Dukane Projector 6430 User Manual

							94
English ...
Appendices
(1) HDMI - 3D Timing
SignalResolution 
(dots) Aspect 
Ratio Refresh Rate
[Hz]
For PC Signal
XGA1024x768 *14:3 60/120 *5
1280x720
1280x72016:9 60/120 RB *5
WXGA
1280x800 *216:10 60/120 RB *5
Full HD
1920x1080 *316:9 60
For Video Signal SDTV (480i)
720x4804:3/16:9 60
For HDMI 3D
720p (Frame Packing) 1280x720
16:950/60/59.94
1080p (Frame Packing) 1920x108016:923.98/24
1080i (Side by Side (Half)) 1920x108016:950/60/59.94
1080P (Side by Side (Half)) 1920x108016:950/60/59.94 *6
720p (Top and Bottom) 1280x72016:950/60/59.94
1080p (Top and Bottom) 1920x108016:923.98/24
*1  XGA Model Real Resolution
*2  WXGA Model Real Resolution
*3  1080p Model Real Resolution
*4  The projector may fail to display these signals correctly
      when [AUTO] is selected for [ASPECT RATIO] in the 
      on-screen menu.
The factory default is [AUTO] for [ASPECT RATIO]. To display these 
signals, select [16:9] for [ASPECT RATIO].
*5  The 120 Hz signals are support frame sequential format only.
*6  Select manually. 
						

							95... English
Appendices
TIP:
•  An image with higher or lower resolution than the projector’s native 
resolution will be displayed with scaling technology.
•  Sync on Green and Composite sync signals are not supported.
•  Signals other than those specified in the table above may not be displayed 
correctly. If this should happen, change the refresh rate or resolution on 
your PC. Refer to Display Properties help section of your PC for proce-
dures.
(2) MHL Signal
SignalResolution (dots) Aspect 
Ratio Refresh Rate (Hz)
VGA
640x480 4:359.94/60
HDTV (1080p) 1920x108016:923.97/24/50/59.94/60
HDTV (1080i) 1920x108016:950/59.94/60
HDTV (720p) 1280x72016:950/59.94/60
SDTV (480p) 720x4804:3/16:9 59.94/60
SDTV (576p) 720x5764:3/16:9 50
SDTV (480i)720 x 480(1440x480i)4:3/16:9 59.94/60
SDTV (576i)
720 x 576(1440x576i)4:3/16:9 50 
						

							96
English ...
Appendices
130,00 (5,12”)219,00 (8,62”)
96,00 (3,78”)79,00 (3,11”)
59,00 (2,32”)
116,00 (4,57”)84,00 (3,31”)
142,00 (5,59”)142,00 (5,59”)
37,00 (1,46”)
150,00 (5,91”)
4-M4*L8 (Max)
for Ceiling Mount
57,89 (2,28”)
Please note that damage resulting from 
incorrect installation 
will invalidate the 
warranty.
Ceiling Mount Installation
  1.   To refuse the projector from damage, please use the 
ceiling mount kit for ceiling mount installation.
  2.   If you buy a ceiling mount from another company, 
please be sure to use the screw in correct size.  Screw 
size is vary depending on the thickness of the mount-
ing plate.
 Screw type: M4*4
 Maximum screw length: 8mm
 Minimum screw length: 6mm
Warning: 1.  Be sure to keep at least 10 cm gap 
between the ceiling 
and the bottom of the 
projector.
2.  Avoid installing the projector near a heat 
source.
Unit: mm (inch) 
						

							97... English
Appendices
Cabinet Dimensions
103,00 (4,06”) 59,00 (2,32”)
324,00 (12,76”)
250,00 (9,84”) 43,41 (1,71”)
57,89 (2,28”)
91,50 (3.60”)
88,00 (3,46”)
9,80 (0,39”)
Unit: mm (inch) 
						

							98
English ...
Appendices
Pin Assignments of D-Sub COMPUTER Input 
Connector
Mini D-Sub 15 Pin Connector
1 2 3 4 5
11 12 13 14 15
6 7 8 9 10
Signal Level
Video signal : 0.7Vp-p (Analog)
Sync signal : TTL level
Pin No.RGB Signal (Analog) YCbCr Signal
1 Red Cr
2 Green Y
3 Blue Cb
4 Ground
5 Ground
6 Red Ground Cr Ground
7 Green Gro Y Ground
8 Blue Ground Cb Ground
9 No Connection
10 Sync Signal Ground
11 No Connection
12 Bi-directional DATA (SDA)
13 Horizontal Sync or Composite 
Sync
14 Vertical Sync
15 Data Clock 
						

