Dukane Projector 6430 User Manual

							14
English ...
Introduction
Battery Installation
Remote Control Precautions
• Handle the remote control carefully.
• If the remote control gets wet, wipe it dry immediately.
• Avoid excessive heat and humidity.
• Do not place the battery upside down.
• Replace only with the same or equivalent type recommended by 
the manufacturer.
• Dispose of used batteries according to your local regulations.
1. Press firmly and slide the battery cover off.
2.   Install new batteries (AAA). 
Ensure that you have the 
batteries’ polarity (+/–) 
aligned correctly.
3.  Slip the cover back over the 
batteries until it snaps into 
place. Do not mix different 
types of batteries or new and 
old batteries.
	The infrared signal 
operates by line-of-
sight up to a distance 
of about 22 feet/7 m 
and within a 60-degree 
angle of the remote 
sensor on the projector 
cabinet.
	 The projector will 
not respond if there 
are objects between 
the remote control 
and the sensor, or if 
strong light falls on the 
sensor. Weak batteries 
will also prevent the 
remote control from 
properly operating the 
projector. 
						

							15... English
Introduction
Using the utility software “Virtual Remote Tool” that you can 
download from our web site (http://www.nec-display.com/ 
dl/en/index.html), Virtual Remote screen (or toolbar) can be 
displayed on your computer screen.
This will help you perform operations such as projector’s 
power on or off and signal selection via a LAN connection.
Toolbar
Virtual Remote screen
This section provides an outline of preparation for use of 
Virtual Remote Tool.
For information on how to use Virtual Remote Tool, see Help 
of Virtual Remote Tool. Please refer to page 19.
Step 1: Install Virtual Remote Tool on the computer. Please 
refer to page 16.
Step 2: Connect the projector to a LAN.  Please refer to page 
17.
Step 3: Start Virtual Remote Tool. Please refer to page 18.
TIP:
•   Virtual Remote Tool can be used with a serial connection.
•   For update information on Virtual Remote Tool, visit our website:
http://www.nec-display.com/dl/en/index.html
Operating the Projector Via the LAN 
(Virtual Remote Tool)
Using the Downloadable Software
	 The projector does 
not support the LAN 
automatic search fea-
ture of Virtual Remote 
Tool. To connect the 
projector, register an 
IP address manually. 
						

							16
English ...
Introduction
Step 1: Install Virtual Remote Tool on the computer
•   Supported OS
Virtual Remote Tool will run on the following operating systems.
Windows 8.1 *1, Windows 8.1 Pro *1, Windows 8.1 Enterprise *1, Windows 8 *1,  Windows 8 Pro *1, Windows 8 Enterprise *1, 
Windows 7 Home Basic, Windows 7 Home Premium, Windows 7 Professional, Windows 7 Enterprise, Windows 7 Ultimate
Windows Vista Home Basic, Windows Vista Home Premium, Windows Vista  Business,
Windows Vista Enterprise, Windows Vista Ultimate
Windows XP Home Edition *1, Windows XP Professional
*1:   To run Virtual Remote Tool, “Microsoft .NET Framework Version 2.0” is required. The Microsoft .NET Framework Version is available from Micro -
soft’s web page. Install the Microsoft .NET Framework Version 2.0, 3.0 or 
3.5 on your computer.
1   Download the updated VRT exe file from our web site
(http://www.nec-display.com/dl/en/index.html).
2  Double-click the VRT. exe icon.
The Installer will start and the Wizard screen will appear.
3 Click “Next”.
“END USER LICENSE AGREEMENT” screen will be displayed.
	To install or 
uninstall the program, 
the Windows user 
account must have 
[Administrator] 
privilege (Windows 
8.1, Windows 8, 
Windows 7, and 
Windows Vista).
	 Exit all running 
programs before 
installation. If another 
program is running, 
the installation may 
not be completed. 
						

							17... English
Introduction
Read “END USER LICENSE AGREEMENT” carefully.
4  If you agree, click “I accept the terms in the license agreement” \
and then 
click “Next”.
Follow the instructions on the installer screens to complete the 
installation.
After the installation is completed, the shortcut icon for Virtual 
Remote Tool.
TIP:Uninstalling Virtual Remote Tool
•   Preparation
        Exit Virtual Remote Tool before uninstalling. To uninstall Virtual Remote
        Tool, the Windows user account must have “Administrator” privilege 
    “(Windows 8.1, Windows 8, Windows 7 and Windows Vista)” or 
    “Computer Administrator” privilege (Windows XP).
•   For Windows 8.1/Windows 8/Windows 7/Windows Vista
1. Click “Start” and then “Control Panel”.
The Control Panel window will be displayed.
2. Click “Uninstall a program” under “Programs”.
The “Programs and Features” window will be displayed.
3. Select Virtual Remote Tool and click it.
4. Click “Uninstall/Change” or “Uninstall”.
    When the “User Account Control” window is displayed, click
    “Continue”. Follow the instructions on the screens to complete the 
     uninstallation.
•   For Windows XP
1. Click “Start” and then “Control Panel”.
The Control Panel window will be displayed.
2. Double-click “Add / Remove Programs”.
The Add / Remove Programs window will be displayed.
3. Click Virtual Remote Tool from the list and then click “Remove”.
Follow the instructions on the screens to complete the uninstallation.
Step 2: Connect the projector to a LAN Connect the projector to the LAN by following the instructions in 
“Connecting the Projector” on pages 25-26 and “How to use web 
browser to control your projector” in pages 64-68. 
						

