Eiki Projector Eip S200 User Manual

							
EN-20
Position the projector in a horizontal position; other positions can cause
heat build-up and damage to the projector.
Make sure the heat ventilation holes are not blocked.
Do not use the projector in a smoky environment. Smoke residue may
cause buildup on critical parts.
33.34(Min.)
55.56
83.35
138.9
277.8
(Max.)
259.62
129.8177.8951.93
31.1
1.2m
3.0m
5.0m
10.0m 2.0m
A
B
A:B=8.3:1.2
PROJECTION
DISTANCE (METER)
4:3 SCREEN SIZE-
DIAGONAL (INCH)
Wide
Tele
1.2
33.34 31.12.0
55.56
51.93 3.0
83.35
77.89 5.0
138.9
129.81 10.0
277.8
259.62
Adjusting Projection Image Size
Refer to the graphic and table below to determine the screen size and projection distance.
The values shown below are approximate and may vary from actual size. 
						

							
EN-21
Menu Operation
The projector has multilingual On Screen Display menus that allow you to make image
adjustments and change a variety of settings. 
						

							
EN-22
How to operate
1. Press Menu button to open the OSD menu.
2. When OSD is displayed, use  W / X  buttons to select any feature in the main menu.
After selecting the desired main menu feature, press  T button to enter sub-menu
for feature setting.
3. Adjust the settings with  W / X  buttons.
4. To return to the main menu, press  Menu button.
5. To exit OSD, press  Menu button. The OSD menu will close and the projector will
automatically save the new settings. 
						

							
EN-23
Image (Computer / Video Mode)
Contrast
The contrast controls the degree of difference between the lightest and darkest parts
of the picture. Adjusting the contrast changes the amount of black and white in the
image.
QPress W to decrease the contrast.QPress  X to increase the contrast.
Brightness
Adjusts brightness of the image.
QPress  W  to darken the image.QPress  X  to lighten the image.
Keystone
Adjusts image distortion caused by tilting the projector.
Aspect Ratio
Use this function to choose your desired image size.
Q1 :1: Keep the image with original width-height ratio and maximize the image t\
o fit native horizontal or vertical pixels.
Q16:9:The input source will be scaled to fit the width of the screen.Q4:3:The input source will be scaled to fit the projection screen.
Blank Screen
Blanks the screen temporarily, and selects the screen color when this function is active.
QBlack / Blue / Gray / Red / Green / Yellow / Cyan / Magenta / White
Gamma
Selects Gamma mode.
QRGB: Computer text modeQPhotographic: Computer photo modeQVideo: Common video modeQFilm: Dark video image mode
White Peaking
The white peaking control adjusts the white peaking level of the DMD chip. 0 stands for
minimal segment, and 10 stands for maximum segment. If you prefer a stro\
nger image,
adjust towards the maximum setting. For a smooth and more natural image,\
 adjust
towards the minimum setting.
Color Temperature
Adjusts color temperature. At higher temperature, the screen looks colder; at lower
temperature, the screen looks warmer. If you select “User”, “Re\
d”, “Green” and “Blue”
can be adjusted. 
						

							
EN-24
Red
Manually adjusts red.
Green
Manually adjusts green.
Blue
Manually adjusts blue.
Video (Video Mode)
Saturation
Adjusts a video image from black and white to fully saturated color.
QPress W to decrease the amount of color in the image.QPress  X to increase the amount of color in the image.
Tint
Adjusts the color balance of red and green.
QPress  W to increase the amount of green in the image.QPress  X to increase the amount of red in the image.
Sharpness
Adjusts the sharpness of the image.
QPress  W to decrease the image.
QPress  X to increase the image.
Display (Computer Mode)
Phase
“Phase” synchronizes the signal timing of the display with that of the graphic card. If
you experience an unstable or flickering image, use the phase function to correct it.
Tracking
“Tracking” changes the display data frequency to match the frequency of your computer
graphic card. If you experience a vertical flickering bar, use the tracking function to
make an adjustment.
H.Position (Horizontal Position)
QPress  W to move the image left.QPress  X to move the image right.
V.Position (Vertical Position)
QPress  W to move the image down.QPress  X to move the image up. 
						

							
EN-25
Audio (Computer / Video Mode)
VolumeQPress W to decrease the volume.QPress  X to increase the volume.
Mute
QChoose “ON” to turn mute on.QChoose “OFF” to turn mute off.
Language (Computer / Video Mode)
Choose the multilingual OSD menu. Use  S / T  to select your preferred language. Press
“ W  / X  / Enter ” to finalize the selection.
Advanced (Computer / Video Mode)
Auto Source Select
Automatically scans the input source. Press “ W / X  / Enter ” to confirm or cancel the
selection.
Rear
The image is reversed horizontally. Press “ W / X  / Enter ” to confirm or cancel the
selection.
Ceiling
The image is inverted vertically. Press “ W / X  / Enter ” to confirm or cancel the selection.
ECO/Hi_Alt Mode
Use this function to dim the projector lamp light output which will lower power
consumption and increase lamp life, or/and turning on High Altitude mode operates the
fans at full speed continuously to allow for proper high altitude coolin\
g of the projector.
Lamp Hours
Displays Hour the lamp’s elapsed operating time (in hours).
Color Space
Manually selects signal type.
QRGBQYCbCrQYPbPr
Auto Shutdown
Uses this function to automatically turn off the lamp if the projector does not detect an
input signal for specified time period (30 minutes).
OSD  Timeout
Duration OSD menu stays active (at idle state by second).
Menu Position
Choose the menu position on the display screen.
Factory Reset
Press “ W / X  / Enter ” to enter its menu. Use  S / T  to choose “
”  and press “ W / X
/  Enter ” to return the display parameters on all menus to the factory default settings. 
						

