Edimax Router Wireless VPN Broadband User Manual

 
Parameters  Description Current Password  Enter your current password for the remote 
management administrator to login to your 
Broadband router.  
  Note: By default there is NO password  New Password  Enter your new password   Confirmed Password   Enter your new password again for verification 
purposes 
   Note: If you forget your password, you’ll have to 
reset the router to the factory default (No password) 
with the reset button (see router’s back panel) 
Click < Apply>  at the bottom of the...

 
Host Address  This is the IP address of the host in the Internet that will have management/configuration access to the Broadband 
router from a remote site. Th is means if you are at home 
and your home IP address has been designated the 
Remote Management host IP address for this router 
(located in your company office), then you are able to 
configure this router from your  home. If the Host Address is 
left  0.0.0.0 this means anyone can access the router’s web-
based configuration from a remote...

 
 Parameters  Description 2.2.1 Wireless ISP                Your wireless ISP will give you the wireless Internet broadband access 
 2.2.2 Dynamic IP address  Your ISP will automatically give you an IP address 
 2.2.3 Static IP address  Your ISP has given you an IP address  already  
 2.2.4 PPPoE  Your ISP requires PPPoE connection.  2.2.5 PPTP  Your ISP requires you to use a Point-to-Point 
Tunneling Protocol (PPTP) connection.  
 2.2.6 L2TP  Your ISP requires L2TP connection.  2.2.7 Telstra Big Pond...

 
 2.2.1 Wireless ISP Choose the the “WAN Type”,  “Wireless ISP” and “Apply” button for 
connecting to the wireless Access  Point and proceed to the manual’s 
relevant sub-section. 
 Once you have made a selection, click < More Configuration> at the 
bottom of the screen and proceed to the manual’s relevant sub-section 
 2.2.2 Dynamic IP Choose the Dynamic IP selection if your ISP will automatically give you an 
IP address. Some ISP’s may also require that you fill in additional 
information such as...

 
matching IP address. Most ISPs provide a DNS server for speed and 
convenience. If your Service Provider connects you to the Internet with 
dynamic IP settings, it is likely that  the DNS server IP address is provided 
automatically. However, if there is a DN S server that you would rather use, 
you need to specify the IP address of that DNS server here. 
 
Parameters   Description  Domain Name Server (DNS) Server  This is the ISP’s DNS server IP  address that they gave you; or you 
can specify your...

 
2.2.9 DDNS DDNS allows you to map the static domain name to a dynamic IP address. 
You must get an account, password and your static domain name from the 
DDNS service providers. This router supports DynDNS, TZO and other 
common DDNS service providers. 
 
    Parameters Default  Description  Enable/Disable            Disable  Enable/Disable the DDNS function of this  router 
 Provider                         Select a DDNS service provider  Domain name                            Your static domain...

 
Click   at the bottom of the screen to save the above 
configurations. You can now configur e other advance sections or start 
using the router (with the advance settings in place) 
 2.3 LAN  The LAN Port screen below allows you to specify a private IP address for 
your router’s LAN ports as well as a subnet mask for your LAN segment. 
 
  Parameters Default  Description  LAN IP IP address                192.168.2.1  This is the router’s LAN port IP  address (Your LAN clients default 
gateway IP...

 
DHCP Server                Enabled           You can enable or disable the DHCP server. By enabling the 
DHCP server the router will 
automatically give your LAN clients 
an IP address. If the DHCP is not 
enabled then you’ll have to 
manually set your LAN client’s IP 
addresses; make sure the LAN 
Client is in the same subnet as this 
broadband router if you want the 
router to be your LAN client’s 
default gateway 
 Lease Time  The DHCP when enabled will 
temporarily give your LAN clients an 
IP...

 
Intranet. It supports WEP and WPA2 encryption to enhance the security of 
your wireless network. 
 
  Parameters Default  Description  Enable or disable         Enable    You can select to enable or disable the wireless access point module of this 
router. 
Wireless module function Click   at the bottom of the screen to save the above 
configurations. You can now configur e other advance sections or start 
using the router (with the advance settings in place) 
 2.4.1 Basic Settings  You can set...

 
  Parameters         Default    Description  Mode                   It allows you to set the AP to AP, Station, 
Bridge or WDS mode. 
 Band                    It allows you to set the AP fix at 802.11b or 
802.11g mode. You also can select B+G 
mode to allow the AP select 802.11b and 
802.11g connection automatically. 
 ESSID                default  This is the name of the wireless LAN. All the  devices in the same wireless LAN should 
have the same ESSID. 
 Channel Number      11  The channel used by...