Eiki Projector Eip S200 User Manual

							
MULTIMEDIA PROJECTOR
MODEL EIP-S200
OWNER’S MANUAL 
						

							
EN-1
Federal Communication Commission Notice
Note : This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can ra\
diate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there i\
s no
guarantee that interference will not occur in a particular installation.\
 If this equipment
does cause harmful interference to radio or television reception, which \
can be
determined by turning the equipment off and on, the user is encouraged t\
o try to
correct the interference by one or more of the following measures :
„Reorient or relocate the receiving antenna.
„ Increase the separation between the equipment and receiver.
„ Connect the equipment into an outlet on a circuit different from that to\
 which the
receiver is connected.
„ Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15
of FCC Rules.
Do not make any changes or modifications to the equipment unless otherwi\
se specified
in the instructions. If such changes or modifications should be made, yo\
u could be
required to stop operation of the equipment.
Model Number : EIP-S200
Trade Name : EIKI
Responsible party : EIKI International, Inc.
Address : 30251 Esperanza Rancho Santa Margarita CA 92688-2132
Telephone No. : 800-242-3454 (949-457-0200) 
						

							
EN-2
Safety Instructions
Read all of these instructions before you operate your projector and sav\
e for future
reference.
CAUTION : T O  REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK).  NO USER-SERVICEABLE PARTS
INSIDE EXCEPT LAMP REPLACEMENT.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
THIS SYMBOL INDICATES THAT DANGEROUS
VOLTAGE CONSTITUTING A RISK OF ELECTRIC
SHOCK IS PRESENT WITHIN THIS UNIT.
THIS SYMBOL INDICATES THAT THERE ARE
IMPORTANT OPERATING AND MAINTENANCE
INSTRUCTIONS IN THE OWNERS MANUAL WITH
THIS UNIT.
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
0.7(20cm)
1.5(50cm) 3(1m)
1.5(50cm)
SIDE and TOPREAR
An appliance and cart combination should
be moved with care.  Quick stops,
excessive force, and uneven surfaces
may cause the appliance and cart
combination to overturn.
Allowing the proper amount of space on the top, sides, and rear of the projector
cabinet is critical for proper air circulation and cooling of the unit. \
The dimension
shown here indicate the minimum space required. If the projector is to be built into
a compartment or similarly enclosed, these minimum distances must be mai\
ntained. 
						

							
EN-3
1. Check that the operating voltage of your unit is identical with the volt\
age of yourlocal power supply.
2. Should any liquid or solid object fall into the cabinet, unplug the unit\
 and have it checked by the qualified personnel before operating it further.
3. Do not attempt to service this product yourself, as opening or removing covers may damage the components inside and will void your warranty.
4.  Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious damage to the product.
5. Unplug the unit from the wall socket if it is not to be used for several days. To disconnect the cord, pull it out by  the plug. Never pull the cord itself.
6. The wall socket should be near the unit and easily accessible.
7. Do not place the projector where the cord can be stepped on as this may result in fraying or damage to the lead or the plug. Be alert to tripping hazards.
8. Never look into the projector lens when the lamp is switched on as the bright light can damage your eyes. Never let children look into the lens when it is on.
9.  Do not place your hand or objects near the ventilation holes. The air coming out is hot.
10. Never open any covers on the projector except the lamp cover. Dangerous electrical voltages inside the projector can cause severe injury. Except as specifically directed
in this User’s Manual, do not attempt to service this product yoursel\
f. Refer all
servicing to qualified service personnel.
11. Unplug the projector from the wall socket before cleaning. Use a damp cloth for cleaning the projector housing. Do not use liquid or aerosol cleaners.
12. Keep the plastic packing materials (from the projector, accessories and optional parts) out of the reach of children as these bags may result in death by suffocation.
Be particularly careful around the small children.
13. For ventilation reasons, the fan continues to operate after the projector has been powered off. Please do not unplug the power cord until the fan stops. 
						