							18
English ...
Introduction
Step 3: Start Virtual Remote Tool
Start using the shortcut icon
Start from the Start menu
Click [Start] -> [All Programs] or [Programs] -> [NEC Projector 
User Supportware] -> [Virtual Remote Tool] -> [Virtual Remote 
Tool].
When Virtual Remote Tool starts for the first time, “Easy Setup” 
window will be displayed.
The “Easy Setup” feature is not available on this model. Click 
“Close Easy Setup”. 
Closing the “Easy Setup” window will display the “Projector 
List” window. Click “Close”. This will display the Virtual Remote 
screen. To connect the projector, register an IP address manually.
TIP:
•   The Virtual Remote Tool screen (or Toolbar) can be displayed without 
displaying “Easy Setup” window.
    To do so, click to place a check mark for “Do not use Easy Setup next 
    time” on the screen.
	 When “NORMAL” 
is selected for 
“STANDBY MODE” 
from the menu, the 
projector cannot 
be controlled via 
the serial cable or 
network (wired LAN) 
connection.. 
						

							19... English
Introduction
Exiting Virtual Remote Tool
1  Click the Virtual Remote Tool icon  on the Taskbar.
The pop-up menu will be displayed.
2 Click “Exit”.
The Virtual Remote Tool will be closed.
Viewing the help file of Virtual Remote Tool
Displaying the help file using the taskbar
1  Click the Virtual Remote Tool icon on the taskbar when Virtual Remote 
Tool is running.
The pop-up menu will be displayed.
2 Click “Help”.
The Help screen will be displayed.
Displaying the help file using the Start Menu.
Click “Start” -> “All programs” or “Programs” -> “NEC Projector
User Supportware” -> “Virtual Remote Tool” and then “Virtual
Remote Tool Help” in this order.
The Help screen will be displayed. 
						

							20
English ...
Introduction
Controlling the Projector over a LAN 
[Using on Windows]
Using the utility software “PC Control Utility Pro 4” that you 
can download from our web site  
(http://www.nec-display.com/dl/en/index.html), the projector 
can be controlled from a computer over a LAN.
Control Functions
Power On/Off, signal selection, picture freeze, picture mute, 
audio mute, adjusting, error message notification, event 
schedule.
Screen of PC Control Utility Pro 4
This section provides an outline of preparation for use of PC Control 
Utility Pro 4. For information on how to use PC Control Utility Pro 4, 
see Help of PC Control Utility Pro 4.
•   Step 1: Install PC Control Utility Pro 4 on the computer. Please see 
the page 21.
•  Step 2: Connect the projector to a LAN. Please see the page 22.
•  Step 3: Start PC Control Utility Pro 4. Please see the page 22.
TIP:
•  PC Control Utility Pro 4 can be used with a serial connection.
•   For update information on PC Control Utility Pro 4, visit our website: 
http://www.nec-display.com/dl/en/index.html
	 When the projector 
is in the standby 
condition, the Error 
Alert function of PC 
Control Utility Pro 4/ 
PC Control Utility Pro 
5 are not available.
To make this function 
available even in the 
standby condition, 
use the E-Mail Alert 
function of the 
projector. 
(PC Control Utility Pro 4 for Windows/PC Control 
Utility Pro 5 for Mac OS) 
						

							21... English
Introduction
Step 1: Install PC Control Utility Pro 4 on the computer
 •  Supported OS - PC Control Utility Pro 4 will run on the following operating systems.
Windows 8.1*1, Windows 8.1 Pro *1, Windows 8.1 Enterprise *1, Windows 8 *1, Windows 8 Pro *1, Windows 8 Enterprise *1,
Windows 7 Home Basic, Windows 7 Home Premium, Windows 7 
Professional, Windows 7 Enterprise, Windows 7 Ultimate
Windows Vista Home Basic, Windows Vista Home Premium, 
Windows Vista Business, Windows Vista Enterprise, Windows Vista 
Ultimate 
Windows XP Home Edition *1, Windows XP Professional *1
*1:   To run PC Control Utility Pro 4, “Microsoft .NET Framework Version 2.0” is required. The Microsoft .NET Framework Version is available from Micro -
soft’s web page. Install the Microsoft .NET Framework Version 2.0, 3.0 or 3.5 
on your computer. 
1   Connect your computer to the Internet and download the updated PCCUP4 
exe file from our web site (http://www.nec-display.com/dl/en/index.html).
2  Double-click the PCCUP4. exe icon.
The Installer will start and the Wizard screen will appear.
3 Click “Next”.
“END USER LICENSE AGREEMENT” screen will be displayed.
	To install or 
uninstall the program, 
the Windows user 
account must have 
[Administrator] 
privilege (Windows 
8.1, Windows 8, 
Windows 7, and 
Windows Vista)
	 Exit all running 
programs before 
installation. If another 
program is running, 
the installation may 
not be completed. 
						