							
EN-26
Maintenance
The projector needs proper maintenance. You should keep the lens clean as dust, dirt
or spots will project on the screen and diminish image quality. If any o\
ther parts need
replacing, contact your dealer or qualified service personnel. When cleaning any part
of the projector, always switch off and unplug the projector first.
Warning:
Never open any of the covers on the projector. Dangerous electrical voltages inside
the projector can cause severe injury. Do not attempt to service this product yourself.
Refer all servicing to qualified service personnel.
Cleaning the Lens
Gently wipe the lens with lens cleaning paper. Do not touch the lens with your hands
or fingers.
Cleaning the Projector Housing
Gently wipe with a soft cloth. If dirt and stains are not easily removed, use a soft cloth
damped with water, or water and neutral detergent, and wipe dry with a soft, dry cloth.
Turn off the projector and remove the AC power cord from the power
outlet before beginning maintenance work.
Make sure the lens is cool before cleaning.
Do not use detergents or chemicals other than those noted above. Do
not use benzene or thinners.
Do not use chemical sprays.
Use a soft cloth or lens paper only. 
						

							
EN-27
Replacing the Lamp
Projector lamps have a finite life. Replace the lamp when:
JThe image becomes darker and hues become weaker after a lamp has been for a
long period of time.
JThe projector lamp LED indicator turns into amber. Refer to section titled “LED
Indicator Messages”   (p.30) for further details.
JThe lamp becomes high temperature after turning off the projector with t\
he
power button. If you touch the lamp, you may scald your finger. When you\
replace the lamp, wait for at least 45 minutes for the lamp to cool down\
.
JDo not touch the lamp glass at any time. The lamp may explode due to
improper handling, including the touching of the lamp glass.
JLamp lifetime may differ from lamp to lamp and according to the
environment of use. There is no guarantee of the same lifetime for each
lamp. Some lamps may fail or terminate their lifetime in a shorter perio\
d
of time than other similar lamps.
JA lamp may explode as a result of vibration, shock or degradation as a
result of hours of use as its lifetime draws to an end. Risk of explosion
may differ according to the environment or conditions in which the
projector and lamp are being used.
JFaster on-off-cycles will damage the lamp and reduce lamp life. Wait at
least for 5 minutes to turn off the projector after powering on.
JDo not operate the lamp in proximity to paper, cloth, or other combustib\
le
material nor cover it with such materials. Otherwise it could cause a fi\
re.
JDo not operate the lamp in an atmosphere containing an inflammable
substance, such as thinner. Otherwise it could cause a fire or explosion.
JThoroughly ventilate the area or the room when operating the lamp in
an oxygen atmosphere (in the air). If ozone is inhaled, it could cause
headaches, nausea, dizziness, etc.
JThe inorganic mercury is involved in the lamp. If the lamp bursts, the
mercury inside the lamp will go out of the projector. Leave the area
immediately if the lamp shatters while being operated and ventilate the
area for at least 30 minutes in order to avoid the inhalation of mercury\
fumes. Otherwise it could be harmful to user’s health. 
						

							
EN-28
1. Turn off the projector and unplug the AC powercord.
Allow the projector to cool for at least 45
minutes.
2. Place a protective sheet (cloth) beneath the projector. Turn the projector over so you can
access the lamp cover.
3. Loosen the screws on the lamp cover and open it.
4. Loosen the screws on the bottom of the lamp assembly.
5. Grasp the lamp handle and pull the lamp assembly
directly out of the projector.
6. Replace with the new lamp.
7. Tighten the screws on the bottom of lamp assembly.
8. Tighten the screws on the lamp cover.
JDispose of the used lamp according to local regulations.
JEnsure that screws are tightened properly. Screws not tightened fully
may result in injury or accidents.
JSince the lamp is made of glass, do not drop the unit and do not scratch
the glass.
JDo not reuse the old lamp. This could cause the lamp to explode.
JBe sure to turn off the projector and unplug the AC power cord before
replacing the lamp.
JDo not use the projector with the lamp cover removed.
ORDER  REPLACEMENT  LAMP
Replacement lamp can be ordered through your dealer. When ordering a projection
lamp, give the following information to the dealer. Model No. of your projector :   EIP-S200
Replacement Lamp No. : P8384-1014 
						

							
EN-29
Specifications
Display Type Single 0.55 DLP panel
Resolution (Pixels)800 x 600
Uniformity 85%
Lens Manual Zoom (1.07x)
F=2.4 6mm
f=19 .91- 21.36mm
Contrast Ratio2000 : 1
Aspect Ratio 4:3 (Default) , 16:9
Screen Size 31.1 - 277.8
Throw Distance1.2m - 10m
Lamp 200W
Projection Type Front, Rear, Ceiling
Video CompatibilityNTSC4.43
PAL-60, PAL-M,N,(B,D,G,H,I )
SECAM
Input Source D-Sub 15 pin, S-Video, Composite Video, Stereo Phone
Jack, RS232, USB
Scanning Frequency Horizontal Frequency 31 - 79 KHz
Vertical Frequency 50 - 85 Hz
Digital Keystone Correction Vertical + / - 15°
Integrated Speaker 1 x 2W
Acoustic Noise36dBA
Storage Temperature -20 - + 60°C
Operation Temperature +5 - + 35°C
Operation Humidity 35%  -  85% maximum (No Condensation)
Power Requirement AC 100  – 240V, 50 / 60 Hz
Power Consumption 250W Standby mode: less than 5W
Dimension (W x D x H) 255.5 x 223 x 101.5mm
Weight3.0kg (6.6lb)
Note: Design and Specifications are subject to change without prior notice.