							
EN-4
14. The projector is equipped with ventilation holes (intake) and ventilat\
ion holes(exhaust). Do not block or place anything near these slots, or internal heat build-up
may occur, causing picture degradation or damage to the projector.
15. When you replace the projector lamp, never touch the new bulb with your bare hands. The invisible residue left by the oil on your hands may shorten t\
he bulb life.
Use lint-free gloves or finger cots are recommended.
16. The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
17. Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock. 
						

							
EN-5
Ground
Notes on AC Power Cord
AC Power Cord must meet requirement of country where you use a projector\
. Confirm
an AC plug type with graphics below and proper AC Power Cord must be used. If
supplied AC Power Cord does not match your AC outlet, contact your sales dealer. This
projector is equipped with a grounding type AC line plug. Make sure that your outlet fits
the plug. Do not defeat the safety purpose of this grounding type plug. We highly
recommend using a video source device also equipped with a grounding type AC line
plug to prevent from signal interference due to voltage fluctuation. 
						

							
EN-6
CONTENTS
CONTENTS CONTENTS
CONTENTS
CONTENTS
Introduction ........................................................................\
................................... 7
Projector Features ........................................................................\
..................... 7
Package Contents ........................................................................\
...................... 8
Projector Overview ........................................................................\
................... 9
Using the Product ........................................................................\
....................... 11
Control Panel ........................................................................\
........................... 11
Terminals ........................................................................\
................................. 12
Remote Control ........................................................................\
........................ 13
Remote Control Operation ........................................................................\
........ 15
Installation ........................................................................\
.................................... 16
Connecting the Projector ........................................................................\
.......... 16
Powering On/Off the  Projector........................................................................\
 17
Adjusting the Projected Image ........................................................................\
.. 18
Menu Operation ........................................................................\
........................... 21
Image (Computer / Video Mode) ....................................................................... 23
Video (Video Mode) ........................................................................\
................. 24
Display (Computer Mode) ........................................................................\
......... 24
Language (Computer / Video Mode) ................................................................ 25
Advanced (Computer / Video  Mode)................................................................ 25
Audio (Computer / Video  Mode)....................................................................... 25
Maintenance ........................................................................\
................................ 26
Cleaning the Lens ........................................................................\
.................... 26
Cleaning the Projector Housing ........................................................................\
 26
Replacing the Lamp ........................................................................\
.................. 27
Specifications ........................................................................\
.............................. 29
Appendix ........................................................................\
...................................... 30
LED Indicator Messages ........................................................................\
.......... 30
Compatibility Modes ........................................................................\
................. 31
Troubleshooting ........................................................................\
....................... 32
Configurations of  Terminals........................................................................\
..... 33 
						

							
EN-7
* means compressed.
Introduction
Projector Features
The projector integrates high-performance optical engine projection and \
a user-friendly
design to deliver high reliability and ease of use.
The projector offers the following features:
Single chip 0.55 Texas Instruments DLP® technology
SVGA (800 x 600 pixels) true resolution
1.07x manual zoom lens
Auto image re-sizing (Auto-Sync.) to 800 x 600 full screen with scalin\
g compression
compatibility for VGA, SVGA, XGA* and SXGA*
Compatibility with Macintosh® computers
Compatibility with NTSC, PAL, SECAM, and HDTV
Multi-function remote control
D-Sub 15-pin terminal for analog video connectivity
User-friendly, multi-language on-screen display (OSD)
Advanced electronic keystone correction 
						

							
EN-8
Package Contents
When you unpack the projector, make sure you have all these components:
Save the original shipping carton and packing material; they will come
in handy if you ever to ship your unit. For maximum protection, repack
your unit as it was originally packed at the factory.
Projector with Lens Cap AC Power CordVGA Cable (D-Sub to D-Sub)
Composite Video Cable
Remote Control (IR)
with Lithium battery
Quick Start Guide
Audio CableS-Video Cable
Owner’s ManualProjector Carrying Case 
						

							
EN-9
Projector Over view
Front View
 1Ventilation holes
 2Projection lens
 3Front IR remote control sensor
 4Lens cap
 5Elevator foot
 978
1123456
 6Elevator button
 7Zoom ring
 8Focus ring
 9Control panel