Eiki Projector Eip S200 User Manual

							
EN-10
Rear View
 1Rear IR remote control sensor
 2Ventilation holes
 3Terminals
 4Elevator button
 5 Elevator foot
 6 Speaker
 7 AC power socket
 8 Kensington lock
1232
65478
1
2
2
2
This projector can be used with a ceiling mount for support. The ceiling
mount is not included in the package.
Bottom View
 1 Lamp cover
 2 Ceiling mount 
						

							
EN-11
Using the Product
Control Panel
LED
 1Lamp LED indicator
Refer to “LED Indicator Messages”. (p.30)
 2 Power LED indicator
Refer to “LED Indicator Messages”. (p.30)
Button Function
  3 Power
Refer to “Powering On/Off the Projector”.
  4 Keystone 
S
S S
S
S /
T
T T
T
T
Adjusts image distortion caused by tilting the projector.
  5 Auto 
X
X X
X
X
Automatically adjusts frequency, total dots. This function is available \
for computer
mode only.
 6 Menu
Displays or exits the on-screen display menus.
  7 Source 
W
W W
W
W
Manually selects an input source.
  8 Four directional buttons
Use four directional buttons to select items or make adjustments to your\
 selection.
1
8
7
2
3
4
5
6 
						

							
EN-12
Ter minals
 1SERIAL
When operating the projector via a computer, connect this to the control\
ling
computer’s RS-232C port.
 2  USB(COMPUTER)
This connector is for firmware update.
 3 COMPUTER  IN
Connects image input signal  (analog) to this jack.
 4 S-VIDEO
Connects S-V ideo output from video equipment to this jack.
 5 VIDEO
Connects  composite video output from video equipment to this jack.
 6 AUDIO IN
Connects an audio  output from video equipment to this jack.
235641 
						

							
EN-13
Remote Control
 1Power
Refer to “Powering On/Off the
Projector”. (p. 17)
 2 Four directional buttons
Use four directional buttons to select
items or make adjustments to your
selection. (p. 22)
  3 Menu
Displays or exits the on-screen display
menus. (p. 22)
  4 Enter
To select the desired setting. (p. 25)
  5 Keystone  c /d
Adjusts image distortion caused by tilting
the projector. (p. 11, 23)
 6 Volume  c /d
Press the Volume  c button to increase
the volume
press the Volume  d button
to reduce the volume. (p. 25)
 7 Source
Manually selects an input source. (p. 11,
17, 25)
 8 Mute
Cuts off the sound temporarily. Press
again to cancel the Mute function. (p. 25)
 9 Blank
Cuts off the screen temporarily. Press
again to cancel the Blank function.
(p. 23, 32)
10 4:3/16:9
Press the 4:3/16:9 to switch the image
aspect ratio from 4:3 to 16:9.
11 Auto
Automatically adjusts frequency, total
dots. This function is available for
computer mode only. (p. 11, 24, 32) 
						

							
EN-14
For the first time use:
Remove the transparent insulation tape by pulling it
before use.
For batter y change:
1. Push the catch to the right and remove thebattery holder.
2. Remove the old Lithium coin cell and install new one (CR2025). Ensure that the side with the
mark “+” is up.
3. Push the battery holder back into the remote control until you feel a click.
Catch
Battery holder
Keep the battery out of the reach of children. There is a danger of death
by accidentally swallowing the battery.
Do not recharge the used battery or expose the battery to fire or water.\
Do not dispose of the used battery along with household waste. Dispose
of used batteries according to local regulations.
Danger of explosion may happen if a battery is incorrectly replaced.
Replace only with the same type recommended by the manufacturer.
Notes on Lithium Batter y
(CALIFORNIA USA ONLY)
This product uses a Lithium Battery which contains
Perchlorate Material - special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate 
						

							
EN-15
Remote Control Operation
Point the remote control at the infrared remote sensor and press a butto\
n.
  Operating the projector from the front
  Operating the projector from the rear
The remote control may not operate when there is sunlight or other
strong light such as a fluorescent lamp shining on the remote sensor.
Operate the remote control from a position where the remote sensor is
visible.
Do not drop the remote control or jolt it.
Keep the remote control out of locations with excessively high
temperature or humidity.
Do not get water on the remote control or place wet objects on it.
Do not disassemble the remote control.
1015
7m5m
5m
1015
7m5m
5m 
						

							
EN-16
Desktop type
Laptop type
23
75
1
46
When connecting cable, power cords of both a projector and external
equipment should be disconnected from AC outlet.
The figure above is a sample connection. This does not mean that all of
these devices can or must be connected simultaneously.
The cables that come with the projector may differ from the above
illustration. The included cables are based on actual shipment delivery.
Installation
Connecting the Projector
 
1 RS232 Cable 5Composite Video Cable
  2 USB Cable 6S-Video Cable
  3 VGA Cable (D-Sub to D-Sub) 7VGA (D-Sub) to HDTV (RCA) Cable
  4 Audio Cable 
						

							
EN-17
Powering On/Off the Projector
Powering on the projector:
1. Remove the projector lens cap.
2. Complete the AC power cord and peripheral signal cable(s) connections.
3. The Power LED blinks Green in standby mode.
4. Press 
 button on the control panel or remote control to turn on the projector.\
 The
Power LED lights on Amber and Lamp LED lights on Green when the lamp is on.
5. Turn on your source (computer, notebook, DVD, etc.). The projector automatically detects your source.
JWhen searching message appears on the screen, ensure that the appropriate
signal cable(s) are securely connected.
JThe signal message will appear on the screen when the source is detected.
JIf you are connecting multiple sources to the projector simultaneously, \
press
Source  button.
Warning:
JRemove the lens cap first before powering on.
JNever look into the lens when the lamp is on. This can damage your eyes. It is
especially important that children are not allowed to look into the lens\
.
Powering Off the Projector:
1. Press  button on the control panel or remote control. “Power Off? Press Pow\
er
again” message will appear on the screen.
2. Press 
 button again to turn off the projector.
3. The cooling fans continue to operate for cooling cycle and the Power LED\
 lights on Amber and Lamp LED blinks Green. When the Power LED begins flashing (Lamp LED
lights off), the projector has entered standby mode.
If you wish to turn the projector back on, you must wait until the projector has
completed the cooling cycle and has entered standby mode.
Once in standby mode, simply press 
 button to restart the projector.
4. Disconnect the power cord from the electrical outlet and the projector.
5. Do not turn on the projector immediately following a power off procedure\
.
Please wait until the fan motor and the Lamp LED turn off before removing
the AC power cord from the projector. 
						

							
EN-18
Adjusting the Projected Image
Adjusting the Projector Height
The projector is equipped with an elevator foot to adjust the image heig\
ht.
To raise the image:
1. Press the elevator button.
2. Raise the image to the desired height angle, then release the button to lock theelevator foot into position.
To lower the image:
1. Press the elevator button.
2. Lower the image, then release the button to lock the elevator foot into position.
To avoid damaging the projector, make sure that the elevator foot is
fully retracted before placing the projector in its carrying case.
Elevator foot Elevator button 
						

							
EN-19
Adjusting the Projector Zoom and Focus
1. Focus the image by rotating the focus ring. A still image is recommended for focusing.
2. Adjust the image by rotating the zoom ring. Rotate to the right to reduc\
e the image.Rotate to the left to enlarge the image.
Focus ringZoom ring