							99... English
Appendices
PC Control Codes and Cable Connection
PC Control Codes
Function Code Data
POWER ON 02H00H00H00H00H02H
POWER OFF 02H01H00H00H00H03H
INPUT SELECT COMPUTER 02H03H00H00H02H01H01H09H
INPUT SELECT HDMI 1 02H03H00H00H02H01HA1H A9H
INPUT SELECT HDMI 2 02H03H00H00H02H01HA2HAAH
INPUT SELECT VIDEO 02H03H00H00H02H01H06H0EH
PICTURE MUTE ON 02H10H00H00H00H12H
PICTURE MUTE OFF 02H11H00H 00H00H13H
SOUND MUTE ON 02H12H00H00H00H14H
SOUND MUTE OFF 02H13H00H00H00H15H
NOTE: Contact your local dealer for a full list of the PC Control Codes if needed.
Cable Connection
Communication Protocol Baud rate  ....................................................38400 bps
Data length  .................................................8 bits
Parity   ...........................................................No parity
Stop bit  ........................................................One bit
X on/off  ........................................................None
Communications procedure  ....................Full duplex
PC Control Connector (D-SUB 9P)
3 4 5
21
9876
NOTE 1: Pins 1, 4, 6 and 9 are no used.NOTE 2: Jumper “Request to Send” and “Clear to Send” together on both ends of the cable to simplify cable connection.
To TxD of PCTo RxD of PCTo GND of PC
To RTS of PCTo CTS of PC 
						

							Power
		
No	power	(POWER	indicator	does	not	light 	green).	 		
Power	cable's	plug	is	fully	inserted	into	the	wall	outlet.	 		
Lamp	cover	is	installed	correctly.	 		
Lamp	Hours	Used	(lamp	operation	hours)	was	cleared	after	lamp	replacement.	 		
No	power	even	though	you	press	and	hold	the	POWER	button	for	a	minimum	of	1	second.
		
Shut	down	during	operation.	 	 	
Power	cable's	plug	is	fully	inserted	into	the	wall	outlet.	 		
Lamp	cover	is	installed	correctly	.	 		
Power	Management	is	turned	off	(only	models	with	the	Power	Management	function).
Video and Audio
		
No	image	is	displayed	from	your	PC	or	video	equipment	to	the	projector.	 	 	
Still	no	image	even	though	you	connect	the	projector	to	the	PC	first,	then	start	the	PC.	 		
Enabling	your	notebook	PC's	signal	output	to	the	projector.	 	 			 A	combination	of	function	keys	will	enable/disable	the	external	display.	Usually,	the	combination	of	the"Fn"	key	along	with	one	of	the	12	function	keys	turns	the	external	display	on	or	off.	 		
No	image	(blue 	background).	 		
Still	no	image	even	though	you	press	the	AUTO	ADJUST	button.	 		
Still	no	image	even	though	you	carry	out	[RESET]	in	the	projector's	menu.	 		
Signal	cable's	plug	is	fully	inserted	into	the	input	connector	A	message	appears	on	the	screen.	 	 (	_____________________________________________	)	 		
The	source	connected	to	the	projector	is	active	and	available.	 		
Still	no	image	even	though	you	adjust	the	brightness	and/or	the	contrast.	 		
Input	source’s	 resolution	and	frequency	are	supported	by	the	projector.		
Image	is	too	dark.	 	 	
Remains	unchanged	even	though	you	adjust	the	brightness	and/or	the	contrast.		
Image	is	distorted.	 	 	
Image	appears 	to	be	trapezoidal	(unchanged	even	though	 		
you	carry	out	the	[KEYSTONE]	adjustment).
		Parts	of	the	image	are	lost.	 		Still	unchanged	even	though	you	press	the	AUTO	ADJUST	button.	 		Still	unchanged	even	though	you	carry	out	[RESET]	in	the	projector's	menu.		Image	is	shifted	in	the	vertical	or	horizontal	direction.	 		Horizontal	and	vertical	positions	are	correctly	adjusted	on	a	computer	signal.	 		Input	source's	resolution	and	frequency	are	supported	by	the	projector.	 		Some	pixels	are	lost.		Image	is	flickering.	 		Still	unchanged	even	though	you	press	the	AUTO	ADJUST	button.	 		Still	unchanged	even	though	you	carry	out	[RESET]	in	the	projector's	menu.	 		Image	shows	flickering	or	color	drift	on	a	computer	signal.		Image	appears	blurry	or	out	of	focus.	 		Still	unchanged	even	though	you	checked	the	signal's	reso-lution	on	PC	and	changed	it	to	projector's	native	resolution.	 		The	throw	distance	is	within	47"	to	516"	/	1189	mm	to	
1328	mm	to	11955	mm			 		Still	unchanged	even	though	you	adjusted	the	focus.		No	sound.	 		Audio	cable	is	correctly	connected	to	the	audio	input	of	the	projector.	 		Still	unchanged	even	though	you	adjusted	the	volume	level.Other
		
