11
Part Names and Functions
Part Names and Functions
Point the remote control toward the projector (Infrared
Remote Receiver) when pressing any buttons. The
maximum operating range for the remote control is about
16.4’ (5m) and 60° in front of the projector.16.4’
(5 m)
Operating Range
y
e
i
u
!3
!4
t
r
!0
!2
!1
qPOWER ON-OFF button 
Turn the projector on or off. (p17, 18)
wVIDEO button
Select VIDEO input.  (p32)
eCOMPUTER button
Select COMPUTER input source. (p24, 32)
rMENU button
Open or close the...

12
Part Names and Functions
To insure safe operation, please observe the following precautions:
●Use (2) AA or LR6 type alkaline batteries.
●Always replace batteries in sets.
●Do not use a new battery with a used battery.
●Avoid contact with water or liquid.
●Do not expose the remote control to moisture or heat.
●Do not drop the remote control.
●If the battery has leaked on the remote control, carefully wipe the case clean and install new batteries.
●Risk of explosion if battery is replaced by an...

13
Installation
Projection angle can be adjusted up to 7.0 degrees with the
adjustable feet. 
Lift the front of the projector and pull the feet lock latches in
each side of the projector upward.1
Adjustable Feet
Feet Lock Latches
Release the feet lock latches to lock the adjustable feet and
rotate the adjustable feet to a proper height, and tilt. 2
To retract the adjustable feet, lift the front of the projector
and pull and undo the feet lock latches.
Keystone distortion of the projected image can be...

14
NOTE ON THE POWER CORD
AC power cord must meet the requirements of the country where you use the projector.
Confirm the AC plug type with the chart below and a proper AC power cord must be
used.
If the supplied AC power cord does not match your AC outlet, contact your sales dealer.
Installation
To power cord
connector on your
projector.
Projector sideAC outlet side
Ground
To the AC outlet.(120 V AC)
For Continental EuropeFor the U.S.A. and Canada
This projector uses nominal input voltages of 100-120 V...

15
Installation
Installation
Connecting to a Computer
MONITOR OUT
AUDIO  INVIDEOSERVICE PORT 
RESETCOMPUTER  / S-VIDEO      /COMPONENT IN
AUDIO  OUT
(VARIABLE)
Cables used for connection
• VGA Cable (Mini D-sub 15 pin)  
• Audio Cables (Mini Plug: stereo)
✽
(✽= Not supplied with this projector.)
External Audio Equipment
VGA cable  VGA cable 
Note:
When connecting the cables, the power cords of both the projector and
the external equipment should be disconnected from the AC outlet. 
✔Note:
•When...

16
MONITOR OUT
AUDIO  INVIDEOSERVICE PORT 
RESETCOMPUTER  / S-VIDEO      /COMPONENT IN
AUDIO  OUT
(VARIABLE)
Installation
Connecting to Video Equipment
Cables used for connection
• Scart-VGA Cable ✽
• S-VIDEO-VGA Cable ✽
• S-VIDEO Cable ✽
• Component-VGA Cable ✽
• Component Cable ✽
• Video Cable ✽
• Audio Cables (Mini Plug: stereo) ✽
(✽= Not supplied with this projector.)
Note:
When connecting the cables, the power cords of both the projector and
the external equipment should be disconnected from the AC...

17
Connect the projectors AC power cord into an AC outlet.
The POWER indicator blinks red for a moment and then
turns to steady red.
Press the POWER ON-OFF button on the top control or on
the remote control. The POWER indicator turns green
lighting and the cooling fans start to operate. The preparation
display appears on the screen and the countdown starts. 
2
3
1
16
The preparation display disappears after 20 seconds.
4After the countdown, the input source that was last selected
and the Lamp mode status...

18
Basic Operation
Press the POWER ON-OFF button on the top control or on
the remote control, and the message Power off? appears
on the screen.  
Press the POWER ON-OFF button again to turn off the
projector. The POWER indicator starts to blink red and it
continues blinking while the cooling fans are operating for
about 90 seconds. (About 120 seconds when the fan mode
is L2. See page 44.)   
1
2
TO MAINTAIN THE LIFE OF LAMP, ONCE YOU TURN
THE PROJECTOR ON, WAIT AT LEAST 5 MINUTES
BEFORE TURNING IT OFF....

19
Basic Operation
Rotate the Zoom Lever to zoom in and out.  
Rotate the Focus Ring to bring the image into focus.  
Zoom Lever
Focus Ring
Zoom and Focus Adjustment
Basic Operation 

20
Basic Operation
POWERLAMP
REPLACE WARNING
INPUT
MENU ON - OFF
SELECTVOLUME–VOLUME+
Top Control
Menu bar
Pointer
(red frame)Menu icon
Item data
Press the Point 7 8buttons
to adjust the value.
SELECT
button
Pointer (red frame)
Press the Point dbutton to
move the pointer.
Item
How to Operate the On-Screen Menu
MENU button
SELECT button POINT button
(outer ring)
On-Screen Menu
Quit 
Exit this menu.
The projector can be adjusted or set via the On-Screen Menu.
Refer to the following pages regarding each...