							22
English ...
Introduction
Read “END USER LICENSE AGREEMENT” carefully.
4   If you agree, click “I accept the terms in the license agreement” \
and then 
click “Next”.
Follow the instructions on the installer screens to complete the 
installation.
TIP:Uninstalling PC Control Utility Pro 4
•   To uninstall PC Control Utility Pro 4, do the same procedures stated as in 
“Uninstalling Virtual Remote Tool”. Read “Virtual Remote Tool” as “PC 
Control Utility Pro 4”
Step 2: Connect the projector to a LAN
Connect the projector to the LAN by following the instructions in 
“Connecting the Projector” on pages 25-26 and “How to use web 
browser to control your projector” in pages 64-65.
Step 3: Start PC Control Utility Pro 4 Click “Start” -> “All programs” or “Programs” -> “NEC Projector 
User Supportware” -> “PC Control Utility Pro 4” -> “PC Control 
Utility Pro 4”.
TIP: Viewing the Help of PC Control Utility Pro 4
•  Displaying the Help file of PC Control Utility Pro 4 while it is running.  
Click “Help (H)” -> “Help (H)” of window of PC Control Utility Pro 4 in 
this order. 
The pop-up menu will be displayed.
•   Displaying the help file using the Start Menu.   
Click “Start” -> “All programs” or “Programs” -> “NEC Projector User 
Supportware” -> “PC Control Utility Pro 4” -> “PC Control Utility Pro 4 
Help”. 
The Help screen will be displayed.
	 For the Schedule 
function of the PC 
Control utility Pro 4 to 
work, you must have 
your computer run-
ning and not in stand-
by/sleep mode. Select 
“Power Options” from 
the “Control Panel” in 
Windows and disable 
its standby/sleep 
mode before running 
the scheduler.
[Example] For Win-
dows 7:
Select “Control 
Panel” -> “System and 
Security” -> “Power 
Options” -> “Change 
when the computer 
sleeps” -> “Put the 
computer to sleep” -> 
”Never”. 
	 When “NORMAL” 
is selected for 
“STANDBY MODE” 
from the menu, the 
projector cannot 
be controlled via 
the serial cable or 
network (wired LAN) 
connection.
	 The projector 
does not support the 
LAN automatic search 
feature of PC Control 
Utility Pro 4. To con-
nect the projector, 
register an IP address 
manually.
PC Control Utility Pro 5 for Mac OS
Step 1: Install PC Control Utility Pro 5 on the computer
1   Connect your computer to the Internet and visit our website (http://www\
.
nec-display.com/dl/en/index.html).
2  Download the updated PC Control Utility Pro 5 from our website.
3  In Finder, control-click (“control” + click) or right click the \
PC Control 
Utility Pro 5.pkg.
4  Select “Open” from the top of contextual menu that appears. 
						

							23... English
Introduction
5  Click “Open” in the dialog box. If prompted, enter an administrato\
r name 
and password.
The installer will start.
6   Click “Next”.
“END USER LICENSE AGREEMENT” screen will be displayed.
7  Read “END USER LICENSE AGREEMENT” and click “Next”. 
The confirmation window will be displayed.
8  Click “I accept the terms in the license agreement”.
Follow the instructions on the installer screens to complete the install\
ation.
Step 2: Connect the projector to a LAN
Connect the projector to the LAN by following the instructions in 
“Connecting the Projector”.  Please see pages 25-26.
Step 3: Start PC Control Utility Pro 5
1. Open your Applications folder in Mac OS.
2. Click the “PC Control Utility Pro 5” folder.
3. Click the “PC Control Utility Pro 5” icon. 
PC Control Utility Pro 5 will start.
 
TIP: Viewing the Help of PC Control Utility Pro 5
•   Displaying the Help file of PC Control Utility Pro 5 while it is running.
•   From the menu bar, click “Help” → “Help” in this order. 
The Help screen will be displayed
•   Displaying the Help using the Dock
1. Open “Application Folder” in Mac OS.
2. Click the “PC Control Utility Pro 5” folder.
3. Click the “PC Control Utility Pro 5 Help” icon.
The Help screen will be displayed.
TIP: Uninstalling a software program
1. Put the “PC Control Utility Pro 5” folder to the Trash icon.
2. Put the configuration file of PC Control Utility Pro 5 to the Trash icon. 
• The configuration file of PC Control Utility Pro 5 is located in “/Users/ /Application Data/NEC Projector User Supportware/
PC Control Utility Pro 5”.  
	 For the Schedule 
function of the PC 
Control utility Pro 5 
to work, you must 
have your computer 
running and not in 
sleep mode. Select 
“Energy Saver” 
from the “System 
Preferences” in Mac 
and disable its sleep 
mode before running 
the scheduler.
	 When [NORMAL] 
is selected for 
[STANDBY MODE] 
from the menu, the 
projector cannot be 
turned on via the 
network.