Remote	control	does	not	work.	 	 	
No	obstacles	between	the	sensor	of	the	projector	and	the	remote	control.	 		
Projector	is	placed	near	a	fluorescent	light	that	can	disturb	the	infrared	remote	controls.	 		
Batteries	are	new	and	are	not	reversed	in	installation
		
Buttons	on	the	projector	cabinet	do	not	work.	 	 	
[CONTROL	PANEL	LOCK]	is	not	turned	on	in	the	menu.	 		
Still	unchanged 	even	though	you	press	and	hold	the	EXIT	button	for	minimum	of	10	seconds.
Troubleshooting Check List
Before contacting your dealer or service personnel, check the following list to be sure repairs are needed also by  
referring to the “Troubleshooting” section in your user’s manual. This checklist below will help us solve your   
problem more efficiently.
* Print the following pages.
Frequency of occurrence		always				sometimes	(How	often?_______________________)					other	(__________________)
13105 mm (6433 &6430), 39" to 432" /1002 mm to 10985 mm (6433W &6430W), 52" to 471"/
(6430HD) 
						

							In the space below please describe your problem in detail.
Information on application and environment where your projector is usedProjector
Model	number:
Serial	No.:
Date	of	purchase:
Lamp	operating	time	(hours):
Eco	Mode:		Off			Eco
Information	on	input	signal:
Horizontal	synch	frequency	 [	 ]	kHz
Vertical	synch	frequency	 [	]	Hz
Synch	polarity	H			(+)			(-)
	V			(+)			(-)
Synch	type		Separate			Composite
		Sync	on	Green
STATUS	Indicator:
Steady	light		Orange			Green
Blinking	light	[	]	cycles
Remote	control	model	number:
Installation environment
Screen	size:		 inch
Screen	type:		White	matte			Beads			Polarization
			Wide	angle			High	contrast
Throw	distance:	 feet/inch/m
Orientation:		Ceiling	mount			Desktop
Power	outlet	connection:
		Connected	directly	 to	wall	outlet
		Connected	to	power	cord	extender	or	other	(the	number	of	connected	equipment______________)
		Connected	to	a	power	cord	reel	or	other	(the	number	of	connected	equipment______________)
Computer
Manufacturer:
Model	number:
Notebook	PC		/	Desktop		
Native	resolution:
Refresh	rate:
Video	adapter:
Other:
Video equipment
VCR,	DVD	player,	Video	camera,	Video	game	or	other
Manufacturer:
Model	number:
Signal cable
			
Model	number:		 Length:		 inch/m
Distribution	amplifier
Model	number:
Switcher
Model	number:
Adapter
Model	number:
Projector
PC
DVD Player
NStandard or other manufacturer's cable? 
						

							REGISTER YOUR PROJECTOR!
Please take time to register your new projector. This will insure an active warranty 
and your Peace of Mind program.
Visit our web site at www.dukaneav.com and submit your completed form online.
DUKANE CORP AV SERVICE DEPT 
2900 Dukane Drive
St Charles, IL 60174
800-676-2487 / 630-762-4032 
Fax  630-584-5156
[email protected]  
www.dukaneav.com 
						

							DUKANE CORP AV SERVICE DEPT 
2900 Dukane Drive
St Charles, IL 60174
800-676-2487 / 630-762-4032 
Fax  630-584-5156
[email protected]  
www.dukaneav.com
430-6430-6430W-6430HD-6433-6433W_User Manual-00