Eiki Lc-Xwp2000 Multimedia Projector Owners Manual

							
Installation 
Setting Up the Projector 
The projector supports the following four different projection methods 
Front projection 
Rear 
A special method o f installation is required in order to suspend the 
projector from the ceiling. Please ask your dealer for details. 
20  
						

							
Installation
Setting Up the Projector 
Rear ceiling projection 
Front ceiling projection 
A special method o f installation is required in order to suspend the 
projector from the ceiling. Please ask your dealer for details. 
21  
						

							
Installation
Scre ensizeandProjectionDistance
Thedistancebetweentheprojectorandscreendeterminesthe
actualimagesize.Refertothetablebelowtodeterminetheimage
sizeatagivendistance.
A:BRatio=6.5:1
A
B 
22
Thevaluesshownbelowareapproximateandmayvaryfromactualsizes.
Scre en Size (inches)
(WxH) mm
Scre en Size (inches)
(WxH) mm
Scre en Size (inches)
(WxH) mm
Zo om(min)
Zo om(min)
Zo om(min)
Zo om(max)
Zo om(max)
Zo om(max)
5 0”6 0”
8 0”1 0 0”
1 5 0”
1 0 1 6 x 7 621 2 1 9 x 9 14
3.8’ (1.2 m)
3.3’ (1.0 m)
4.6’ (1.4 m)
3.8’ (1.2 m)
1 6 2 6 x 1 2 192 0 3 2 x 1 5 24
6.2’ (1.9 m)7.8’ (2.4 m)
5.2’ (1.6 m)6.5’ (2.0 m)
3 0 4 8 x 2 2 86
1 1.9’ (3.7 m)
9.9’ (3.0 m) 
						

							
Installation
Adjusting the Image Position 
Use the adjustable foot at the front of the projector to set the image 
height. Rotate the adjustable foot at the rear of the projector to fine- 
tune the image position. 
When the foot is adjusted, it may cause the shape of the projected 
image to become distorted. Use the keystone correction function to 
correct this distortion. 
To retract the front adjustable foot, press the foot adjust button. The  
front adjustable foot will slowly retract inside the projector. 
23  
						

							
Installation
Moving the Projector
1. Use the carry bag when moving the projector.(option) 
2. Replace the lens cover and retract the front adjustable foot when 
moving the projector to prevent damage to the projector. 
carry bag 
( O p t i o n a l ,  p l e a s e  c o n t a c t  y o u r  d e a l e r  f o r  m o r e  i n f o r m a t i o n ) 
C A U T I O N 
The optional carry bag is intended to protect the projecto r 
from dust and scratches on the surface of the cabinet. It is 
not designed to protect the projector from external shock. 
Do not transport the projector in an unsuitable transpor t 
case when using a courier or transport service. This ma y 
cause damage to the projector. 
24  
						

							
Instal lation
 Turning on the Projector
POWER
Removethelenscover.
Con necttheprojector’spowercablewiththeprojector,andinsert
thepowercableintoawallsocket.
TurnontheACpowerswitchoftheprojector. Thepowerindicator
lightsgreenandslowflashing.Projectorworksinstandbymode.
Pressthepowerbuttontoturnon the projector.  ThepowerLED  
beginstogreenandlampLEDbeginstored,andtheprojectorwill  
belampedon.
25 
						

							
Installation
Turning on the Projector
WARNING If no image a re pro jected, change the input sign al. 
POWER LAMP 
A 
KEYSTONE 
INPUT 
BLANK 
When using a laptop or a PC with an in built monitor, select external  
video  output on the computer. 
26  
						

							
Installation
Connecting PC to the Projector
27
To connect Computer cable (RGB).
To Computer monitor portComputer 1 and Computer 2
Computer cable 
						

							
How to Connect 
Desktop PC
Before starting, make sure that the projector and computers are both 
turned off. 
1. Connect the computer cable. 
Connect either end of the computer cable to the projector’s Computer  
in 1 or Computer in 2  
Disconnect the monitor cable from the computer and connect the 
other end of the terminal where the monitor cable is disconnected 
from the computer. 
If needed, connect the monitor cable of the computer monitor to  
the projector’s Monitor Out. 
Tighten the screw on all connectors. 
2. Connect the audio cable if necessary. 
Connect one end of the audio cable to the Audio in jack on the 
projector. 
Connect the other end of the audio cable to the audio output port 
on the computer.
VGA 
Desktop PC 
28  
						

							
How to Connect 
Laptop PC 
Before beginning, make sure that the projector and computers are both  
turned off. 
1. Connect the computer cable. 
Connect either end of the computer cable to the projector’s  Computer 
in 1.  
Connect the other end of the project cable to the monitor out  
connection on the laptop. 
Tighten the all connectors. 
2. Connect the audio cable if necessary. 
Connect one end of the audio cable to the Audio in jack on the 
projector. 
Connect the other end of the audio cable to the audio output port 
on the laptop PC. 
Laptop PC 
29