Eiki Lc-Xwp2000 Multimedia Projector Owners Manual

							
How to Connect 
1. Connect to a video source 
The Projector can receive compos ite AV ,YPbPr and S-Video.  
Connect RCA plug at projector and video source ( like DVD  
player) for video signal. Please contact with your dealer for  
optional cable.  
2. Connect RCA plug ( white and red) to audio source ( like DVD  
player) and connect the phone  jack to projector for audio  
signal.  
30 
Connecting Video to the Projector 
						

							
How to Connect 
3.  Connect YPbPr plug at projector computer in 2 port and video  
source ( like DVD player) for video signal. 
4. For S-Video, using S-Video ca ble connect to projector and  
video source for video signal.  
31  
						

							
Basic Operation 
Turning on the Projector - Procedure
1.  Check the power is turned off for the projector and all components 
connected to the projector. 
2. Remove the lens cover. 
3. Connect the power cord to the projector. 
4. Turn on the power switch. 
5. Press the POWER button on the control panel or on the remote control. 
2 1 
5 
3 
KEYSTONE 
INPUT 4 BLANK 
32 
A  
						

							
Basic Operation 
Turnin g  on the Pro j ector - Procedure 
6.  The power indicator will flash green. 
7. Press t he I n put b u t t on on the con trol p a n el or on the remote 
8. Rotate t he zoom ring to adjust the screen size. 
9. Rotate t he focus ring to adjust t he focus. 
6 POWER LAMP 
9 
8 
6 
KEYSTONE 
INPUT 
BLANK 
33 
control to select the appropriate source.  
						

							
Basic Operation 
Turnin g  off the Pro j ector - Procedure 
1. Press the power button on the projector or remote control. The 
power off confirmation message appears . 
2. Press the power button again and the projector will enter cool-down 
mode. The lamp shuts off, the lamp indicator flashes red, and the 
fans continue to run for approximately two minutes. During the cool 
down sequence the projector will not respond to any control panel 
or remote control buttons. 
Do not set the power s w i tch to off or u nplu g  t he  
projector during the cool-down sequence. Not allowing  
the lamp to cool properly will greatly reduce the life  
of the lamp.  
C A U T I O N 
3. After the cool-down sequence is completed the fans will shut of f 
and the lamp indicator will stop flashing. The projector is now in 
standby mode and can be turned back on with the remote control 
or control panel. If the projector will not be used for an extended 
period, set the power switch to off and disconnect the power cord. 
34  
						

							
Basic Operation 
Adjusting the Screen Image
1. Adjusting the image size 
Rotate the Zoom Ring  to adjust the image. 
2. Adjusting the image height 
Extend or retract the front adjustable foot to adjust the height of  
the image. 
3. Cor recting Keystone Distortion  
◆  Press the Keystone button  on the control panel.  
◆  Keystone correction mess age will be appeared.  
◆  Press ”Left/Right” button to  correct Keystone distortion.  
POWERLAMP
KEYSTONE
INPUT
BLANK
35 
Press ”Left button” to     
correct keystone distortion. 
Press ”Right button” to     
correct keystone distortion.  
						

							
Functio nso fMenu(OSD)
Turnonandturnof ftheprojector.1.
2.Blank button : Blanks the projected image. If the projector is left 
                      in Blank mode for more than 1 5 min utes, the
                      projector wi l l automatical ly sh ut off  the lamp and
                      enter cool-down mode.
3.Auto button :Automaticallyadjuststhesettingstomatchthecurrent
4. Input but ton :SelectsVIDEO orPCinput source.
5.Menu but ton:Enterorexitthemainmenu(ShowandhidetheOSD)
6.:Up/Downarrowbuttons,usedtonavigatethroughtheOSDMenus.
:Right/Leftarrowbut tons,usedtoselectandadjustOSDMenu
fu nctions.
7.QuickKey:Itcanbeselectedthe“Keystone/Brightness/Contrast/
Thereisa“QuickKey“ontheremotecontrolandprojectorkeypadas
well.
36
Control panel (keypad) Operating
A
POWER
1.Power but ton
5.Men u but ton
3.Auto but ton
4.Input but ton
LAMP
INPUT
KEYSTONE
Brightness sensor
6.Men u-Up/Down
Menu-Left/Right
7.Quick Key
2.Blank but ton
Power button : 
input.
Volume ”by pressing  Men u down but ton and adjusted
by pressing left/right but ton on the   control panel or 
the remote control. (Only Keystone can be selected 
and adjusted when the input source is no signal.)  
						

							
1.PICTURE
B rightness00 0/100Adjusts  the  overall  image  brightness  
Contrast00 0/100Adjusts  the  diffe rence  between  
light  and  dark  areas  of   the i mage  
Sharpness000/002Adjusts  the  image  sharpness
D isplaymodeSelect
Video
Presentation
Natural
Greenboard
User
Keep  the  sof t  tender  color  
For  computer  presentation  use  
Nature  color  
When  using  on  green  board
Adjustments  of   each  RGB  color
UserRed
UserGreen
UserB lue
000/100
000/100  
000/100  
Functio nso fMenu(OSD)
Co mput erMo de-PICTURE Menu
37
PowerfulEn hancebrightness 
						

							
2. AUDIO 
Volume 000/040 Adjusts the vo l u me 
Mute Off/on Mutes the volume on/off 
Functions of Menu (OSD) 
Computer Mode-AUDIO Menu
38  
						

							
3.SETTING 
H position 000/100 Move the image position horizontally.
V position 000/100 Move the image position vertically.
Phase 000/100 Set the synchronization polarity.
Frequency 000/100 Set the horizont al scanning frequency.
Auto keystone off/on Automatically Corrects keystone  
distortion in image i.e. press once to do 
once.  
Keystone V -80/+80 Corrects vertical keystone distortion in 
image.  
Auto sync execute  Sets all of the above settings 
automatically.  
Auto search off/on Search signal source automatically. 
Functions of Menu (OSD) 
Computer Mode-SETTING Menu 
39